Thank you for the quick response. It looks like monitor_early_media_fail should do what I need (thanks for the suggestion!) but I can't seem to make it work. See below for my uneducated best guess why. In my case the failure conditions from the GSM side are handled out-of-band by SIP. That leaves only one failure condition I need to listen for in early media (the Panasonic far-end hang up on FXO) which can successfully be detected with: <action application="tone_detect" data="busy-pan 350,440 r 0 hangup> This results in the following log entries: [DEBUG] switch_ivr_async.c:2072 Adding tone spec 350,440 index 0 hits 1 [DEBUG] switch_core_media_bug.c:360 Attaching BUG to FreeTDM/4:1/ Translating tone_detect to monitor_early_media_fail I tried the following: <action application="set" data="result=${fifo_member(add fifo_helpdesk {fifo_member_wait=nowait,ignore_early_media=true,monitor_early_media_fail=bu sy-pan:1:350+440}sofia/internal/${caller_id_number}@192.168.3.11:5060)}"/> This results in the following relevant log entries: [DEBUG] switch_channel.c:2444 (sofia/internal/1876??????@192.168.3.11:5060) Callstate Change RINGING -> EARLY [DEBUG] switch_ivr_async.c:2072 Adding tone spec 350,440 index 0 hits 1 [DEBUG] switch_core_media_bug.c:360 Attaching BUG to sofia/internal/1??????7693@192.168.3.11:5060 So Freeswitch is listening for the right tones (tone_spec present and identical to the one used in tone_detect approach) but it isn't detecting them. The obvious difference is in the BUG attachment. Is it possible that BUG isn't listening to the right (A) leg in the case of monitor_early_media_fail? Or is this too easy? :-) Cheers, -Slim -- Jeroen C. "Slim" van Gelderen _____ From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Michael Collins Sent: Sunday, October 10, 2010 19:01 To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] tone_detect vs. ignore_early_media (per leg?) Check out monitor_early_media_fail: http://wiki.freeswitch.org/wiki/Channel_Variables#monitor_early_media_fail It is a hybrid of ignoring early media and listening to early media for various conditions. In your case you'll need to play around with it. In your case you need to figure out which early media scenarios count as a "fail" and will cause processing to move on as if the call really did fail. Roll up your sleeves, you have some work to do. :) -MC On Sat, Oct 9, 2010 at 9:24 PM, Jeroen C. van Gelderen <slim@thegreek.com> wrote: Hi Guys, I have a legacy Panasonic PBX which does not support CPC/Disconnect Supervision. Calls from this PBX are sent to Freeswitch by way of DAHDI/FreeTDM FXO ports (on a Xorcom Astribank). I use tone_detect to deal with far-end hang-ups. This works fine: <!-- Detect busy tone from Panasonic --> <action application="tone_detect" data="busy 350,440 r 0 hangup 4"/> Some calls from the Panasonic PBX are put in a FIFO and from there they are sent to a SIP-to-GSM bridge (GoIP) to be terminated on one of 3 GSM phones in a round-robin fashion. The GSM bridge requires me to use "ignore_early_media=true" otherwise the caller will receive messages like "the number you are calling does not answer". When I set "ignore_early_media=true" the FIFO correctly keeps hunting for a GSM phone that is actually answered and will ignore phones that are busy, no-answer or turned off. This too works fine. The problem occurs when the two are combined as follows: Panasonic PBX --FXO--> Freeswitch --SIP--> GSM-bridge If I enable ignore_early_media then tone_detect doesn't work UNTIL one of the GSMs is answered. This is a problem when none of the GSMs are answered and the Panasonic PBX hangs up. The FXO port will stay "up" and the FIFO will keep hunting until it times out. If I don't use "ignore_early_media=true" then tone_detect works fine but then every telco message gets mistaken for an answered call and the hunting stops early. I tried changing this example line from my fifo.conf: <member timeout="30" simo="1" lag="5"> {member_wait=nowait,ignore_early_media=true}sofia/internal/1??????7701@192.1 68.3.11:5060 </member> to <member timeout="30" simo="1" lag="5"> {member_wait=nowait}[ignore_early_media=true]sofia/internal/1??????7701@192. 168.3.11:5060 </member> in a vain attempt to ignore early media on the SIP leg only. This doesn't seem to do anything however. Can anyone clue me in on what I'm missing? I've snipped the relevant configuration bits below. I have the feeling I'm missing something obvious. Cheers, -Slim ----8<----8<----8<----8<----8<---- <configuration name="fifo.conf" description="FIFO Configuration"> <settings> <param name="delete-all-outbound-member-on-startup" value="false"/> </settings> <fifos> <fifo name="cool_fifo@$${domain}" importance="0"> <member timeout="30" simo="1" lag="5"> {member_wait=nowait,ignore_early_media=true}sofia/internal/1??????7701@192.1 68.3.11:5060</member> <member timeout="30" simo="1" lag="5"> {member_wait=nowait,ignore_early_media=true}sofia/internal/1??????7693@192.1 68.3.11:5060</member> <member timeout="30" simo="1" lag="5"> {member_wait=nowait,ignore_early_media=true}sofia/internal/1??????7698@192.1 68.3.11:5060</member> </fifo> </fifos> </configuration> ----8<----8<----8<----8<----8<---- <include> <context name="pbx_test"> <extension name="test1"> <condition field="${freetdm_span_name}" expression="^span_fxo_test$"> <action application="answer"/> <!-- Detect busy tone from Panasonic --> <action application="tone_detect" data="busy 350,440 r 0 hangup 4"/> <action application="playback" data="ivr/ivr-hold_connect_call.wav"/> <action application="fifo" data="cool_fifo@$${domain} in"/> </condition> </extension> </context> </include> ----8<----8<----8<----8<----8<---- Cheers, -Slim -- Jeroen C. "Slim" van Gelderen _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org