[Freeswitch-users] Openzap
Michael Collins
mcollins at fcnetwork.com
Thu Nov 8 23:03:12 PST 2007
John,
Any luck with this one?
-MC
> -----Original Message-----
> From: freeswitch-users-bounces at lists.freeswitch.org
[mailto:freeswitch-
> users-bounces at lists.freeswitch.org] On Behalf Of John Bittner
> Sent: Thursday, November 08, 2007 1:28 AM
> To: Brian West
> Cc: freeswitch-users at lists.freeswitch.org
> Subject: Re: [Freeswitch-users] Openzap
>
> Hi Brian,
> I have no clue if this is even close.
>
> John B
>
> openzap.conf
> [span wanpipe]
> name => OpenZAP
> number => 1
> trunk_type => t1
> b-channel => 1:1-23
> d-channel => 1:24
>
> wanpipe.conf
> [defaults]
> codec_ms => 20
> wink_ms => 150
> flash_ms => 750
>
> openzap.conf.xml
> <configuration name="openzap.conf" description="OpenZAP
Configuration">
> <settings>
> <param name="debug" value="0"/>
> </settings>
> <pri_spans>
> <span id="1">
> <param name="mode" value="user"/>
> <param name="dialect" value="DMS"/>
> <param name="dialplan" value="XML"/>
> <param name="context" value="default"/>
> </span>
> </pri_spans>
> </configuration>
>
> wanpipe.conf.xml
> configuration name="wanpipe.conf" description="Sangoma Wanpipe
Endpoint">
> <settings>
> <param name="debug" value="0"/>
> <param name="dialplan" value="XML"/>
> <param name="ms-per-frame" value="20"/>
> <param name="dtmf-on" value="800"/>
> <param name="dtmf-off" value="100"/>
> <param name="supress-dtmf-tone" value="yes"/>
> </settings>
> <ss7boost_handles>
> <!--
> <handle>
> <param name="local-ip" value="127.0.0.65"/>
> <param name="local-port" value="53000"/>
> <param name="remote-ip" value="127.0.0.66"/>
> <param name="remote-port" value="53000"/>
> </handle>
> -->
> </ss7boost_handles>
> <pri_spans>
> <!-- may be any single digit or a range of digits separated by a
'-'
> e.g "1-4" -->
> <span id="1">
> <param name="node" value="cpe"/>
> <param name="switch" value="dms100"/>
> <!--<param name="switch" value="dms100"/>-->
> <!-- <param name="switch" value="lucent5e"/> -->
> <!-- <param name="switch" value="att4ess"/> -->
> <!-- <param name="switch" value="euroisdn"/> -->
> <!-- <param name="switch" value="gr303eoc"/> -->
> <!-- <param name="switch" value="gr303tmc"/> -->
> <param name="dp" value="national"/>
> <!-- <param name="dp" value="international"/> -->
> <!-- <param name="dp" value="local"/> -->
> <!-- <param name="dp" value="private"/> -->
> <!-- <param name="dp" value="unknown"/> -->
> <param name="l1" value="ulaw"/>
> <!-- <param name="l1" value="alaw"/> -->
> <param name="bchan" value="1-23"/>
> <param name="dchan" value="24"/>
> <param name="dialplan" value="XML"/>
> </span>
> </pri_spans>
> </configuration
>
> -----Original Message-----
> Show me your wanpipe config for this span please. DMS100 should work
> without a problem.
>
> /b
>
> On Nov 8, 2007, at 8:00 AM, John Bittner wrote:
>
> >
> > Hi Brian,
> > I can use DMS100. Is there anything I am missing on the wanpipe
side.
> > If I move back to the mod_wanpipe with LIBPRI can I use NI2? I need
to
> > use the data part of wanrouter, I think I remember reading that if
you
> > use mod_wanpipe you have to be TDM only. Is this true?
> >
> > What is the best way to get this sanagoma working and still keep the
> > data stuff working.
> >
> > John Bittner
> > Simlab.net
> >
> > -----Original Message-----
> > OpenZap doesn't do NI2 just yet. Its on the to do list for the PRI
> > stack.
> >
> > /b
> >
> > On Nov 8, 2007, at 3:39 AM, John Bittner wrote:
> >
> >> Thanks Michael but I had already tried this config. It does even
like
> >> the formats. I tried testing a few configs and the only one I get a
> >> response with is
> >>
> >> [span wanpipe]
> >> b-channel => 1:1-23
> >> d-channel => 1:24
> >>
> >> This gives me this error. The device listed in wanpipe is w1g1 and
> >> does not match s1c1... so I am missing something.
