Hi! The two TDM channels I have been using on my TDM400P card seem to have stopped working. No dialtone, no reaction to trying to make a call. ftdm list givews: +OK span: 1 (DECTTDM) type: analog physical_status: ok signaling_status: UP chan_count: 1 dialplan: XML context: dect dial_regex: fail_dial_regex: hold_music: analog_options none +OK span: 2 (DOORTDM) type: analog physical_status: ok signaling_status: UP chan_count: 1 dialplan: XML context: doorbell dial_regex: fail_dial_regex: hold_music: analog_options none +OK But immediately afterwards, I get: 2011-05-30 11:59:13.998318 [ERR] ftdm_io.c:4439 0:0: Failed to get alarms 2011-05-30 11:59:13.998318 [ERR] ftdm_io.c:5097 Failed to set channel alarms in span DOORTDM Julf
just to make sure. did u supply power to the interface card? it requires one just like hard disk/optical drives. On Mon, May 30, 2011 at 6:05 PM, Johan Helsingius <julf@julf.com> wrote:
Hi!
The two TDM channels I have been using on my TDM400P card seem to have stopped working. No dialtone, no reaction to trying to make a call.
ftdm list givews:
+OK span: 1 (DECTTDM) type: analog physical_status: ok signaling_status: UP chan_count: 1 dialplan: XML context: dect dial_regex: fail_dial_regex: hold_music: analog_options none +OK span: 2 (DOORTDM) type: analog physical_status: ok signaling_status: UP chan_count: 1 dialplan: XML context: doorbell dial_regex: fail_dial_regex: hold_music: analog_options none +OK
But immediately afterwards, I get:
2011-05-30 11:59:13.998318 [ERR] ftdm_io.c:4439 0:0: Failed to get alarms 2011-05-30 11:59:13.998318 [ERR] ftdm_io.c:5097 Failed to set channel alarms in span DOORTDM
Julf
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
just to make sure. did u supply power to the interface card? it requires one just like hard disk/optical drives.
I did, and nothing has changed in the hardware setup. Or not knowingly. Seems one of the modules might have blown, here is an extract from dmesg: [ 10.131010] Module 0: Installed -- AUTO FXS/DPO [ 10.644001] Unable to do INITIAL ProSLIC powerup on module 1 [ 11.156017] Unable to do INITIAL ProSLIC powerup on module 1 [ 11.156019] Module 1: FAILED FXS (FCC) [ 11.356308] Module 2: Installed -- AUTO FXO (FCC mode) [ 11.556308] Module 3: Installed -- AUTO FXO (FCC mode) [ 11.604259] Found a Wildcard TDM: Wildcard TDM400P REV E/F (3 modules) So one of the 4 modules refused to power up. Julf
you have 2 FXS modules. try to swap modules 0 and 1 to isolate whether the problem is in the daughter board or on the motherboard. this is far i can suggest. :-) On Mon, May 30, 2011 at 7:59 PM, Johan Helsingius <julf@julf.com> wrote:
just to make sure. did u supply power to the interface card? it requires one just like hard disk/optical drives.
I did, and nothing has changed in the hardware setup. Or not knowingly. Seems one of the modules might have blown, here is an extract from dmesg:
[ 10.131010] Module 0: Installed -- AUTO FXS/DPO [ 10.644001] Unable to do INITIAL ProSLIC powerup on module 1 [ 11.156017] Unable to do INITIAL ProSLIC powerup on module 1 [ 11.156019] Module 1: FAILED FXS (FCC) [ 11.356308] Module 2: Installed -- AUTO FXO (FCC mode) [ 11.556308] Module 3: Installed -- AUTO FXO (FCC mode)
[ 11.604259] Found a Wildcard TDM: Wildcard TDM400P REV E/F (3 modules)
So one of the 4 modules refused to power up.
Julf
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Nandy,
you have 2 FXS modules. try to swap modules 0 and 1 to isolate whether the problem is in the daughter board or on the motherboard. this is far i can suggest. :-)
Will try that next time I can shut down the system (it is in production use). I verified that one of the FXS modules is working, but it could still be a motherboard fault. Julf
participants (2)
-
Johan Helsingius
-
Nandy Dagondon