You might want to check with sangoma support or their wiki on this if its not well documented on our wiki On Wednesday, June 10, 2015, Matt Broad <matt@inveroak.com> wrote:
Hi Vallimamod,
thanks for your response. regarding the hunting order.
With regards to the group, I can't see in any of the files that group is mentioned or referenced other than, as you say, freetdm.conf. I have created the conf file manually and gave the spans different names than wp1 and wp2 but this causes the mod_freetdm to not load correctly stating that the spans cannot be found. I am not sure what I am doing wrong, I am happy to have the spans named as they are by wancfg_fs but I would like them to be grouped
thanks Matt
On 09/06/2015 12:10, Vallimamod Abdullah wrote:
Hi,
- the “a” means isdn channel hunting order: “a” seeks for the first lowest numbered channel available and “A”, for the first highest numbered (i.e. start seeking from the end.) It is advisable to *not* use the same order as your telco to avoid glare conditions.
- for the group, I don’t know if there is another place for isdn but for ss7, I declare it only on freetdm.conf. Make sure the span name is the same in autoload_configs/freetdm.conf.xml:
<sangoma_pri_spans> <span name="wp1" cfgprofile="my_pri_te_e1_1"> ...
Here the “name” must be the same as in freetdm.conf.
Hope this helps!
Best regards, Vallimamod .
On 09 Jun 2015, at 09:45, Matt Broad <matt@inveroak.com <javascript:;>> wrote:
HI,
I have a sangoma A102 card and have configured it using the Freetdm example (https://freeswitch.org/confluence/display/FREESWITCH/FreeTDM).
I can make calls out using both spans, but I have a couple of questions:
in the below CLI command, what does the "a" refer to? "originate freetdm/1/a/0123412345 &conference(123)"
secondly, I will be using both ports to make outbound calls only and I am trying to add both spans to a group so that I can send calls out over the next available line. I have the following as my freetdm.conf
[span wanpipe wp1] trunk_type => e1 group=PSTN b-channel => 1:1-15 b-channel => 1:17-31 d-channel => 1:16
[span wanpipe wp2] trunk_type => e1 group=PSTN b-channel => 2:1-15 b-channel => 2:17-31 d-channel => 2:16
When I try to make a call out using "originate freetdm/PSTN/a/0123412345 &conference(123)" I get the error "[ERR] mod_freetdm.c:1390 Missing ftdm span or group: PSTN"
Any ideas why this would be? Do I need to declare the group elsewhere? I have tried configuring the card using "wancfg_fs" and doing it manually but both result in the error (though wancfg_fs requires the group to contain a number)
thanks Matt
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org <javascript:;> http://www.freeswitchsolutions.com
Official FreeSWITCH Sites http://www.freeswitch.org http://confluence.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <javascript:;> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org <javascript:;> http://www.freeswitchsolutions.com
Official FreeSWITCH Sites http://www.freeswitch.org http://confluence.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <javascript:;> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org