Hey, I was wondering if anyone out there in the FreeSwitch community has successfully used FXO cards (e.g. VIC2-4FXO) in a CISCO router (e.g. 2811) with FreeSwitch. Was this achieved via SIP communication between the CISCO and FreeSwitch? Any documentation out there? I can't seem to find much for FreeSwitch regarding what would need to be done on the FreeSwitch end. Regards, Oliver Schenk NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail.
2011/5/16 Schenk, Oliver <OSchenk@wnr.com.au>:
Hey,
Hello,
I was wondering if anyone out there in the FreeSwitch community has successfully used FXO cards (e.g. VIC2-4FXO) in a CISCO router (e.g. 2811) with FreeSwitch.
Was this achieved via SIP communication between the CISCO and FreeSwitch?
Are you using those with CUCM currently? If yes, what is the used protocol? I f this is SCCP, I'm interrested by a network capture.
Any documentation out there? I can’t seem to find much for FreeSwitch regarding what would need to be done on the FreeSwitch end.
I don't know. Regards -- Mathieu
NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail.
Really?
I have working SIP trunks from CCME 4.3 to FS, if that's what you mean. On Mon, May 16, 2011 at 7:08 AM, Schenk, Oliver <OSchenk@wnr.com.au> wrote:
Hey,
I was wondering if anyone out there in the FreeSwitch community has successfully used FXO cards (e.g. VIC2-4FXO) in a CISCO router (e.g. 2811) with FreeSwitch.
Was this achieved via SIP communication between the CISCO and FreeSwitch?
Any documentation out there? I can’t seem to find much for FreeSwitch regarding what would need to be done on the FreeSwitch end.
Regards,
*Oliver Schenk*
NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail.
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Mathieu, CCME is runing allready inside C28XX CCME will talk to freeswitch through Sip or H.323. SCCP i'm not sure, but sip is sure. thank you On 16/05/2011 10:57, Mathieu Parent wrote:
2011/5/16 Ognjen Seslija<oseslija@gmail.com>:
I have working SIP trunks from CCME 4.3 to FS, if that's what you mean.
No ;-) I want to know the protocol used between CCME and the Cisco 2811: MGCP, H323, SCCP, SIP?
-- Meftah Tayeb inum: +883510001288000 phone: +13477595883
I think what Mathieu is saying is that since he is writing mod_skinny that it would be extremely valuable for him to see some raw network captures between the CUCM and the 2811 - assuming, of course, that they are not both running inside the 2811 as Meftah noted. In other words, in addition to the OP's issue Mathieu was asking for extra information about how the OP is currently using the FXO cards. -MC On Mon, May 16, 2011 at 5:32 AM, Meftah Tayeb <tayeb.meftah@gmail.com>wrote:
Mathieu, CCME is runing allready inside C28XX CCME will talk to freeswitch through Sip or H.323. SCCP i'm not sure, but sip is sure. thank you On 16/05/2011 10:57, Mathieu Parent wrote:
2011/5/16 Ognjen Seslija<oseslija@gmail.com>:
I have working SIP trunks from CCME 4.3 to FS, if that's what you mean.
No ;-) I want to know the protocol used between CCME and the Cisco 2811: MGCP, H323, SCCP, SIP?
-- Meftah Tayeb inum: +883510001288000 phone: +13477595883
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FYI, I am about 80% sure that sccp is only for phones or ATAs. Routers use MGCP or H.323 to talk to CCM or CUCM or CCME or whatever they are calling it today.. He appears to be running CCME on a router, so you won't get any captures as it will all be internal. From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins Sent: Monday, May 16, 2011 2:43 PM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] CISCO FXO cards with FreeSwitch I think what Mathieu is saying is that since he is writing mod_skinny that it would be extremely valuable for him to see some raw network captures between the CUCM and the 2811 - assuming, of course, that they are not both running inside the 2811 as Meftah noted. In other words, in addition to the OP's issue Mathieu was asking for extra information about how the OP is currently using the FXO cards. -MC On Mon, May 16, 2011 at 5:32 AM, Meftah Tayeb <tayeb.meftah@gmail.com> wrote: Mathieu, CCME is runing allready inside C28XX CCME will talk to freeswitch through Sip or H.323. SCCP i'm not sure, but sip is sure. thank you On 16/05/2011 10:57, Mathieu Parent wrote:
2011/5/16 Ognjen Seslija<oseslija@gmail.com>:
I have working SIP trunks from CCME 4.3 to FS, if that's what you mean.
