- FreeSWITCH-users - FreeSWITCH Mailing Lists

Dial number at registered extension
by Spencer Thomason 15 Mar '10

15 Mar '10

Hello all, Is there a way I can dial at number at a registered extension. Basically what I'd like to do is use Freeswitch as a SBC for a number of asterisk machines and I'd like to pass an incoming sip invite to a specific number at each one. Right now I'm specifying the IP in the bridge command like this sofia/default/NNNNNNNNNNN(a)xx.xx.xx.xx but if I dial the registered user directly it dials the contact address at the registered user and does not pass the inbound number. Basically what I'm trying to do is this: pstn -> ITSP -> freeswitch -> asterisk (1-n) Thanks, Spencer

5 10

FreeSWITCH to add SRTP to Asterisk
by schogge 15 Mar '10

15 Mar '10

Hi Community, I'm new to FreeSWITCH. What I have read so far it seems to be a very interesting project. For our company we are running an Asterisk PBX in a datacenter. After some years it is doing everything we want except of SRTP. Would it be possible to run FreeSWITCH in front of Asterisk to convert SRTP coming from our phones to RTP which is ok for Asterisk and vice versa? Thanks, schogge -- View this message in context: http://old.nabble.com/FreeSWITCH-to-add-SRTP-to-Asterisk-tp27901964p2790196… Sent from the Freeswitch-users mailing list archive at Nabble.com.

2 1

problem in sending calls to internal Gateway.
by Prabin Shrestha 15 Mar '10

15 Mar '10

hello, My extension are working properly. But they can't send calls to gateway. I have 2 interfaces, one with public and another with private lan. Gateway is in private lan. Please suggest. My configurations are as follows: /conf/sip_profiles/external.xml: <param name="rtp-ip" value="110.4.12.111"/> <param name="sip-ip" value="110.4.12.111"/> <param name="ext-rtp-ip" value="auto-nat"/> <param name="ext-sip-ip" value="auto-nat"/> /conf/sip_profiles/internal.xml: <param name="rtp-ip" value="192.168.1.11"/> <param name="sip-ip" value="192.168.1.11"/> <param name="hold-music" value="$${hold_music}"/> <param name="apply-nat-acl" value="nat.auto"/> haven't made any changes in conf/autoload_configs/acl.conf.xml to route calls from providers, /dialplan/public/providers.xml: <extension name="provider"> <condition field="network_addr" expression="200.144.44.177"/> <condition field="destination_number" expression="^(\d+)$"> <action application="transfer" data="$1 XML context_AX"/> </condition> </extension> gateway is defined at /conf/sip_profiles/internal/gateways.xml: <include> <gateway name="gateway_AX"> <param name="username" value="admin"/> <param name="password" value="nepal123"/> <param name="proxy" value="192.168.1.100"/> <param name="register" value="false"/> <param name="extension" value="1001"/> </gateway> </include> To route internal calls from extensions, /conf/dialplan/default.xml: <extension name="my_internal">  <condition field="destination_number" expression="^(d+)$"> <action application="bridge" data="sofia/gateway/gateway_AX/$1"/> </condition> </extension> to route calls from providers, conf/dialplan/inbound_routing.xml: <context name="context_AX"> <extension name="from_provider_to_AX">  <condition field="destination_number" expression="^9(\d+)$"> <action application="bridge" data="sofia/gateway/gateway_AX/$1"/> </condition> </extension> </context> Please help. The INTERNET now has a personality. YOURS! See your Yahoo! Homepage. http://in.yahoo.com/

2 1

not answering calls on TDM400 port
by Brian May 15 Mar '10

15 Mar '10

Hello, I noticed Freeswitch wasn't answering calls on one of the TDM400 ports yesterday. All other ports seemed to be OK. Nothing showed up on the console, set at debug log level. I restarted Freeswitch and it came good. What should I do if it happens again? Is there any debugging information I can extract from the system? If so how? Thanks -- Brian May <brian(a)microcomaustralia.com.au>

2 1

Re: [Freeswitch-users] Set/Export channel variable
by Brian West 15 Mar '10

15 Mar '10

We already set you a variable called sip_gateway_name when a call is placed out a gateway. You're also doing this wrong you should NEVER EVER do @$ipgwX as that data is in the gateway. You should simply do sofia/gateway/gwname/number /b On Mar 10, 2010, at 8:01 AM, Ahmed Ajmal wrote: > Hi > > I am trying to set a channel variable on the bridge application using this: > > <action application="bridge" data="[gw=gateway1]sofia/gateway/gw/$number@$ipgw1 | [gw=gateway2]sofia/gateway/gw/$number@$ipgw2"/> > > The application runs fine, what I now need to do is set/export the ‘gw’ channel variable for CDR so that I know which gateway was dialed. I have tried using set and export application but that doesn’t work. Please help. > > Thanks > Ahmed

