[Freeswitch-users] Need Help to setup freeswitch with sangoma card
Thangappan.M
thangappan143 at gmail.com
Sun Jan 24 21:50:02 PST 2010
The following link have the openzap.conf,openzap.conf.xml
,smg_pri.conf, output of oz list
and oz dump.
http://www.pastebin.org/81929
On Mon, Jan 25, 2010 at 9:55 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
> Here I mentioned the link which has the details of
> /etc/wanpipe/smg_pri.conf
> http://www.pastebin.org/81895
>
>
> On Sat, Jan 23, 2010 at 10:02 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
>
>> Updated the latest version of freeswitch ( 1.0.5-20100121-0400) and run
>> the wanrouter then freeswitch. While executing the freeswtich it said the
>> following error.
>>
>> [ERR] zap_io.c:2562 Error loading/usr/local/freeswitch/mod/ozmod_sangoma_boost.so
>>
>> [/usr/local/freeswitch/mod/ozmod_sangoma_boost.so: cannot open shared object
>> file: No such file or directory]
>> [ERR] zap_io.c:2722 can't find 'sangoma_boost
>>
>>
>>
>>
>> Searched about this in freeswitch mailing list and found one post was
>> there regarding the same problem. Finally found the problem. I missed to
>> install the SCTP packages. Installed it and compiled the freeswitch again
>> now the inbound call was landed on freeswitch.
>>
>> But I am unable to make a outbound call. When I was trying the following
>> was get.
>>
>> freeswitch at internal> originate openzap/smg_prid/a/9940464753 at g1openzap/smg_prid/a/9940464753 at g1
>> -ERR NORMAL_CIRCUIT_CONGESTION
>>
>> 2010-01-23 10:00:45.688854 [WARNING] ozmod_sangoma_boost.c:348 TX EVENT:
>> CALL_START:(80) [w1g1] CSid=2 Seq=2 Cn=[FreeSWITCH] Cd=[9940464753]
>> Ci=[0000000000] Rdnis=[]
>> freeswitch at internal> 2010-01-23 10:00:46.709355 [WARNING]
>> ozmod_sangoma_boost.c:1373 RX EVENT (N): CALL_START_NACK:(82) [w256g256]
>> Rc=0 CSid=2 Seq=2
>> 2010-01-23 10:00:46.709355 [WARNING] sangoma_boost_client.c:220 TX EVENT
>> (N): CALL_START_NACK_ACK:(83) [w1g1] Rc=0 CSid=2 Seq=3
>> 2010-01-23 10:00:46.709355 [ERR] mod_openzap.c:1162 No channels available
>> 2010-01-23 10:00:46.709355 [ERR] switch_ivr_originate.c:2411 Cannot create
>> outgoing channel of type [openzap] cause: [NORMAL_CIRCUIT_CONGESTION]
>> 2010-01-23 10:00:46.709355 [DEBUG] switch_ivr_originate.c:3211 Originate
>> Resulted in Error Cause: 34 [NORMAL_CIRCUIT_CONGESTION]
>>
>> Please help me...........
>>
>>
>>
>> On Fri, Jan 22, 2010 at 10:15 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
>>
>>> The following link have the openzap.conf,openzap.conf.xml ,smg_prid.conf
>>> , debug log of mod_openzap , oz list and oz dump 1 output.
>>>
>>> http://pastebin.org/80095
>>>
>>>
>>>
>>> On Thu, Jan 21, 2010 at 10:34 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
>>>
>>>> OpenZap is loading the ss7 signalling type. As per your concern openzap
>>>> does not know the details of the signalling then how it is loading the
>>>> ss7_boost libraries?
