[Freeswitch-users] Need Help to setup freeswitch with sangoma card
Thangappan.M
thangappan143 at gmail.com
Sun Jan 24 20:25:59 PST 2010
Here I mentioned the link which has the details of /etc/wanpipe/smg_pri.conf
http://www.pastebin.org/81895
On Sat, Jan 23, 2010 at 10:02 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
> Updated the latest version of freeswitch ( 1.0.5-20100121-0400) and run the
> wanrouter then freeswitch. While executing the freeswtich it said the
> following error.
>
> [ERR] zap_io.c:2562 Error loading/usr/local/freeswitch/mod/ozmod_sangoma_boost.so
>
> [/usr/local/freeswitch/mod/ozmod_sangoma_boost.so: cannot open shared object
> file: No such file or directory]
> [ERR] zap_io.c:2722 can't find 'sangoma_boost
>
>
>
>
> Searched about this in freeswitch mailing list and found one post was there
> regarding the same problem. Finally found the problem. I missed to install
> the SCTP packages. Installed it and compiled the freeswitch again now the
> inbound call was landed on freeswitch.
>
> But I am unable to make a outbound call. When I was trying the following
> was get.
>
> freeswitch at internal> originate openzap/smg_prid/a/9940464753 at g1openzap/smg_prid/a/9940464753 at g1
> -ERR NORMAL_CIRCUIT_CONGESTION
>
> 2010-01-23 10:00:45.688854 [WARNING] ozmod_sangoma_boost.c:348 TX EVENT:
> CALL_START:(80) [w1g1] CSid=2 Seq=2 Cn=[FreeSWITCH] Cd=[9940464753]
> Ci=[0000000000] Rdnis=[]
> freeswitch at internal> 2010-01-23 10:00:46.709355 [WARNING]
> ozmod_sangoma_boost.c:1373 RX EVENT (N): CALL_START_NACK:(82) [w256g256]
> Rc=0 CSid=2 Seq=2
> 2010-01-23 10:00:46.709355 [WARNING] sangoma_boost_client.c:220 TX EVENT
> (N): CALL_START_NACK_ACK:(83) [w1g1] Rc=0 CSid=2 Seq=3
> 2010-01-23 10:00:46.709355 [ERR] mod_openzap.c:1162 No channels available
> 2010-01-23 10:00:46.709355 [ERR] switch_ivr_originate.c:2411 Cannot create
> outgoing channel of type [openzap] cause: [NORMAL_CIRCUIT_CONGESTION]
> 2010-01-23 10:00:46.709355 [DEBUG] switch_ivr_originate.c:3211 Originate
> Resulted in Error Cause: 34 [NORMAL_CIRCUIT_CONGESTION]
>
> Please help me...........
>
>
>
> On Fri, Jan 22, 2010 at 10:15 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
>
>> The following link have the openzap.conf,openzap.conf.xml ,smg_prid.conf ,
>> debug log of mod_openzap , oz list and oz dump 1 output.
>>
>> http://pastebin.org/80095
>>
>>
>>
>> On Thu, Jan 21, 2010 at 10:34 AM, Thangappan.M <thangappan143 at gmail.com>wrote:
>>
>>> OpenZap is loading the ss7 signalling type. As per your concern openzap
>>> does not know the details of the signalling then how it is loading the
>>> ss7_boost libraries?
