A great job that is. Ussd is becoming more and more widespread. I already have some ideas about it. On Feb 10, 2013 12:40 PM, "Giovanni Maruzzelli" <gmaruzz@gmail.com> wrote:

On Sun, Feb 10, 2013 at 6:10 AM, Yuriy Ostapchuk <yura407@gmail.com> wrot

...

Hi, I've submitted a patch that implements USSD messaging support. (useful for checking and refilling account balance and other provider-specific usage)

Here is the JIRA ticket: http://jira.freeswitch.org/browse/FS-5078

If this feature is considered useful, I would appreciate if it's integrated in git.

Thanks Yuriy, I'll have a look into it asap next week.

Thanks again, yes is considered useful and grateful received.

-giovanni

-- Sincerely,

Giovanni Maruzzelli Cell : +39-347-2665618

_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com

FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com

Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com

FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org

Hi!

I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling.

You should try other ttyUSBx. One of ttyUSBx used for commands only, but another for commands AND signalling too. You can open ttyUSBx with minicom and make call to number of SIM card inserted to modem. If you will see RING you will find "right" serial port. Best wishes, Dmitry. 2013/6/11 Silviu CHINGARU <silviuchingaru@gmail.com>

Hi,

I'm trying to make mod_gsmopen work with my testing freeswitch. I have the following setup: K3765 Huawei dongle Freeswitch 1.2.9 with mod_gsmopen

I setup a gateway using gsmopen.conf.xml (see attached) and an extension in dialplan. I've set consolelog 9 and I'm able to make call via mod_gsmopen from any switch phone, but the signaling is not working. So when I answer to mobile called by gsmopen module, sip phone is still displaying "Conecting...", I can talk to mobile phone via sip phone and reverse but when I close the conversation from mobile side is still "Conecting...".

In console I don't see any signaling from gsmopen like ringing, answered and so on.

I think the serial interface is ok because I can send AT commands to init the call but I don't get any signaling. Also the audio interface is ok because I have audio both sides (via Early Media because the call is never signaled as answered).

I've attached: - reload.log (output from freeswitch when I type reload mod_gsmopen) - call.log (output from freeswitch when I init the call via mod_gsmopen) - gsmopen.conf.xml (I've changed / masked context, ip and phone number for privacy)

I've used this dongle also with chan_dongle in asterisk and was working fine but on freeswitch I'm unable to configure it.

Please help, I don't even know what to read! What could be the problem, what is wrong? How can I figure out what is wrong? Thank you very much for your time!

Best regards, Fiftyz

_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com

FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com

Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com

FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org