>>>>
>>>> FreeSWITCH log:
>>>> -----------------------------
>>>> 2010-01-21 10:10:46.707844 [INFO] zap_io.c:2374 Configured 30 channel(s)
>>>> 2010-01-21 10:10:46.708600 [INFO] zap_io.c:2468 Loading SIG from
>>>> /usr/local/freeswitch/mod/ozmod_ss7_boost.so
>>>> 2010-01-21 10:10:46.709031 [INFO] zap_io.c:2584 auto-loaded 'ss7_boost'
>>>> 2010-01-21 10:10:46.709466 [DEBUG] ss7_boost_client.c:124 Creating L=
>>>> 127.0.0.65:53000 R=127.0.0.66:53000
>>>> 2010-01-21 10:10:46.709834 [DEBUG] ss7_boost_client.c:124 Creating L=
>>>> 127.0.0.65:53001 R=127.0.0.66:53001
>>>> 2010-01-21 10:10:46.710424 [WARNING] ss7_boost_client.c:244 TX EVENT
>>>> (P): SYSTEM_RESTART:(87) [w1g1] Rc=0 CSid=0 Seq=0
>>>>
>>>> The signalling type might be anything but when I used the oz list
>>>> command it showed the span details. But I am unable to make a inbound and
>>>> outbound call.
>>>>
>>>> Outbound call result:
>>>> ============
>>>> > originate openzap/smg_prid/a/9940464753 openzap/smg_prid/a/9843171457
>>>> -ERR NORMAL_CIRCUIT_CONGESTION
>>>>
>>>> 2010-01-21 10:26:14.304816 [CRIT] ozmod_ss7_boost.c:244 SPAN is not
>>>> online.
>>>> freeswitch at internal> 2010-01-21 10:26:14.304816 [ERR]
>>>> mod_openzap.c:1043 No channels available
>>>> 2010-01-21 10:26:14.304816 [ERR] switch_ivr_originate.c:1510 Cannot
>>>> create outgoing channel of type [openzap] cause: [NORMAL_CIRCUIT_CONGESTION]
>>>> 2010-01-21 10:26:14.304816 [DEBUG] switch_ivr_originate.c:2138 Originate
>>>> Resulted in Error Cause: 34 [NORMAL_CIRCUIT_CONGESTION]
>>>>
>>>> Inbound call result:
>>>> -----------------------------
>>>>
>>>> I made incoming call for the dial plan which is specified in the
>>>> earlier post at that time it said the number is busy. We did the packet
>>>> capture using the following command.
>>>>
>>>> wanpipemon -i w1g1 -pcap -pcap file isdn.pcap -port ISDN -full -systime
>>>> -c trd
>>>>
>>>> Here I attached the pcap file for that.
>>>>
>>>>
>>>> Where I did mistake or Did I miss any thing to do?
>>>> Please help me.......
>>>>
>>>>
>>>>
>>>> On Wed, Jan 20, 2010 at 7:40 PM, Thangappan.M <thangappan143 at gmail.com>wrote:
>>>>
>>>>>
>>>>> I noticed the 'oz list' output in that span type is 'ss7
>>>>> (boost)'. How can I change this to isdn?
>>>>>
>>>>>
>>>>>
>>>>> On Wed, Jan 20, 2010 at 12:43 PM, Thangappan.M <
>>>>> thangappan143 at gmail.com> wrote:
>>>>>
>>>>>> I found the error in it. The file name is used as openzap.conf.xml (
>>>>>> smg_prid is specified here) and another file name as openzap.conf.wiki.xml (
>>>>>> PRI_1 span is specified here ). FreeSWITCH referred the PRI_1 span from
>>>>>> openzap.conf.wiki.xml file.
>>>>>>
>>>>>> Now the another problem is raised here.
>>>>>> When I was using oz list command , the details of the smg_prid shown.
>>>>>> When I was using 'oz dump smg_prid' command it shows all the channels'
>>>>>> details. But all the channels' states are DOWN. why? How can I make it the
>>>>>> states to UP?
>>>>>>
>>>>>> When I was making the call , the number is busy message was get. The
>>>>>> call was not at all landed to the freeswitch.
>>>>>>
>>>>>> Dial plan Example:
>>>>>> -------------------------------
>>>>>> <extension name="PRI_Testing">
>>>>>> <condition field="destination_number" expression="^39114600$">
>>>>>> <action application="playback"
>>>>>> data="ivr-welcome_to_freeswitch"/>
>>>>>> </condition>
>>>>>> </extension>
>>>>>>
>>>>>> Please help me...........