>>>
>>> FreeSWITCH log:
>>> -----------------------------
>>> 2010-01-21 10:10:46.707844 [INFO] zap_io.c:2374 Configured 30 channel(s)
>>> 2010-01-21 10:10:46.708600 [INFO] zap_io.c:2468 Loading SIG from
>>> /usr/local/freeswitch/mod/ozmod_ss7_boost.so
>>> 2010-01-21 10:10:46.709031 [INFO] zap_io.c:2584 auto-loaded 'ss7_boost'
>>> 2010-01-21 10:10:46.709466 [DEBUG] ss7_boost_client.c:124 Creating L=
>>> 127.0.0.65:53000 R=127.0.0.66:53000
>>> 2010-01-21 10:10:46.709834 [DEBUG] ss7_boost_client.c:124 Creating L=
>>> 127.0.0.65:53001 R=127.0.0.66:53001
>>> 2010-01-21 10:10:46.710424 [WARNING] ss7_boost_client.c:244 TX EVENT (P):
>>> SYSTEM_RESTART:(87) [w1g1] Rc=0 CSid=0 Seq=0
>>>
>>> The signalling type might be anything but when I used the oz list command
>>> it showed the span details. But I am unable to make a inbound and outbound
>>> call.
>>>
>>> Outbound call result:
>>> ============
>>> > originate openzap/smg_prid/a/9940464753 openzap/smg_prid/a/9843171457
>>> -ERR NORMAL_CIRCUIT_CONGESTION
>>>
>>> 2010-01-21 10:26:14.304816 [CRIT] ozmod_ss7_boost.c:244 SPAN is not
>>> online.
>>> freeswitch at internal> 2010-01-21 10:26:14.304816 [ERR] mod_openzap.c:1043
>>> No channels available
>>> 2010-01-21 10:26:14.304816 [ERR] switch_ivr_originate.c:1510 Cannot
>>> create outgoing channel of type [openzap] cause: [NORMAL_CIRCUIT_CONGESTION]
>>> 2010-01-21 10:26:14.304816 [DEBUG] switch_ivr_originate.c:2138 Originate
>>> Resulted in Error Cause: 34 [NORMAL_CIRCUIT_CONGESTION]
>>>
>>> Inbound call result:
>>> -----------------------------
>>>
>>> I made incoming call for the dial plan which is specified in the
>>> earlier post at that time it said the number is busy. We did the packet
>>> capture using the following command.
>>>
>>> wanpipemon -i w1g1 -pcap -pcap file isdn.pcap -port ISDN -full -systime
>>> -c trd
>>>
>>> Here I attached the pcap file for that.
>>>
>>>
>>> Where I did mistake or Did I miss any thing to do?
>>> Please help me.......
>>>
>>>
>>>
>>> On Wed, Jan 20, 2010 at 7:40 PM, Thangappan.M <thangappan143 at gmail.com>wrote:
>>>
>>>>
>>>> I noticed the 'oz list' output in that span type is 'ss7
>>>> (boost)'. How can I change this to isdn?
>>>>
>>>>
>>>>
>>>> On Wed, Jan 20, 2010 at 12:43 PM, Thangappan.M <thangappan143 at gmail.com
>>>> > wrote:
>>>>
>>>>> I found the error in it. The file name is used as openzap.conf.xml (
>>>>> smg_prid is specified here) and another file name as openzap.conf.wiki.xml (
>>>>> PRI_1 span is specified here ). FreeSWITCH referred the PRI_1 span from
>>>>> openzap.conf.wiki.xml file.
>>>>>
>>>>> Now the another problem is raised here.
>>>>> When I was using oz list command , the details of the smg_prid shown.
>>>>> When I was using 'oz dump smg_prid' command it shows all the channels'
>>>>> details. But all the channels' states are DOWN. why? How can I make it the
>>>>> states to UP?
>>>>>
>>>>> When I was making the call , the number is busy message was get. The
>>>>> call was not at all landed to the freeswitch.
>>>>>
>>>>> Dial plan Example:
>>>>> -------------------------------
>>>>> <extension name="PRI_Testing">
>>>>> <condition field="destination_number" expression="^39114600$">
>>>>> <action application="playback"
>>>>> data="ivr-welcome_to_freeswitch"/>
>>>>> </condition>
>>>>> </extension>
>>>>>
>>>>> Please help me...........
