Openzap doesn't work

12 Jan 2009

>From my experience it shows red when:
- the cables are not connected
- the pri lines are not synchronized yet
- sometimes the telco provider has to reset the line

Best regards
Peter

Michael S Collins schrieb:
> This looks like a zaptel issue. Do we have any zaptel users familiar  
> with this issue? If not you should probably check on the asterisk list  
> for help. Once zaptel is working we can then see about getting openzap  
> up.
>
> -MC
>
> Sent from my iPhone
>
> On Jan 12, 2009, at 6:36 AM, "Franziska Röhler" <curly2009@gmx.de>  
> wrote:
>
>   
>> I use q931 too.
>>
>> openzap.conf.xml
>>
>> <configuration name="openzap.conf" description="OpenZAP  
>> Configuration">
>>  <settings>
>>    <param name="debug" value="0"/>
>>    <!--<param name="hold-music" value="$${moh_uri}"/>-->
>>    <!--<param name="enable-analog-option" value="call-swap"/>-->
>>    <!--<param name="enable-analog-option" value="3-way"/>-->
>>  </settings>
>>  <!-- one entry here per openzap span -->
>>  <pri_spans>
>>    <span id="1">
>>      <param name="mode" value="user"/>
>>      <param name="dialect" value="q931"/>
>>      <param name="dialplan" value="XML"/>
>>      <param name="context" value="default"/>
>>    </span>
>>  </pri_spans>
>> </configuration>
>>
>> openzap.conf
>>
>> [span zt]
>> name => OpenZap
>> number => 1
>> trunk_type => e1
>> b-channel => 1-15, 17-31
>> d-channel => 16
>>
>> cat /proc/zaptel/*
>> Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/ 
>> CCS/CRC4 RECOVERING
>>
>>           1 WCT1/0/1 Clear (In use) RED
>>           2 WCT1/0/2 Clear (In use) RED
>>           3 WCT1/0/3 Clear (In use) RED
>>           4 WCT1/0/4 Clear (In use) RED
>>           5 WCT1/0/5 Clear (In use) RED
>>           6 WCT1/0/6 Clear (In use) RED
>>           7 WCT1/0/7 Clear (In use) RED
>>           8 WCT1/0/8 Clear (In use) RED
>>           9 WCT1/0/9 Clear (In use) RED
>>          10 WCT1/0/10 Clear (In use) RED
>>          11 WCT1/0/11 Clear (In use) RED
>>          12 WCT1/0/12 Clear (In use) RED
>>          13 WCT1/0/13 Clear (In use) RED
>>          14 WCT1/0/14 Clear (In use) RED
>>          15 WCT1/0/15 Clear (In use) RED
>>          16 WCT1/0/16 HDLCFCS (In use) RED
>>          17 WCT1/0/17 Clear (In use) RED
>>          18 WCT1/0/18 Clear (In use) RED
>>          19 WCT1/0/19 Clear (In use) RED
>>          20 WCT1/0/20 Clear (In use) RED
>>          21 WCT1/0/21 Clear (In use) RED
>>          22 WCT1/0/22 Clear (In use) RED
>>          23 WCT1/0/23 Clear (In use) RED
>>          24 WCT1/0/24 Clear (In use) RED
>>          25 WCT1/0/25 Clear (In use) RED
>>          26 WCT1/0/26 Clear (In use) RED
>>          27 WCT1/0/27 Clear (In use) RD
>>          28 WCT1/0/28 Clear (In use) RED
>>          29 WCT1/0/29 Clear (In use) RED
>>          30 WCT1/0/30 Clear (In use) RED
>>          31 WCT1/0/31 Clear (In use) RED
>>
>> Why is it RED? zttool shows no alarms (ok) and ztfcg -vv shows that  
>> 31 Channels to configure.
>>
>>
>>
>>     
>>> I had the same problem a while ago with German PRI lines (S2M).
>>>
>>> Do you have
>>> <param name="dialect" value="q931"/>
>>> in your
>>> openzap.conf.xml?
>>>
>>> In older Versions of openzap I used euro, in newer releases this  
>>> didn't
>>> work any more, so I used q931.
>>>
>>> If this is not successfull,
>>>
>>> can you post your openzap.conf.xml and openzap.xml
>>> and the output of cat /proc/zaptel/*
>>>
>>> Best regards
>>> Peter
>>>
>>> curly2009@gmx.de schrieb:
>>>       
>>>> Hello,
>>>>
>>>> I'm a newbie in FS.
>>>>
>>>> I installed and configure Openzap and Zaptel. I have a PRI Digium
>>>>         
>>> Wildcard TE110P.
>>>       
>>>> When I call a number then I get an Error!
>>>>
>>>> 2009-01-12 10:20:01 [CRIT] zap_io.c:804 zap_channel_open_any() All
>>>>         
>>> circuits are busy.
>>>       
>>>> 2009-01-12 10:20:01 [ERR] mod_openzap.c:910  
>>>> channel_outgoing_channel()
>>>>         
>>> No channels available
>>>       
>>>> 2009-01-12 10:20:01 [ERR] switch_ivr_originate.c:926
>>>>         
>>> switch_ivr_originate() Cannot create outgoing channel of type  
>>> [openzap] cause:
>>> [DESTINATION_OUT_OF_ORDER]
>>>       
>>>> What's wrong? Do you need any configurations?
>>>>
>>>> Thanks!
>>>> Best Regards, Curly
>>>>
>>>>
>>>>
>>>>         
>>> _______________________________________________
>>> Freeswitch-users mailing list
>>> Freeswitch-users@lists.freeswitch.org
>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>> http://www.freeswitch.org
>>>       
>> _______________________________________________
>> Freeswitch-users mailing list
>> Freeswitch-users@lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>     
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users@lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>

curly2009＠gmx.de

Peter P GMX

"Franziska Röhler"

curly2009＠gmx.de

Michael S Collins

Peter P GMX

tags

participants (4)