I use q931 too. openzap.conf.xml <configuration name="openzap.conf" description="OpenZAP Configuration"> <settings> <param name="debug" value="0"/> <!--<param name="hold-music" value="$${moh_uri}"/>--> <!--<param name="enable-analog-option" value="call-swap"/>--> <!--<param name="enable-analog-option" value="3-way"/>--> </settings> <!-- one entry here per openzap span --> <pri_spans> <span id="1"> <param name="mode" value="user"/> <param name="dialect" value="q931"/> <param name="dialplan" value="XML"/> <param name="context" value="default"/> </span> </pri_spans> </configuration> openzap.conf [span zt] name => OpenZap number => 1 trunk_type => e1 b-channel => 1-15, 17-31 d-channel => 16 cat /proc/zaptel/* Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4 RECOVERING 1 WCT1/0/1 Clear (In use) RED 2 WCT1/0/2 Clear (In use) RED 3 WCT1/0/3 Clear (In use) RED 4 WCT1/0/4 Clear (In use) RED 5 WCT1/0/5 Clear (In use) RED 6 WCT1/0/6 Clear (In use) RED 7 WCT1/0/7 Clear (In use) RED 8 WCT1/0/8 Clear (In use) RED 9 WCT1/0/9 Clear (In use) RED 10 WCT1/0/10 Clear (In use) RED 11 WCT1/0/11 Clear (In use) RED 12 WCT1/0/12 Clear (In use) RED 13 WCT1/0/13 Clear (In use) RED 14 WCT1/0/14 Clear (In use) RED 15 WCT1/0/15 Clear (In use) RED 16 WCT1/0/16 HDLCFCS (In use) RED 17 WCT1/0/17 Clear (In use) RED 18 WCT1/0/18 Clear (In use) RED 19 WCT1/0/19 Clear (In use) RED 20 WCT1/0/20 Clear (In use) RED 21 WCT1/0/21 Clear (In use) RED 22 WCT1/0/22 Clear (In use) RED 23 WCT1/0/23 Clear (In use) RED 24 WCT1/0/24 Clear (In use) RED 25 WCT1/0/25 Clear (In use) RED 26 WCT1/0/26 Clear (In use) RED 27 WCT1/0/27 Clear (In use) RD 28 WCT1/0/28 Clear (In use) RED 29 WCT1/0/29 Clear (In use) RED 30 WCT1/0/30 Clear (In use) RED 31 WCT1/0/31 Clear (In use) RED Why is it RED? zttool shows no alarms (ok) and ztfcg -vv shows that 31 Channels to configure.
I had the same problem a while ago with German PRI lines (S2M).
Do you have <param name="dialect" value="q931"/> in your openzap.conf.xml?
In older Versions of openzap I used euro, in newer releases this didn't work any more, so I used q931.
If this is not successfull,
can you post your openzap.conf.xml and openzap.xml and the output of cat /proc/zaptel/*
Best regards Peter
curly2009@gmx.de schrieb:
Hello,
I'm a newbie in FS.
I installed and configure Openzap and Zaptel. I have a PRI Digium Wildcard TE110P.
When I call a number then I get an Error!
2009-01-12 10:20:01 [CRIT] zap_io.c:804 zap_channel_open_any() All circuits are busy. 2009-01-12 10:20:01 [ERR] mod_openzap.c:910 channel_outgoing_channel() No channels available 2009-01-12 10:20:01 [ERR] switch_ivr_originate.c:926 switch_ivr_originate() Cannot create outgoing channel of type [openzap] cause: [DESTINATION_OUT_OF_ORDER]
What's wrong? Do you need any configurations?
Thanks! Best Regards, Curly
_______________________________________________ Freeswitch-users mailing list Freeswitch-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Psssst! Schon vom neuen GMX MultiMessenger gehört? Der kann`s mit allen: http://www.gmx.net/de/go/multimessenger