which pri stack is this? Mike On May 11, 2010, at 1:35 PM, Ron McLeod wrote:
Tony sent me a Q.931 trace off-list and I thought I would post it here any case anyone has seen this before.
The telco side is including a Signal IE in the SETUP message. I’m not sure what this means – that the telco will play alerting pattern 0 back to the CPE unless otherwise instructed?
Other things in the trace: * SETUP is sent again because the dial plan was executing sleep() before anything triggered a CALL PROCEEDING. * The switch PRI stack is reflecting back the Signal IE in the ALERTING, CONNECT, and RELEASE messages and the telco complains that the IE is not supported.
RX [08 02 32 11 05 a1 04 03 80 90 a2 18 03 a1 83 97 34 01 40 6c 0a 00 81 XX XX XX XX 30 36 39 34 70 05 80 36 37 30 30] Message Type: [05] SETUP IE: [a1] Sending Complete IE: [04] Bearer Capability IE: [18] Channel identification IE: [34] Signal - Alerting on – pattern 0 IE: [6c] Calling party number - TON unknown/NPI unknown/Presentation allowed/User-provided, not screened/XXXX0694 IE: [70] Called party number - TON unknown/NPI unknown/6700
RX [08 02 32 11 05 a1 04 03 80 90 a2 18 03 a1 83 97 34 01 40 6c 0a 00 81 XX XX XX XX 30 36 39 34 70 05 80 36 37 30 30] Message Type: [05] SETUP IE: [a1] Sending Complete IE: [04] Bearer Capability IE: [18] Channel identification IE: [34] Signal - Alerting on – pattern 0 IE: [6c] Calling party number - TON unknown/NPI unknown/Presentation allowed/User-provided, not screened/XXXX0694 IE: [70] Called party number - TON unknown/NPI unknown/6700
TX [08 02 b2 11 02 04 03 80 90 a2 18 03 a1 83 97] Message Type: [02] CALL PROCEEDING IE: [04] Bearer Capability IE: [18] Channel identification
TX [08 02 b2 11 01 04 03 80 90 a2 18 03 a1 83 97 34 01 40] Message Type: [01] ALERTING IE: [04] Bearer Capability IE: [18] Channel identification IE: [34] Signal - Alerting on – pattern 0
TX [08 02 b2 11 07 18 03 a1 83 97 34 01 40] Message Type: [07] CONNECT IE: [18] Channel identification IE: [34] Signal - Alerting on – pattern 0
RX [08 02 32 11 7d 08 07 82 e3 34 00 00 00 00 14 01 07] Message Type: [7d] STATUS IE: [08] Cause -- IE not implemented/Signal IE: [14] Call State -- call received
RX [08 02 32 11 7d 08 07 82 e3 34 00 00 00 00 14 01 08] Message Type: [7d] STATUS IE: [08] Cause -- IE not implemented/Signal IE: [14] Call State -- connect request
RX [08 02 32 11 0f] Message Type: [0f] CONNECT ACKNOWLEDGE
RX [08 02 32 11 45 08 02 82 90] Message Type: [45] DISCONNECT IE: [08] Cause -- Normal call clearing
TX [08 02 b2 11 4d 34 01 40] Message Type: [4d] RELEASE IE: [34] Signal - Alerting on – pattern 0
RX [08 02 32 11 5a 08 07 82 e3 34 00 00 00 00] Message Type: [5a] RELEASE COMPLETE IE: [08] Cause -- IE not implemented/Signal
From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Anthony Minessale Sent: Monday, May 10, 2010 9:15 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] short ringback tone when answer
if ringback is not set, it would never play a tone and even if it was, it would not be played if you explicitly called answer. Try reversing the answer and the sleep in your dialplan.
On Sun, May 9, 2010 at 9:37 PM, Tony Tin <tony.tin@noahmedia.com.hk> wrote: Hi Peter,
Thanks for your reply.
The other end is the Telco, I've confirmed with them that they don't play the tone for us, also I got the Asterisk install in the same box, it doesn't play the tone. The tone is played exactly when the answer function is executed, if I put sleep 10 seconds before the answer, the tone will delay 10 seconds too, any idea?
Regards, Tony
On Mon, May 10, 2010 at 2:33 AM, Peter Olsson <peter.olsson@visionutveckling.se> wrote: The equipment connected in the other en of the T1 is probably playing these tones for you, 500ms is probably the time it takes for the called to be connected successfully.
/Peter ________________________________________ Från: freeswitch-users-bounces@lists.freeswitch.org [freeswitch-users-bounces@lists.freeswitch.org] för Tony Tin [tony.tin@noahmedia.com.hk] Skickat: den 9 maj 2010 15:16 Till: freeswitch-users@lists.freeswitch.org Ämne: [Freeswitch-users] short ringback tone when answer
Hi All,
I've just setup a new IVRS with FreeSwitch and a Digium TE220 card (which is connected to a 4ess T1). Every thing works fine so far except one little problem that annoys me. Every time I dial in the ivrs, there is a very short (0.5 second) ringback tone exactly while the "<action application="answer"/>" line is executed in the dial plan. I want to disable this ringback tone because the ivrs will answer the call immediately, the ringback tone is really unnecessary in this case, but I fail to do that. I try to set the variable "ringback" to change the ringback tone, it's also not working. Could anyone please help.
I'm using the native pri stack. The default.xml containts only below lines, and attached is the log file.
<extension name="testing"> <condition field="destination_number" expression="^(6.*)$"> <action application="sleep" data="3000"/> <action application="answer"/> <action application="sleep" data="3000"/> </condition> </extension>
Regards, Tony
!DSPAM:4be6f37432931620317181!
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Anthony Minessale II
FreeSWITCH http://www.freeswitch.org/ ClueCon http://www.cluecon.com/ Twitter: http://twitter.com/FreeSWITCH_wire
AIM: anthm MSN:anthony_minessale@hotmail.com GTALK/JABBER/PAYPAL:anthony.minessale@gmail.com IRC: irc.freenode.net #freeswitch
FreeSWITCH Developer Conference sip:888@conference.freeswitch.org googletalk:conf+888@conference.freeswitch.org pstn:+19193869900 _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org