Re: [Freeswitch-users] Unable to get K3765 dongle signalling using mod_gsmopen
Thank you for your reply. Can you give me a small example of usage of minicom with dongles? Baud rate, etc... Should I call only from minicom via AT commands sent to interface or use freeswitch to init the call and only sniff the interface with minicom. Sorry if is noob question but I never tryed those low level commands. -- Best regards, Fiftyz -------- Original message -------- From: Dmitry Lysenko <dvl36.ripe.nick@gmail.com> Date: 12/06/2013 00:01 (GMT+02:00) To: FreeSWITCH Users Help <freeswitch-users@lists.freeswitch.org> Subject: Re: [Freeswitch-users] Unable to get K3765 dongle signalling using mod_gsmopen Hi!
I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling.
You should try other ttyUSBx. One of ttyUSBx used for commands only, but another for commands AND signalling too. You can open ttyUSBx with minicom and make call to number of SIM card inserted to modem. If you will see RING you will find "right" serial port. Best wishes, Dmitry. 2013/6/11 Silviu CHINGARU <silviuchingaru@gmail.com> Hi, I'm trying to make mod_gsmopen work with my testing freeswitch. I have the following setup: K3765 Huawei dongle Freeswitch 1.2.9 with mod_gsmopen I setup a gateway using gsmopen.conf.xml (see attached) and an extension in dialplan. I've set consolelog 9 and I'm able to make call via mod_gsmopen from any switch phone, but the signaling is not working. So when I answer to mobile called by gsmopen module, sip phone is still displaying "Conecting...", I can talk to mobile phone via sip phone and reverse but when I close the conversation from mobile side is still "Conecting...". In console I don't see any signaling from gsmopen like ringing, answered and so on. I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling. Also the audio interface is ok because I have audio both sides (via Early Media because the call is never signaled as answered). I've attached: - reload.log (output from freeswitch when I type reload mod_gsmopen) - call.log (output from freeswitch when I init the call via mod_gsmopen) - gsmopen.conf.xml (I've changed / masked context, ip and phone number for privacy) I've used this dongle also with chan_dongle in asterisk and was working fine but on freeswitch I'm unable to configure it. Please help, I don't even know what to read! What could be the problem, what is wrong? How can I figure out what is wrong? Thank you very much for your time! Best regards, Fiftyz _________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
I personally use picocom: #picocom -b 115200 /dev/ttyUSBx You should be root or make sudo. Only sniff the interface for "RING", when you calling to modem. Dmitry. 2013/6/12 Silviu CHINGARU <silviuchingaru@gmail.com>
Thank you for your reply.
Can you give me a small example of usage of minicom with dongles? Baud rate, etc...
Should I call only from minicom via AT commands sent to interface or use freeswitch to init the call and only sniff the interface with minicom.
Sorry if is noob question but I never tryed those low level commands.
-- Best regards, Fiftyz
-------- Original message -------- From: Dmitry Lysenko <dvl36.ripe.nick@gmail.com> Date: 12/06/2013 00:01 (GMT+02:00) To: FreeSWITCH Users Help <freeswitch-users@lists.freeswitch.org> Subject: Re: [Freeswitch-users] Unable to get K3765 dongle signalling using mod_gsmopen
Hi!
I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling.
You should try other ttyUSBx. One of ttyUSBx used for commands only, but another for commands AND signalling too. You can open ttyUSBx with minicom and make call to number of SIM card inserted to modem. If you will see RING you will find "right" serial port.
Best wishes, Dmitry.
2013/6/11 Silviu CHINGARU <silviuchingaru@gmail.com>
Hi,
I'm trying to make mod_gsmopen work with my testing freeswitch. I have the following setup: K3765 Huawei dongle Freeswitch 1.2.9 with mod_gsmopen
I setup a gateway using gsmopen.conf.xml (see attached) and an extension in dialplan. I've set consolelog 9 and I'm able to make call via mod_gsmopen from any switch phone, but the signaling is not working. So when I answer to mobile called by gsmopen module, sip phone is still displaying "Conecting...", I can talk to mobile phone via sip phone and reverse but when I close the conversation from mobile side is still "Conecting...".
In console I don't see any signaling from gsmopen like ringing, answered and so on.