No ;-) I want to know the protocol used between CCME and the Cisco 2811: MGCP, H323, SCCP, SIP?
-- Meftah Tayeb inum: +883510001288000 phone: +13477595883 _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
2011/5/16 Michael Collins <msc@freeswitch.org>:
I think what Mathieu is saying is that since he is writing mod_skinny that it would be extremely valuable for him to see some raw network captures between the CUCM and the 2811 - assuming, of course, that they are not both running inside the 2811 as Meftah noted. In other words, in addition to the OP's issue Mathieu was asking for extra information about how the OP is currently using the FXO cards.
Yes, this is what I meant. 2011/5/16 Peder <peder@networkoblivion.com>:
FYI, I am about 80% sure that sccp is only for phones or ATAs. Routers use MGCP or H.323 to talk to CCM or CUCM or CCME or whatever they are calling it today…. He appears to be running CCME on a router, so you won’t get any captures as it will all be internal.
What I need is an ATA capture, especially with T.38. This is not urgent, as I have a lot to do before. -- Mathieu
Cisco 2811 is the platform CCME or CUCME (whatever the name is these days) is ran on (like Call Manager appliance lite hosted on the router itself). It speaks SCCP or SIP to phones and SIP/H323/PSTN protos for trunks. I have working CCMEs with SCCP phones and SIP trunks to FS for DID routing, voicemail etc. On Mon, May 16, 2011 at 10:57 AM, Mathieu Parent <math.parent@gmail.com>wrote:
2011/5/16 Ognjen Seslija <oseslija@gmail.com>:
I have working SIP trunks from CCME 4.3 to FS, if that's what you mean.
No ;-) I want to know the protocol used between CCME and the Cisco 2811: MGCP, H323, SCCP, SIP?
-- Mathieu
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
I'm very limited in CISCO speak so I actually had to look up what CCME means. From your comments I gather that CME is something that runs inside the CISCO and not something that needs to be installed on a server? My IOS is version 12.4. Is CME something that is an add-on or something that is usually built into 2811 routers? I'm yet to purchase the FXO cards, that's why I posted this question to the mailing list in case someone would know FS will work with the hardware I mentioned. Thanks for everyone's reply. Cheers! From: Ognjen Seslija [mailto:oseslija@gmail.com] Sent: 16/05/11 16:46 To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] CISCO FXO cards with FreeSwitch I have working SIP trunks from CCME 4.3 to FS, if that's what you mean. On Mon, May 16, 2011 at 7:08 AM, Schenk, Oliver <OSchenk@wnr.com.au> wrote: Hey, I was wondering if anyone out there in the FreeSwitch community has successfully used FXO cards (e.g. VIC2-4FXO) in a CISCO router (e.g. 2811) with FreeSwitch. Was this achieved via SIP communication between the CISCO and FreeSwitch? Any documentation out there? I can't seem to find much for FreeSwitch regarding what would need to be done on the FreeSwitch end. Regards, Oliver Schenk NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail. _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail.
Any chance of some sample CISCO and/or FreeSwitch configs? You can send to my email if you can't post public. Thanks all, Oliver From: Ognjen Seslija [mailto:oseslija@gmail.com] Sent: 16/05/11 16:46 To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] CISCO FXO cards with FreeSwitch I have working SIP trunks from CCME 4.3 to FS, if that's what you mean. On Mon, May 16, 2011 at 7:08 AM, Schenk, Oliver <OSchenk@wnr.com.au> wrote: Hey, I was wondering if anyone out there in the FreeSwitch community has successfully used FXO cards (e.g. VIC2-4FXO) in a CISCO router (e.g. 2811) with FreeSwitch. Was this achieved via SIP communication between the CISCO and FreeSwitch? Any documentation out there? I can't seem to find much for FreeSwitch regarding what would need to be done on the FreeSwitch end. Regards, Oliver Schenk NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail. _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org NOTICE - This e-mail and any files transmitted with it are confidential and are only for the use of the person to whom they are addressed. If you are not the intended recipient then you have received this e-mail in error; please advise us immediately if this is the case. Any views expressed in this message are those of the individual sender, except where the sender specifically states them to be the views of WestNet Rail.
participants (6)
-
Mathieu Parent
-
Meftah Tayeb
-
Michael Collins
-
Ognjen Seslija
-
Peder
-
Schenk, Oliver