Hi Moises, I recently added a second PRI line to my A102 and followed your instructions below (modified /etc/wanpipe/smg_pri.conf; openzap.conf as shown below) and can successfully dial out with g1, but not the recently added second line set on g2. Below is the error we get: freeswitch@otalo> originate openzap/smg_prid/a/<num>@g2 &echo 2010-06-21 19:15:59.591930 [WARNING] ozmod_sangoma_boost.c:344 TX EVENT: CALL_START:(80) [w1g1] CSid=3 Seq=4 Cn=[N/A] Cd=[9586550654] Ci=[N/A] Rdnis=[] 2010-06-21 19:15:59.624992 [WARNING] ozmod_sangoma_boost.c:1632 RX EVENT (N): CALL_START_ACK:(81) [w2g1] Rc=0 CSid=3 Seq=6 2010-06-21 19:15:59.625987 [NOTICE] switch_channel.c:675 New Channel OpenZAP/1:31/<num>@g2 [19ae26fb-f9e4-480a-9cc7-11fa91b8bb1c] 2010-06-21 19:15:59.724996 [WARNING] ozmod_sangoma_boost.c:1632 RX EVENT (N): CALL_STOPPED:(85) [w2g1] Rc=3 CSid=3 Seq=7 2010-06-21 19:15:59.724996 [NOTICE] mod_openzap.c:1935 Hangup OpenZAP/1:31/<num>@g2 [CS_CONSUME_MEDIA] [NO_ROUTE_DESTINATION] -ERR NO_ROUTE_DESTINATION Seems like a config issue, but not sure what I'm missing. Any ideas? Thanks in advance, Neil On Sun, May 16, 2010 at 10:50 AM, Moises Silva <moises.silva@gmail.com>wrote:
Hi Again Neil,
I just noticed your dial string is incorrect. The correct syntax is:
OpenZAP/<span>/<chan_code>/[number]
The span and chan code are mandatory. The number is optional ( FXS channels do not require a number, they just ring the FXO device connected to them).
The span is either a number ( span id, the id is a number assigned in the order in which the span is defined in openzap.conf ) or a span name also as specified in the [span wanpipe <span_name>] line in openzap.conf
The chan code is either a number ( for spans that support individual channel selection, boost is NOT one of them ), or a channel hunting mode, there is currently 2 modes, "a" is top down and "A" is bottom up.
So, this is a valid string for you case:
OpenZAP/smg_prid/a/<number>
In the specific case of boost in socket mode ( openzap only supports socket mode ) the number may contain @gX where X is a group ( for hunting as configured in /etc/wanpipe/smg_pri.conf). Boost signaling are a special case because the hunting for channels is not done within FreeSWITCH but in sangoma_prid binary ( in the new OpenZAP version called FreeTDM this has changed depending on configuration).
Bottom line, this should work:
OpenZAP/smg_prid/a/1234@g1
If you have g1 configured in /etc/wanpipe/smg_pri.conf
Moises Silva Senior Software Engineer Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada t. 1 905 474 1990 x 128 | e. moy@sangoma.com
On Sat, May 15, 2010 at 6:26 PM, Neil Patel <neilp@cs.stanford.edu> wrote:
Span was originally in the boost section when I got this error, so I thought I'd try it in analog and both. None work.
-Neil
On Sat, May 15, 2010 at 3:18 PM, Moises Silva <moises.silva@gmail.com>wrote:
Why do you have 2 spans in openzap.conf.xml with the same name, in both the boost and analog sections? Moises Silva Senior Software Engineer Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada t. 1 905 474 1990 x 128 | e. moy@sangoma.com
On Sat, May 15, 2010 at 3:52 PM, Neil Patel <neilp@cs.stanford.edu>wrote:
Hi All,
I am trying to dial out over my PRI, and am getting this error:
2010-05-16 01:01:21.452392 [CRIT] zap_io.c:1139 SPAN NOT DEFINED! 2010-05-16 01:01:21.452392 [ERR] mod_openzap.c:1154 No channels available 2010-05-16 01:01:21.452392 [ERR] switch_ivr_originate.c:2249 Cannot create outgoing channel of type [OpenZAP] cause: [NORMAL_CIRCUIT_CONGESTION]
This is my openzap.conf:
[span wanpipe smg_prid] name => smg_prid trunk_type =>e1 b-channel => 1:1-15 b-channel => 1:17-31 trunk_type =>e1 b-channel => 2:1-15 b-channel => 2:17-31
This is my openzap.conf.xml:
<configuration name="openzap.conf" description="OpenZAP Configuration"> <settings> <param name="debug" value="0"/>
</settings> <boost_spans> <span id="smg_prid"> <param name="dialplan" value="XML"/> <param name="context" value="default"/> </span> </boost_spans>
<analog_spans> <span id="smg_prid"> <param name="dialplan" value="XML"/> <param name="context" value="default"/>
</span> </analog_spans> </configuration>
And here is the lua code I'm using to dial out:
sessiondata = "OpenZAP/smg_prid/<num>" new_session = freeswitch.Session(sessiondata)
What am I missing here? Thanks, Neil
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org