I can't point you to any great source of documentation other than the FreeTDM Wiki pages which cover the configuration reasonably well as long as you understand the concepts of FXO and FXS. I too found it required a bit of studying. The key thing I think to remember is that FreeTDM justs talks to a hardware abstraction layer eg. dahdi. You need to ensure that this hardware abstraction layer is in place and working. In the case of dahdi I had to download and build the drivers. There are a set of tools to ensure that the hardware is seen correctly and is available via the dahdi interfaces. Once you have that working then it is just the FreeTDM config files (two I believe) that need to configured for the FreeTDM module to run correctly and make the analog "channels" available to your dialplans. The syntax for referencing the channels I had to guess at since I couldn't find any ultimate reference for that with FreeTDM examples. HTH Shane On Tue, Mar 20, 2012 at 10:20 PM, Fu Jiantao <fuji246@gmail.com> wrote:
Thanks Moises!
So span is a logic concept, while channel is corresponding to the port(fxo or fxs) on the card, am i right?
I'm new to the freeswitch and asterisk world, and found the most difficult part is relating to the PSTN, I'm not familiar with PSTN, and I've read asterisk book and freeswitch book, and learn the basic of PSTN, but that seems not enough, for example, I found I can't figure out how to use FreeTDM, little are relating to this topic, is there any good references on this topic?
I'm trying to port the io module chan_fx<http://www.asteriskwin32.com/chan_fx.php>in asterisk win32into freeTDM, but I found I need to know more about the above topic.
2012/3/20 Moises Silva <moises.silva@gmail.com>
On Sun, Mar 18, 2012 at 10:58 AM, Jeromy <fuji246@gmail.com> wrote:
I'm trying to convert from Asterisk to Freeswitch, and have a question about spans.
I read the freetdm configuration example for TDM400 and am wondering what exactly is a span.
I have 2 TDM400P cards in my computer, one card has 2 FXS modules for connecting analog phones. The other card has 3 FXO modules for connecting to 3 PSTN trunk lines.
# lsdahdi ### Span 1: WCTDM/4 "Wildcard TDM400P REV I Board 5" 1 FXS FXOKS (In use) (EC: OSLEC - INACTIVE) 2 FXS FXOKS (In use) (EC: OSLEC - INACTIVE) 3 unknown Reserved 4 unknown Reserved ### Span 2: WCTDM/4 "Wildcard TDM400P REV I Board 5" (MASTER) 5 FXO FXSKS (In use) (EC: OSLEC - INACTIVE) 6 FXO FXSKS (In use) (EC: OSLEC - INACTIVE) 7 FXO FXSKS (In use) (EC: OSLEC - INACTIVE) 8 unknown Reserved
Do I configure freetdm as in the example for TDM400 with separate spans for each module like the following? or should I have just two spans as shown by lsdahsi? Thanks.
Hi Jeremy
Do you find the answer to this question?
I'm also very confuse on the span and channel in both asterisk and freeswitch, and I've found little explaination on this.
" A span is a logical unit that represents a group of channels. With digital telephony, a span usually represents a physical port on the card. If the system has only one such card with a single port, so it is referred to as span 1. "
Could anyone help on this?
At the very least you need 2 freetdm span configurations because you cannot mix FXS and FXO channels in the same FreeTDM logical span.
http://wiki.freeswitch.org/wiki/FreeTDM#DAHDI_mode
For the given hardware output, I'd simply create 2 spans, one for all the fxo channels and one for all the fxs channels.
*Moises Silva **Manager, Software Engineering***
msilva@sangoma.com
Sangoma Technologies
100 Renfrew Drive, Suite 100, Markham, ON L3R 9R6 Canada
t. +1 800 388 2475 (N. America)
t. +1 905 474 1990 x128
f. +1 905 474 9223
**<http://www.sangoma.com/contact?utm_source=signature&utm_medium=email&utm_campaign=email+signatures>
Products<http://sangoma.com/products?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Solutions<http://sangoma.com/solutions?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Events<http://sangoma.com/about_us/events?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Contact<http://www.sangoma.com/contact?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Wiki<http://wiki.sangoma.com/?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Facebook<http://www.facebook.com/pages/Sangoma-VoIP-Cards/43578453335?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Twitter<http://www.twitter.com/sangoma?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures>`| | YouTube<http://www.youtube.com/sangomatechnologies?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures>
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_________________________________________________________________________ Professional FreeSWITCH Consulting Services: consulting@freeswitch.org http://www.freeswitchsolutions.com
FreeSWITCH-powered IP PBX: The CudaTel Communication Server http://www.cudatel.com
Official FreeSWITCH Sites http://www.freeswitch.org http://wiki.freeswitch.org http://www.cluecon.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Paragon Electronic Design Ltd L6 Crest House 92 Queens Drive P0 Box 30449 Lower Hutt 5040 +64 4 5703870 Extn 875 +64 21 608919 (mobile) "Solving your problems with the right technology"