I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling. Also the audio interface is ok because I have audio both sides (via Early Media because the call is never signaled as answered).
I've attached: - reload.log (output from freeswitch when I type reload mod_gsmopen) - call.log (output from freeswitch when I init the call via mod_gsmopen) - gsmopen.conf.xml (I've changed / masked context, ip and phone number for privacy)
I've used this dongle also with chan_dongle in asterisk and was working fine but on freeswitch I'm unable to configure it.
Please help, I don't even know what to read! What could be the problem, what is wrong? How can I figure out what is wrong? Thank you very much for your time!
Best regards, Fiftyz
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Waw is working. Thank you very much! For everyone else that has the same problem: 1) Connect to minicom by typing minicom -s 2) Edit serial settings and select /dev/ttyUSBx, save changes and select Exit (be carefull NOT Exit minicom) 3) Dialin the dongle number 4) - If you've got RING that is the right interface to use in controldevice_name like: <param name="controldevice_name" value="/dev/ttyUSB15"/> - If not repeat steps above until you get RING For controldevice_audio_name make a call after you find control interface and check if there is audio, if not is the other remaining tty. This info should be putted to the wiki. Best regards, Fiftyz On 12.06.2013 00:40, Dmitry Lysenko wrote:
I personally use picocom:
#picocom -b 115200 /dev/ttyUSBx
You should be root or make sudo.
Only sniff the interface for "RING", when you calling to modem.
Dmitry.
2013/6/12 Silviu CHINGARU <silviuchingaru@gmail.com <mailto:silviuchingaru@gmail.com>>
Thank you for your reply.
Can you give me a small example of usage of minicom with dongles? Baud rate, etc...
Should I call only from minicom via AT commands sent to interface or use freeswitch to init the call and only sniff the interface with minicom.
Sorry if is noob question but I never tryed those low level commands.
-- Best regards, Fiftyz
-------- Original message -------- From: Dmitry Lysenko <dvl36.ripe.nick@gmail.com <mailto:dvl36.ripe.nick@gmail.com>> Date: 12/06/2013 00:01 (GMT+02:00) To: FreeSWITCH Users Help <freeswitch-users@lists.freeswitch.org <mailto:freeswitch-users@lists.freeswitch.org>> Subject: Re: [Freeswitch-users] Unable to get K3765 dongle signalling using mod_gsmopen
Hi! > I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling.
You should try other ttyUSBx. One of ttyUSBx used for commands only, but another for commands AND signalling too. You can open ttyUSBx with minicom and make call to number of SIM card inserted to modem. If you will see RING you will find "right" serial port.
Best wishes, Dmitry.
2013/6/11 Silviu CHINGARU <silviuchingaru@gmail.com <mailto:silviuchingaru@gmail.com>>
Hi,
I'm trying to make mod_gsmopen work with my testing freeswitch. I have the following setup: K3765 Huawei dongle Freeswitch 1.2.9 with mod_gsmopen
I setup a gateway using gsmopen.conf.xml (see attached) and an extension in dialplan. I've set consolelog 9 and I'm able to make call via mod_gsmopen from any switch phone, but the signaling is not working. So when I answer to mobile called by gsmopen module, sip phone is still displaying "Conecting...", I can talk to mobile phone via sip phone and reverse but when I close the conversation from mobile side is still "Conecting...".
In console I don't see any signaling from gsmopen like ringing, answered and so on.
I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling. Also the audio interface is ok because I have audio both sides (via Early Media because the call is never signaled as answered).
I've attached: - reload.log (output from freeswitch when I type reload mod_gsmopen) - call.log (output from freeswitch when I init the call via mod_gsmopen) - gsmopen.conf.xml (I've changed / masked context, ip and phone number for privacy)
I've used this dongle also with chan_dongle in asterisk and was working fine but on freeswitch I'm unable to configure it.
Please help, I don't even know what to read! What could be the problem, what is wrong? How can I figure out what is wrong? Thank you very much for your time!
Best regards, Fiftyz
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org <mailto:consulting@freeswitch.org> http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org <mailto:consulting@freeswitch.org> http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
participants (2)
-
Dmitry Lysenko
-
Silviu CHINGARU