Hello All, I seem to have an issue being able to make outbound calls via a Digium TDM2400P configured with Dahdi and FreeTDM. I searched and followed the instructions on the Freeswitch site as well as Sangoma's site but can't seem to get any further so I am hoping that someone could double check my config and provide some feedback. The test calls are being sent from a registered Jitsi softphone. I am not getting any progress tones when I send the call from FS and the call appears to hang for about 30 secs or so. When I test with Asterisk I get the progress tones so perhaps there is some issue with my config. The full log is available here: http://pastebin.freeswitch.org/21901 freeswitch@internal> ftdm dump 1 1 span_id: 1 chan_id: 1 physical_span_id: 1 physical_chan_id: 1 physical_status: ok physical_status_red: 0 physical_status_yellow: 0 physical_status_rai: 0 physical_status_blue: 0 physical_status_ais: 0 physical_status_general: 0 signaling_status: UP type: FXO state: DOWN last_state: DOWN txgain: 2.00 rxgain: 3.00 cid_date: cid_name: cid_num: ani: aniII: dnis: rdnis: cause: NONE session: (none) **** My configuration is as follows: **** ## /etc/dahdi/system.conf # Span 1: WCTDM/0 "Wildcard TDM2400P" (MASTER) fxsks=1 echocanceller=mg2,1 fxsks=2 echocanceller=mg2,2 . . <snipped> . . fxsks=23 echocanceller=mg2,23 fxsks=24 echocanceller=mg2,24 # Global data loadzone = us defaultzone = us ## /usr/local/freeswitch/conf/freetdm.conf [general] cpu_monitor => no cpu_monitoring_interval => 1000 cpu_set_alarm_threshold => 80 cpu_clear_alarm_threshold => 70 cpu_alarm_action => warn debugdtmf_directory=/var/log/freetdm.log iostats => yes [span zt myDahdiFXO] name => myDahdiFXO trunk_type => fxo analog-start-type => kewl group => grp1 txgain=2.0 rxgain=3.0 fxo-channel => 1-24 ## /usr/local/freeswitch/conf/autoload_configs/freetdm.conf.xml <configuration name="freetdm.conf" description="FreeTDM Configuration"> <settings> <param name="debug" value="0"/> <!--<param name="fail-on-error" value="no"/>--> </settings> <analog_spans> <!-- The span name must match the name in your freetdm.conf --> <span name="myDahdiFXO"> <param name="dialplan" value="XML"/> <param name="context" value="default"/> <param name="answer-polarity-reverse" value="true"/> <param name="tonegroup" value="us"/> <param name="enable_callerid" value="true"/> <param name="enable-analog-option" value="call-swap"/> </span> </analog_spans> </configuration> ## Dialplan ## /usr/local/freeswitch/conf/dialplan/default/10_Outbound_FXO.xml <include> <extension name="Outbound_via_FreeTDM"> <condition field="${toll_allow}" expression="domestic"/> <condition field="destination_number" expression="^9(\d{8})$"> <action application="set" data="call_direction=outbound" /> <action application="set" data="hangup_after_bridge=true" /> <action application="set" data="effective_caller_id_number=${outbound_caller_id_number}"/> <action application="set" data="effective_caller_id_name=${outbound_caller_id_name}"/> <action application="bridge" data="freetdm/myDahdiFXO/a/${destination_number}"/> </condition> </extension> </include> Hope I have given enough info. Thanks in advance Errol