Thanks Tom for the help, but I'm still getting an error when typing "reload mod_openzap" in the Freeswitch console (Actually, two errors: "ozmod_zt.c:Cannot open control device /dev/dahdi/ctl: Permission denied", followed by "zap_io.c failure creating span, no such type 'zt'" which could be a syntax error of mine in openzap.conf and/or openzap.conf.xml). Here are the outputs: ============================================ # dahdi_scan [1] active=yes alarms=OK description=Wildcard TDM400P REV E/F Board 5 name=WCTDM/4 manufacturer=Digium devicetype=Wildcard TDM400P REV E/F location=PCI Bus 03 Slot 01 basechan=1 totchans=4 irq=20 type=analog port=1,FXO port=2,none port=3,none port=4,none ============================================ # /etc/init.d/dahdi status ### Span 1: WCTDM/4 "Wildcard TDM400P REV E/F Board 5" (MASTER) 1 FXO FXSKS (SWEC: MG2) RED 2 EMPTY 3 EMPTY 4 EMPTY ============================================ # cat /usr/local/freeswitch/conf/zt.conf [defaults] codec_ms => 20 wink_ms => 150 flash_ms => 750 echo_cancel_level => 64 rxgain => 0.0 txgain => 0.0 ============================================ # cat /usr/local/freeswitch/conf/openzap.conf [span zt FXO] name => OpenZAP #number => 1 fxo-channel => 1 ============================================ # cat /usr/local/freeswitch/conf/autoload_configs/openzap.conf.xml <configuration name="openzap.conf" description="OpenZAP Configuration"> <settings> <!----> <!----> <!----> </settings> <pri_spans> <!-- Log Levels: none, alert, crit, err, warning, notice, info, debug --> </pri_spans> <!-- one entry here per openzap span --> <analog_spans> <!--span id="1"--> <!--span id="zt"--> <!----> <!----> <!----> <!-- regex to stop dialing when it matches --> <!----> <!-- regex to stop dialing when it does not match --> <!----> </analog_spans> </configuration> ============================================ # cat /usr/local/freeswitch/conf/autoload_configs/modules.conf.xml <configuration name="modules.conf" description="Modules"> <modules> [...] <load module="mod_openzap"/> [...] ============================================ #fs_cli freeswitch@internal> reload mod_openzap -ERR unloading module [No such module!] -ERR loading module [module load file routine returned an error] freeswitch@internal> 2010-05-28 17:13:17.830127 [DEBUG] zap_config.c:56 Configuration file is /usr/local/freeswitch/conf/modules.conf. 2010-05-28 17:13:17.830127 [NOTICE] zap_io.c:3057 Modules configured: 1 2010-05-28 17:13:17.830127 [DEBUG] zap_config.c:56 Configuration file is /usr/local/freeswitch/conf/openzap.conf. 2010-05-28 17:13:17.830127 [DEBUG] zap_io.c:2587 found config for span 2010-05-28 17:13:17.831145 [NOTICE] ozmod_zt.c:1185 Using DAHDI control device 2010-05-28 17:13:17.831145 [ERR] ozmod_zt.c:1194 Cannot open control device /dev/dahdi/ctl: Permission denied 2010-05-28 17:13:17.831145 [ERR] zap_io.c:2856 Error loading /usr/local/freeswitch/mod/ozmod_zt.so 2010-05-28 17:13:17.831145 [ERR] zap_io.c:2901 Unloading /usr/local/freeswitch/mod/ozmod_zt.so 2010-05-28 17:13:17.831145 [CRIT] zap_io.c:2610 failure creating span, no such type 'zt' 2010-05-28 17:13:17.831145 [INFO] zap_io.c:2782 Configured 0 channel(s) 2010-05-28 17:13:17.831145 [ERR] zap_io.c:3065 No modules configured! 2010-05-28 17:13:17.831145 [ERR] mod_openzap.c:3331 Error loading OpenZAP 2010-05-28 17:13:17.831145 [CRIT] switch_loadable_module.c:882 Error Loading module /usr/local/freeswitch/mod/mod_openzap.so **Module load routine returned an error** ============================================ Has someone already seen this "/dev/dahdi/ctl: Permission denied" error? Thank you. -- View this message in context: http://freeswitch-users.2379917.n2.nabble.com/Installing-OpenZap-tp5111050p5... Sent from the freeswitch-users mailing list archive at Nabble.com.