Solved this in a very hacky way - replying here in case this helps someone (although very hacky). open freeswitch/libs/freetdm/configure.ac find HAVE_SNG_ISDN="no" and change it to HAVE_SNG_ISDN="yes" finally, build FS again Please take care that this tells configure to build ftmod_sangoma_isdn even if its check for the library fails! Is there a less hacky / more straitforward way? Regards, Kshitij Saxena On Tue, Mar 25, 2014 at 7:46 PM, Kshitij Saxena <ksaxmail@gmail.com> wrote:

ok. The problem seems to be that ftmod_sangoma_isdn hasn't been compiled.

This is strange because I had compiled both wanpipe as well as libsng_isdn before configuring FS.

I repeated the steps again in case I had missed something - recompiled libsng_isdn, began FS with make clean, then bootstrap, then configure and make but ftmod_sangoma_isdn is still not being compiled!

Am I missing something? Is this a bug?

Regards, Kshitij

On Tue, Mar 25, 2014 at 6:03 PM, Kshitij Saxena <ksaxmail@gmail.com>wrote:

...

The setup is a Sangoma A101E card being run through Wanpipe 7.0.10 on an Ubuntu 13.10 machine.

wanrouter status shows "connected" but "originate freetdm/1/a/xxxxxxxxxx &bridge..." fails with the following error:

[ERR] ftdm_io.c:2674 [s1c1][1:1] outgoing_call method not implemented in this span!

Note that originate is successful with for other cahnnels (i.e. "originate user/1001 &bridge(9198)" works for example)

Would appreciate any guidance. Thanks!

Regards, Kshitij Saxena

Hi, Did you follow the install instructions for wanrouter driver and libsng_isdn library? These have to be performed before the Freeswitch bootstrap step. Freeswitch detects installed libraries during the ./bootstrap step. http://wiki.sangoma.com/wanpipe-freeswitch-ftdm-installation Regards, Robert From: Kshitij Saxena [mailto:ksaxmail@gmail.com] Sent: Tuesday, March 25, 2014 11:04 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] Originate fails for freetdm channel Solved this in a very hacky way - replying here in case this helps someone (although very hacky). open freeswitch/libs/freetdm/configure.ac<http://configure.ac> find HAVE_SNG_ISDN="no" and change it to HAVE_SNG_ISDN="yes" finally, build FS again Please take care that this tells configure to build ftmod_sangoma_isdn even if its check for the library fails! Is there a less hacky / more straitforward way? Regards, Kshitij Saxena On Tue, Mar 25, 2014 at 7:46 PM, Kshitij Saxena <ksaxmail@gmail.com<mailto:ksaxmail@gmail.com>> wrote: ok. The problem seems to be that ftmod_sangoma_isdn hasn't been compiled. This is strange because I had compiled both wanpipe as well as libsng_isdn before configuring FS. I repeated the steps again in case I had missed something - recompiled libsng_isdn, began FS with make clean, then bootstrap, then configure and make but ftmod_sangoma_isdn is still not being compiled! Am I missing something? Is this a bug? Regards, Kshitij On Tue, Mar 25, 2014 at 6:03 PM, Kshitij Saxena <ksaxmail@gmail.com<mailto:ksaxmail@gmail.com>> wrote: The setup is a Sangoma A101E card being run through Wanpipe 7.0.10 on an Ubuntu 13.10 machine. wanrouter status shows "connected" but "originate freetdm/1/a/xxxxxxxxxx &bridge..." fails with the following error: [ERR] ftdm_io.c:2674 [s1c1][1:1] outgoing_call method not implemented in this span! Note that originate is successful with for other cahnnels (i.e. "originate user/1001 &bridge(9198)" works for example) Would appreciate any guidance. Thanks! Regards, Kshitij Saxena