[Freeswitch-users] 30 Second call drop.

[Paul]

Hi Kaleem,

I will double check those settings.

I have my firewall setup very specific (it's not wide open to the world)..
I h accept port 5060 UDP and all the RTP ports but only if the source IP
is of my SIP Trunk provider proxy, otherwise it's invisible.

Thanks for the tip!

Paul

On Thu, July 18, 2013 1:06 pm, Kaleem wrote:
> For some wired reason my last mail is not showing any text,
>
>
> It was "Hi Paul,
>
>
> Had similar issues myself few months back, it ended up port blocked on
> external firewall.
>
> To confirm if its same issue, please test inbound and outbound call,
> outbound was disconnecting after 30 sec when free switch was sending 200
> ok and not receiving response."
>
> Don't know my emails are going blank :(
>
>
> Sent from my iPhone
>
>
> On 18 Jul 2013, at 20:55, Kaleem <k4kaleem at gmail.com> wrote:
>
>
>> Hi Paul,
>>
>>
>> Had similar issues myself few months back, it ended up port blocked on
>> external firewall.
>>
>> To confirm if its same issue, please test inbound and outbound call,
>> outbound was disconnecting after 30 sec when free switch was sending
>> 200 ok and not receiving response.
>>
>>
>> Sent from my iPhone
>>
>>
>> On 18 Jul 2013, at 16:54, "Paul" <pasha at prosperity4ever.com> wrote:
>>
>>
>>> Hi guys,
>>>
>>>
>>> After hours of googling and trying every different config options I
>>> need some help!
>>>
>>> My scenario is as follows:
>>>
>>>
>>> Remote Network 1: 192.168.1.0/24 (10.8.0.X/32 via openVPN tun)
>>> Remote Network 2: 192.168.5.0/24 (10.9.0.X/32 via openVPN tun)
>>>
>>>
>>> Main Network (where Freeswitch resides): 10.0.0.0/24
>>>
>>>
>>> My sip gateway/proxy: 10.0.0.40 (kamailio)
>>> Freeswitch: 10.0.0.34
>>>
>>>
>>> I can fully use the VPN from both networks (ssh, web gui control,
>>> etc)
>>>
>>> phones can register, however here are my problems:
>>>
>>> When calling incoming DID none of the extensions ever get ring, it
>>> skips to voicemail... when leaving a message voicemail cuts of after
>>> 30-31
>>> seconds exactly. I am wondering if freeswitch isn't detecting my
>>> client sending audio and interprets it as silence and therefore hangs
>>> up. The voicemail message itsel does contain everything said right up
>>> to the hang up.
>>>
>>> Sometimes I can call between extensions if they are on the same side
>>> of the VPN subnet (say 101 calling 101 and they both are coming from
>>> 192.168.1.0/24 via 10.8.0.0/24)
>>> If 100 is on 10.8.0/24 and 101 is on 10.9.0.0/24 freeswitch just says
>>> user is unavailable.
>>>
>>> I'm suspecting this is a NAT issue, all the reading I have done talks
>>>  about "external sip and rtp ip" in my case my trunk hooks up from
>>> private ip to private ip, it's the kamailio that's supposed to do the
>>> NAT (which I
>>> have verified works fine, I can place outgoing calls through it from
>>> other PBXs no problem with two way audio and working as it should be).
>>>
>>>
>>> I'm not sure if there is a way to enable nat or not with freeswitch.
>>> One
>>> thing I have done (as I've found this worked for some people) is set
>>> all references to sip-ip ext-sip-ip, rtp-ip and ext-rtp-ip to
>>> 10.0.0.34 (my
>>> freeswitch eth0). There are no other adapters on the box.
>>>
>>> I am hoping that as this is my first time setting up freeswitch that
>>> one of you freeswitch experts can point me in the right direction :)
>>>
>>> Thanks in advance guys!
>>>
>>>
>>>
>>>
>>>
>
> _________________________________________________________________________
>  Professional FreeSWITCH Consulting Services:
> consulting at freeswitch.org http://www.freeswitchsolutions.com
>
>
> 
> 
>
>
> Official FreeSWITCH Sites
> http://www.freeswitch.org
> http://wiki.freeswitch.org
> http://www.cluecon.com
>
>
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>
>