:) that was the first thing I did, but I get nothing; no keep alive packets. in the logfile at startup I see: 2010-10-26 10:19:45.484258 [INFO] switch_nat.c:410 Scanning for NAT 2010-10-26 10:19:45.485991 [DEBUG] switch_nat.c:167 Checking for PMP 1/5 2010-10-26 10:19:45.488575 [INFO] switch_nat.c:423 NAT detected type: pmp, ExtIP: '203.xxx.xxx.xxx' 2010-10-26 10:19:45.490683 [DEBUG] switch_nat.c:256 NAT thread configured 2010-10-26 10:19:45.492180 [DEBUG] switch_nat.c:267 NAT thread started And nat_map status shows me which ports have been forwarded and the external ip address (which is sometimes wrong). I also see this in the router gui. But I never see the keep alive packets. On Tue, Oct 26, 2010 at 3:13 PM, Rupa Schomaker <rupa@rupa.com> wrote:
Just turn up console logging to level 7.
/log 7 if using fs_cli
On Mon, Oct 25, 2010 at 6:53 PM, Mark Campbell-Smith < mcampbellsmith@gmail.com> wrote:
Hi!
How do I enable debugging to get the UPnP keep alive packets?
Thanks!
On Tue, Oct 26, 2010 at 1:15 AM, Rupa Schomaker <rupa@rupa.com> wrote:
I need the debug logging from the upnp stuff. It should look something like:
+OK log level 7 [7] freeswitch@internal> 2010-10-25 09:13:59.926861 [DEBUG] switch_nat.c:299 got UPnP keep alive packet: NOTIFY * HTTP/1.1 HOST:239.255.255.250:1900 Cache-Control:max-age=60 Location:http://192.168.1.1:5000/rootDesc.xml Server: Tomato UPnP/1.0 MiniUPnPd/1.4 NT:urn:schemas-upnp-org:service:WANIPConnection:1
USN:uuid:00000000-0000-0000-0000-000000000000::urn:schemas-upnp-org:service:WANIPConnection:1 NTS:ssdp:alive
I also run tomato and haven't had trouble with the upnp support so at least we have that part working.
You should see the above keepalive appear periodically every 30s or so. You should see another set of messages when you terminate the DSL connection and when that dsl connection comes back online.
On Sat, Oct 23, 2010 at 5:36 PM, Mark Campbell-Smith < mcampbellsmith@gmail.com> wrote:
Hi!
The router is a ASUS router but it is running the tomato firmware which runs miniupnd.
In the debug I see the message: 2010-10-24 08:02:59.178918 [DEBUG] sofia.c:956 nua_i_outbound: unknown event 8: 101 NAT detected
This is what I see below. I hope I enabled all debug messages. I thought I saw some xml type messages earlier, but not sure how I enabled them.
nta_outgoing: RTT is 67.958 ms outbound(0xb6e07c00): NAT binding changed: [210.xx.xxx.xx]:5080 != [58.xxx.xx.xx]:5080 nua(0xb6e07c00): event i_outbound 102 NAT binding changed nua: nua_application_event: entering 2010-10-24 09:05:08.849525 [DEBUG] sofia.c:956 nua_i_outbound: unknown event 8: 102 NAT binding changed
On Sun, Oct 24, 2010 at 1:08 AM, Rupa Schomaker <rupa@rupa.com> wrote:
btw: what router are you using?
On Sat, Oct 23, 2010 at 9:06 AM, Rupa Schomaker <rupa@rupa.com> wrote:
In a upnp config, FS is depending on the router to notify it of the ip address change. It is possible the upnp message(s) aren't formatted as expected. If you turn on debug logging you'll get the upnp messages on the console. If you can pastebin the capture of those while dropping and restarting the dsl connection I can maybe see if there is something obvious going on. The debug should also have messages related to the processing of those upnp messages.
On Sat, Oct 23, 2010 at 7:04 AM, Mark Campbell-Smith < mcampbellsmith@gmail.com> wrote:
> HI! > > I know this question must have been answered 100's of times.... > > My adsl is a bit dodgy at the moment and tends to go up and down; > which means I get assigned a new ip address from my ISP. FS is nat'd behind > a upnp capable router. > > The problem is that FS does not seem to be detecting the change. > For both the internal and external profile, I have auto-nat setup, and I > have tried stun and host settings in vars.conf. When I issue a nat_map > status I see my old IP address, and if I then issue a nat_map reinit, I see > the new public IP address. How can I get this to be automatic? > > Also the public IP address shown in the nat_map status is not the > same as shown in the sofia profile internal/external printouts. Why is > this? > > I'm sure this is configuration, just not sure what to change. > > Thanks! > > _______________________________________________ > FreeSWITCH-users mailing list > FreeSWITCH-users@lists.freeswitch.org > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users > UNSUBSCRIBE: > http://lists.freeswitch.org/mailman/options/freeswitch-users > http://www.freeswitch.org > >
-- -Rupa
-- -Rupa
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- -Rupa
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- -Rupa
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org