2 1

errors and failures at snagoma+freeswitch
by Tzury Bar Yochay 15 Mar '10

15 Mar '10

Hi, Owe to an hardware failure I have had to reinstall my server. Originally I have had the combination of FreeSWITCH/Sangoma/LibPRI/OpenZap Getting recommendation to try the new sangoma prid I tried to follow the instructions found at http://wiki.sangoma.com/wanpipe-freeswitch-install Being unable to make it work, I search through the mailing-list and saw the specific versions which should be used. Followed these instruction as well, yet, it is not working. probing hardware shows all goos indications. When I try to originate from within the FreeSWITCH's CLI I get freeswitch@snaptrunk-02> originate openzap/smg_prid/a/0525133399 XML public 2010-03-14 16:09:14.575286 [CRIT] ozmod_sangoma_boost.c:254 SPAN is not online. -ERR NORMAL_CIRCUIT_CONGESTION 2010-03-14 16:09:14.575286 [ERR] switch_ivr_originate.c:2422 Cannot create outgoing channel of type [openzap] cause: [NORMAL_CIRCUIT_CONGESTION] freeswitch@snaptrunk-02> when I try to run #smg_ctrl start I get: smg_ctrl: sangoma_prid failed to start > smg_ctrl: check /var/log/sangoma_mgd.log for errors > *However, that file ( /var/log/sangoma_mgd.log) is empty. *I pastebin all relevant files at http://gist.github.com/332589* *I am using the latest freeswitch (svn trunk) I tried the smg with these versions (from ftp://ftp.sangoma.com/linux/custom/DavidYS/) - wanpipe-3.5.10.smg_pri.1.tgz - wanpipe-3.5.10.3.smg_pri-v1.58.tgz * *

3 2

doublenat outgoing call issue
by Bruce Hopkins 15 Mar '10

15 Mar '10

Hi, I wonder if some kind soul might be able please to help me by pointing out what I am doing wrong with my doublenat configuration. I have incoming calls from WAN --> LAN working fine, but when I try to call from LAN -->WAN, the Freeswitch CLI says: "[ERR} switch_ivr_originate.c.2389 CAnnot create outgoing channel of type [error] cause: [USER_NOT_REGISTERED]" The setup is essentially: phone_1 (192.168.a.b) --> NAT (public ip 1.2.3.4) --> Internet --> NAT (public ip 5.6.7.8) --> Freeswitch (192.168.x.y) --> phone_2 (192.168.x.z) Phone_1 is able to register with Freeswitch using a "doublenat" sip profile I set up using port 5090, created from the default external profile with the port changed. phone_1 can initiate calls to phone_2 fine with no problems with audio - everything works just fine in that direction. However when I try to call from phone_2 --> phone_1 I get the message "The person at extension 1002 is not available. Record your message at the tone." Meanwhile the CLI shows that Freeswitch says phone_1 is not registered. In trying to solve this I have run a Wireshark trace onthe PC running the phone_1 softphone to check that the SIP registration seems to go as I understand it should. the dialog is as follows: phone_1 --> FS request: REGISTER FS --> phone_1 status: 401 Unauthorised phone_1 --> FS request: REGISTER FS --> phone_1 status: 200 OK phone_1 --> FS request: SUBSCRIBE FS --> phone_1 status: 405 Method Not Allowed There does appear to be a difference here to what happens when phone_2 (on the same LAN as Freeswitch) registers. With phone_2 I see: phone_2 --> FS request: REGISTER FS --> phone_2 status: 401 Unauthorised phone_2 --> FS request: REGISTER FS --> phone_2 status 200 OK phone_2 --> FS request: SUBSCRIBE FS --> phone_2 status: 202 Accepted FS --> phone_2 request: NOTIFY phone_2 --> FS status: 200 OK More configuration details: In conf/sip_profiles/doublenat.xml I have not uncommented <param name="force-register-domain" value="$$(domain)"/> In conf/sip_profiles/doublenat.xml I have tried setting the context to each of public and default. This does not seem to make a difference. In conf/directory/doublenat.xml I have set the domain name to be the domain name registerd for Fs's external IP with DNS, and used by phone_1. In conf/directory/doublenat.xml I have tried both of the following 9I don't know if this is relevant) 1. Firstly with phone_1 registering to an extension in the default configuration, held in conf/directory/default/: <groups> <group name="default"> <users> <X-PRE-PROCESS cmd="include" data="default/*.xml"/> </users> </group> 2. Then I tried moving the .xml file for phone_1's extension to conf/drectory/doublenat/ and changed conf/directory/doublenat.xml to show: <groups> <group name="doublenat"> <users> <X-PRE-PROCESS cmd="include" data="doublenat/*.xml"/> </users> </group> Unfortunately this does not make a difference to the issue though. If anybody had the time to tell me what I am doing wrong I would be hugely grateful ! Many thanks in advance Bruce