>>>>>
>>>>> *Output Reference:*
>>>>> http://pastebin.org/79074
>>>>>
>>>>>
>>>>> On Wed, Jan 20, 2010 at 11:25 AM, Thangappan.M <
>>>>> thangappan143 at gmail.com> wrote:
>>>>>
>>>>>> Dear all,
>>>>>>
>>>>>> I have successfully configured wanpipe with freeswitch. When
>>>>>> I was the running wancfg_fs script the following files openzap.conf ,
>>>>>> autoload_confg/openzap.conf.xml , /etc/wanpipe/wanpipe1.xml, smg_pri.conf
>>>>>> are created.
>>>>>>
>>>>>> I started the wanrouter command then executed the freeswitch.
>>>>>> When I was executing freeswitch mod_openzap.c said the error
>>>>>> as "Error for finding the span id. name:PRI_1".
>>>>>> But in the openzap.conf and openzap.conf.xml files the span
>>>>>> name is smg_prid.
>>>>>>
>>>>>> Why the freeswitch is referring the span name as PRI_1 ?
>>>>>> Whether this has to configured in anywhere?
>>>>>>
>>>>>> In the freeswitch CLI using oz command I tried to dump the
>>>>>> PRI_1 span id but it said te error as "PRI_1 is not found". When I was
>>>>>> trying the command 'oz dump smg_prid' all the channel states and details
>>>>>> shown.
>>>>>>
>>>>>> It seems that smg_prid span configured in openzap perfectly
>>>>>> (Its my assumption). Then Why freeswitch is referring the span name as
>>>>>> PRI_1.
>>>>>>
>>>>>> DID I MAKE ANY MISTAKE OR DID I MISS ANYTHING TO DO?
>>>>>>
>>>>>> Could anyone please help me?
>>>>>>
>>>>>> REFERENCE:
>>>>>>
>>>>>> openzap.conf
>>>>>> [span wanpipe smg_prid]
>>>>>> name => smg_prid
>>>>>> trunk_type =>e1
>>>>>> b-channel => 1:1-15
>>>>>> b-channel => 1:17-31
>>>>>>
>>>>>>
>>>>>> openzap.conf.xml
>>>>>> <configuration name="openzap.conf" description="OpenZAP
>>>>>> Configuration">
>>>>>> <settings>
>>>>>> <param name="debug" value="0"/>
>>>>>> <!--<param name="hold-music" value="$${moh_uri}"/>-->
>>>>>> <!--<param name="enable-analog-option" value="call-swap"/>-->
>>>>>> <!--<param name="enable-analog-option" value="3-way"/>-->
>>>>>> </settings>
>>>>>> <boost_spans>
>>>>>> <span id="smg_prid">
>>>>>> <!--<param name="hold-music" value="$${moh_uri}"/>-->
>>>>>> <param name="dialplan" value="XML"/>
>>>>>> <param name="context" value="default"/>
>>>>>> <!-- regex to stop dialing when it matches -->
>>>>>> <!--<param name="dial-regex" value="5555"/>-->
>>>>>> <!-- regex to stop dialing when it does not match -->
>>>>>> <!--<param name="fail-dial-regex" value="^5"/>-->
>>>>>> </span>
>>>>>> </boost_spans>
>>>>>> <analog_spans>
>>>>>> </analog_spans>
>>>>>> </configuration>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>> --
>>>>>> Regards,
>>>>>> Thangappan.M
>>>>>>
>>>>>
>>>>>
>>>>>
>>>>> --
>>>>> Regards,
>>>>> Thangappan.M
>>>>>
>>>>
>>>>
>>>>
>>>> --
>>>> Regards,
>>>> Thangappan.M
>>>>
>>>
>>>
>>>
>>> --
>>> Regards,
>>> Thangappan.M
>>>
>>
>>
>>
>> --
>> Regards,
>> Thangappan.M
>>
>
>
>
> --
> Regards,
> Thangappan.M
>
--
Regards,
Thangappan.M
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20100125/64148ba9/attachment-0002.html
More information about the FreeSWITCH-users
mailing list