>>>>>>
>>>>>> *Output Reference:*
>>>>>> http://pastebin.org/79074
>>>>>>
>>>>>>
>>>>>> On Wed, Jan 20, 2010 at 11:25 AM, Thangappan.M <
>>>>>> thangappan143 at gmail.com> wrote:
>>>>>>
>>>>>>> Dear all,
>>>>>>>
>>>>>>> I have successfully configured wanpipe with freeswitch. When
>>>>>>> I was the running wancfg_fs script the following files openzap.conf ,
>>>>>>> autoload_confg/openzap.conf.xml , /etc/wanpipe/wanpipe1.xml, smg_pri.conf
>>>>>>> are created.
>>>>>>>
>>>>>>> I started the wanrouter command then executed the
>>>>>>> freeswitch.
>>>>>>> When I was executing freeswitch mod_openzap.c said the error
>>>>>>> as "Error for finding the span id. name:PRI_1".
>>>>>>> But in the openzap.conf and openzap.conf.xml files the span
>>>>>>> name is smg_prid.
>>>>>>>
>>>>>>> Why the freeswitch is referring the span name as PRI_1 ?
>>>>>>> Whether this has to configured in anywhere?
>>>>>>>
>>>>>>> In the freeswitch CLI using oz command I tried to dump the
>>>>>>> PRI_1 span id but it said te error as "PRI_1 is not found". When I was
>>>>>>> trying the command 'oz dump smg_prid' all the channel states and details
>>>>>>> shown.
>>>>>>>
>>>>>>> It seems that smg_prid span configured in openzap perfectly
>>>>>>> (Its my assumption). Then Why freeswitch is referring the span name as
>>>>>>> PRI_1.
>>>>>>>
>>>>>>> DID I MAKE ANY MISTAKE OR DID I MISS ANYTHING TO DO?
>>>>>>>
>>>>>>> Could anyone please help me?
>>>>>>>
>>>>>>> REFERENCE:
>>>>>>>
>>>>>>> openzap.conf
>>>>>>> [span wanpipe smg_prid]
>>>>>>> name => smg_prid
>>>>>>> trunk_type =>e1
>>>>>>> b-channel => 1:1-15
>>>>>>> b-channel => 1:17-31
>>>>>>>
>>>>>>>
>>>>>>> openzap.conf.xml
>>>>>>> <configuration name="openzap.conf" description="OpenZAP
>>>>>>> Configuration">
>>>>>>> <settings>
>>>>>>> <param name="debug" value="0"/>
>>>>>>> <!--<param name="hold-music" value="$${moh_uri}"/>-->
>>>>>>> <!--<param name="enable-analog-option" value="call-swap"/>-->
>>>>>>> <!--<param name="enable-analog-option" value="3-way"/>-->
>>>>>>> </settings>
>>>>>>> <boost_spans>
>>>>>>> <span id="smg_prid">
>>>>>>> <!--<param name="hold-music" value="$${moh_uri}"/>-->
>>>>>>> <param name="dialplan" value="XML"/>
>>>>>>> <param name="context" value="default"/>
>>>>>>> <!-- regex to stop dialing when it matches -->
>>>>>>> <!--<param name="dial-regex" value="5555"/>-->
>>>>>>> <!-- regex to stop dialing when it does not match -->
>>>>>>> <!--<param name="fail-dial-regex" value="^5"/>-->
>>>>>>> </span>
>>>>>>> </boost_spans>
>>>>>>> <analog_spans>
>>>>>>> </analog_spans>
>>>>>>> </configuration>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>>> --
>>>>>>> Regards,
>>>>>>> Thangappan.M
>>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Regards,
>>>>>> Thangappan.M
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> Regards,
>>>>> Thangappan.M
>>>>>
>>>>
>>>>
>>>>
>>>> --
>>>> Regards,
>>>> Thangappan.M
>>>>
>>>
>>>
>>>
>>> --
>>> Regards,
>>> Thangappan.M
>>>
>>
>>
>>
>> --
>> Regards,
>> Thangappan.M
>>
>
>
>
> --
> Regards,
> Thangappan.M
>
--
Regards,
Thangappan.M
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20100125/1d8d26d1/attachment-0002.html
More information about the FreeSWITCH-users
mailing list