4 18

regarding the recent sangoma boost
by Tzury Bar Yochay 15 Mar '10

15 Mar '10

one must run # mkdir /root/sangoma before head. otherwise, sangoma_prid will fail to start I discoverd this since /var/log/sangoma_mgd.log file was empty even though the line local2.* /var/log/sangoma_mgd.log exists in /etc/syslog.conf I did the following: # export LD_LIBRARY_PATH=/usr/lib/sangoma_prid # /usr/sbin/sangoma_prid &> sangoma_prid.log an then with # tail -f sangoma_prid.log I got ==> sangoma_prid.log <== ================System restart============= = Sangoma PRI Protocol Stack Daemon = = Version: 1.58 = = Date: Feb 18 2010 = = Wanpipe Release: wanpipe-3.5.10.3 = = Revision:Revision: 15364 = =========================================== sh: gen_fs_gcore.sh: not found touch: cannot touch `/root/sangoma/sangoma_prid.gcore.24821': No such file or directory /usr/bin/gcore: 83: cannot create /root/sangoma/sangoma_prid.gcore.24821: Directory nonexistent gcore: failed to create /root/sangoma/sangoma_prid.gcore.24794 I then ran `# mkdir /root/sangoma` and restart everything Right now I am facing another problem which hope to over come right after lunch the problem is this error freeswitch@snaptrunk-02> originate openzap/1/a/0525133399 XML public 2010-03-15 12:20:56.307066 [WARNING] ozmod_sangoma_boost.c:341 TX EVENT: CALL_START:(80) [w1g1] CSid=1 Seq=0 Cn=[N/A] Cd=[0525133399] Ci=[N/A] Rdnis=[] 2010-03-15 12:21:06.858887 [WARNING] sangoma_boost_client.c:221 TX EVENT (N): CALL_START_NACK:(82) [w1g1] Rc=0 CSid=1 Seq=1 2010-03-15 12:21:06.858887 [ERR] switch_ivr_originate.c:2422 Cannot create outgoing channel of type [openzap] cause: [RECOVERY_ON_TIMER_EXPIRE] -ERR RECOVERY_ON_TIMER_EXPIRE 2010-03-15 12:21:06.858887 [DEBUG] switch_ivr_originate.c:3220 Originate Resulted in Error Cause: 102 [RECOVERY_ON_TIMER_EXPIRE] freeswitch@snaptrunk-02>

1 0

Skypiax has been renamed as Skypopen
by Giovanni Maruzzelli 15 Mar '10

15 Mar '10

Ciao FreeSWITCHers, is with pleasure that we're announcing the renaming of mod_skypiax module to mod_skypopen. The new wiki page is at http://wiki.freeswitch.org/wiki/Mod_skypopen_Skype_Endpoint_and_Trunk To upgrade from a previous Skypiax installation, please read: http://wiki.freeswitch.org/wiki/Mod_skypopen_Skype_Endpoint_and_Trunk#Upgra… Many many many thanks to the wonderful FreeSWITCH team that make it all happens! -giovanni -- Sincerely, Giovanni Maruzzelli Cell : +39-347-2665618

2 2

LUA and LUASQL Install
by Aloysius Lloyd 15 Mar '10

15 Mar '10

Hi All, Can some one help me to install Lua . OS: CentOS 5.4 wget http://www.lua.org/ftp/lua-5.1.4.tar.gz tar zxf lua-5.1.4.tar.gz cd lua-5.1.4 make linux But getting error when running *make linux * * * *Here is the Output* In file included from lua.h:16, from lua.c:15: luaconf.h:275:31: error: readline/readline.h: No such file or directory luaconf.h:276:30: error: readline/history.h: No such file or directory lua.c: In function âpushlineâ: lua.c:182: warning: implicit declaration of function âreadlineâ lua.c:182: warning: assignment makes pointer from integer without a cast lua.c: In function âloadlineâ: lua.c:210: warning: implicit declaration of function âadd_historyâ make[2]: *** [lua.o] Error 1 make[2]: Leaving directory `/usr/src/lua-5.1.4/src' make[1]: *** [linux] Error 2 make[1]: Leaving directory `/usr/src/lua-5.1.4/src' make: *** [linux] Error 2 Thank you in advance. Thanks, Lloyd

3 6