Sangoma A200 FXO Outgoing Problem
Hi, I have configured A200 and able to receive incoming calls. I am unable to dial out. Here are the logs. 2011-12-08 16:39:15.990089 [DEBUG] ftmod_analog.c:62 [s3c1][2:1] Changed state from DOWN to DIALING 2011-12-08 16:39:15.990089 [DEBUG] ftmod_analog.c:439 [s3c1][2:1] ANALOG CHANNEL thread starting. 2011-12-08 16:39:15.990089 [DEBUG] ftmod_analog.c:459 [s3c1][2:1] Initialized DTMF detection 2011-12-08 16:39:15.990089 [DEBUG] ftmod_analog.c:640 [s3c1][2:1] Completed state change from DOWN to DIALING in 0ms 2011-12-08 16:39:15.990089 [DEBUG] ftmod_analog.c:646 [s3c1][2:1] Executing state handler on 3:1 for DIALING 2011-12-08 16:39:21.009503 [DEBUG] ftmod_analog.c:505 [s3c1][2:1] Changed state from DIALING to BUSY 2011-12-08 16:39:21.030044 [DEBUG] ftmod_analog.c:640 [s3c1][2:1] Completed state change from DIALING to BUSY in 20ms 2011-12-08 16:39:21.030044 [DEBUG] ftmod_analog.c:646 [s3c1][2:1] Executing state handler on 3:1 for BUSY 2011-12-08 16:39:21.030044 [DEBUG] ftmod_analog.c:802 [s3c1][2:1] Changed state from BUSY to DOWN 2011-12-08 16:39:21.049928 [DEBUG] ftmod_analog.c:640 [s3c1][2:1] Completed state change from BUSY to DOWN in 20ms 2011-12-08 16:39:21.049928 [DEBUG] ftmod_analog.c:646 [s3c1][2:1] Executing state handler on 3:1 for DOWN 2011-12-08 16:39:21.049928 [DEBUG] ftmod_analog.c:944 [s3c1][2:1] Going onhook2011-12-08 16:39:21.049928 [DEBUG] switch_core_state_machine.c:362 (FreeTDM/3:1/9449905000) Running State Change CS_HANGUP Here is our dial plan <extension name="outgoing_bsnl"> <condition field="destination_number" expression="^9(\d{10})$"> <action application="bridge" data="freetdm/3/a/$1"/> </condition> </extension> I suspect FS is not detecting the dial tone on analogue channel. BTW, outgoing on our digital span works fine. Any suggestions? Thanks, Ryan
One thing to check is tones.conf. Do you have that configured correctly? -- View this message in context: http://freeswitch-users.2379917.n2.nabble.com/Sangoma-A200-FXO-Outgoing-Prob... Sent from the freeswitch-users mailing list archive at Nabble.com.
its freetdm/spanname/channelnumber/numbertodial You can't do a on those as far as I knew. /b On Dec 8, 2011, at 5:44 AM, Ryan V wrote:
Here is our dial plan
<extension name="outgoing_bsnl"> <condition field="destination_number" expression="^9(\d{10})$"> <action application="bridge" data="freetdm/3/a/$1"/> </condition> </extension>
On Fri, Dec 9, 2011 at 2:13 AM, Brian West <brian@freeswitch.org> wrote:
its freetdm/spanname/channelnumber/numbertodial
You can't do a on those as far as I knew.
I could see it trying to dial out on span 3 channel 1 even though I had "a" in <action application="bridge" data="freetdm/3/a/$1"/> Here is the excerpt from logs. [DEBUG] switch_core_state_machine.c:362 (FreeTDM/3:1/9449905000) Running State Change CS_HANGUP Thanks, Ryan
On Thu, Dec 8, 2011 at 6:49 PM, Ryan V <ryan@kaevee.com> wrote:
On Fri, Dec 9, 2011 at 2:13 AM, Brian West <brian@freeswitch.org> wrote:
its freetdm/spanname/channelnumber/numbertodial
You can't do a on those as far as I knew.
I could see it trying to dial out on span 3 channel 1 even though I had "a" in
<action application="bridge" data="freetdm/3/a/$1"/>
Here is the excerpt from logs.
[DEBUG] switch_core_state_machine.c:362 (FreeTDM/3:1/9449905000) Running State Change CS_HANGUP
Thanks,
Hi Ryan, Try disabling dial tone detection just to see if it works. <param name="wait-dialtone-timeout" value="0"/> You can also record the dial tone using "ftdm trace" command and then use wavesurfer (or perhaps audacity) to see the pair of frequencies used for dial tone and try to match them in your tones.conf if they are not already. *Moises Silva **Software Engineer, Development Manager*** msilva@sangoma.com Sangoma Technologies 100 Renfrew Drive, Suite 100, Markham, ON L3R 9R6 Canada t. +1 800 388 2475 (N. America) t. +1 905 474 1990 x128 f. +1 905 474 9223 **<http://www.sangoma.com/contact?utm_source=signature&utm_medium=email&utm_campaign=email+signatures> Products<http://sangoma.com/products?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Solutions<http://sangoma.com/solutions?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Events<http://sangoma.com/about_us/events?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Contact<http://www.sangoma.com/contact?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Wiki<http://wiki.sangoma.com/?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Facebook<http://www.facebook.com/pages/Sangoma-VoIP-Cards/43578453335?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Twitter<http://www.twitter.com/sangoma?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures>`| | YouTube<http://www.youtube.com/sangomatechnologies?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> VegaStream is now part of Sangoma!<http://sangoma.com/about_us/newsroom/news_releases/news/1488795/Sangoma_Acquires_All_Key_Assets_of_VegaStream.html> Ask us about both Gateway Appliances<http://sangoma.com/products/media_gateways/vega.html> and Internal Gateways<http://sangoma.com/products/software_products/netborder_suite/netborder_express.html>
Hi! I've had similar problem after separate contexts from default to external and internal. What is your tonegroup in autoload_configs/freetdm.conf.xml ? Make sure value of this parameter exist in tones.conf. Greet, Wojtek
participants (5)
-
Brian West
-
Jeff Lenk
-
Moises Silva
-
Ryan V
-
Wojtek Kochanowski