> >> I tried to even to go into the code to find the options but I cant
> >> find anything. I suck at programming. Anyone have any idea of the
> >> options for this or a sample config for a sangoma card.
> >>
> >> Any help is appreciated.
> >>
> >> Thanks
> >>
> >> John Bittner
> >> Simlab.net
> >>
> >>
> >> 2007-11-07 17:28:10 [ERR] zap_io.c:1868 process_module_config()
> >> Cannot open zt.conf
> >> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1744 load_config() found
config
> >> for span
> >> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1764 load_config() created
span
> >> 9 of type wanpipe
> >> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1777 load_config() span 9
> >> [spanno]=[2]
> >> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1777 load_config() span 9 [b-
> >> channel]=[1:1-23]
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c1
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c2
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c3
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c4
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c5
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c6
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c7
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c8
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c9
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c10
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c11
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c12
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c13
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c14
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c15
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c16
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c17
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c18
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c19
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c20
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c21
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c22
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c23
> >> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1777 load_config() span 9 [d-
> >> channel]=[1:24]
> >> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
> >> configuring device s1c24
> >> 2007-11-07 17:28:10 [INFO] zap_io.c:1848 load_config() Configured 0
> >> channel(s)
> >> 2007-11-07 17:28:10 [ERR] zap_io.c:1926 zap_global_init() No
modules
> >> configured!
> >> 2007-11-07 17:28:10 [ERR] mod_openzap.c:1201 mod_openzap_load()
> >> Error loading OpenZAP
> >>
> >> -----Original Message-----
> >> John,
> >>
> >> I don't have a Sangoma card, but if I understand the openzap stuff
> >> correctly it will replace wanpipe. I do have a tor2 clone. Here's
> >> my
> >> openzap.conf with comments below:
> >>
> >> [span zt]
> >> name => OpenZAP
> >> number => 1
> >> trunk_type => t1
> >> b-channel => 1-24
> >>
> >> [span zt]
> >> name => OpenZAP
> >> number => 2
> >> trunk_type => t1
> >> b-channel => 25-48
> >>
> >> [span zt]
> >> name => OpenZAP
> >> number => 3
> >> trunk_type => t1
> >> b-channel => 49-71
> >> d-channel => 72
> >>
> >> [span zt]
> >> name => OpenZAP
> >> number => 4
> >> trunk_type => t1
> >> b-channel => 73-95
> >> d-channel => 96
> >>
> >>
> >> Note in particular spans 3 and 4. Span 3 is a working PRI where
I'm
> >> connected to an Asterisk server that is pretending to be the telco.
> >>
> >> Here's the corresponding openzap.conf.xml:
> >>
> >> <configuration name="openzap.conf" description="OpenZAP
> >> Configuration">
> >> <settings>
> >> <param name="debug" value="1"/>
> >> </settings>
> >>
> >> <analog_spans>
> >> <span id="1">
> >> <param name="dialplan" value="XML"/>
> >> <param name="context" value="default"/>
> >> </span>
> >> <span id="2">
> >> <param name="dialplan" value="XML"/>
> >> <param name="context" value="default"/>
> >> </span>
> >> </analog_spans>
> >>
> >> <pri_spans>
> >> <span id="3">
> >> <param name="mode" value="user"/>
> >> <param name="dialect" value="DMS"/>
> >> <param name="dialplan" value="XML"/>
> >> <param name="context" value="default"/>
> >> </span>
> >> <span id="4">
> >> <param name="mode" value="user"/>
> >> <param name="dialect" value="DMS"/>
> >> <param name="dialplan" value="XML"/>
> >> <param name="context" value="default"/>
> >> </span>
> >> </pri_spans>
> >> </configuration>
> >>
> >>
> >> Again note span 3, which is a working PRI.
> >>
> >> The trouble is, I don't believe that Mike has gotten to NI-2 just
> >> yet.
> >> I know DMS100 works if that is an option. I haven't tested
4ess/5ess
> >> yet either. Sorry!
> >>
> >> At the very least you could use a setup like mine and get
connected.
> >> Your D-channel will probably complain, but if they complain then at
> >> least you know your cards are installed and working.
> >>
> >> Again, let us know how it goes...
> >>
> >> -MC
> >>
> >>> -----Original Message-----
> >>> From: freeswitch-users-bounces at lists.freeswitch.org
> >> [mailto:freeswitch-
> >>> users-bounces at lists.freeswitch.org] On Behalf Of John Bittner
> >>> Sent: Wednesday, November 07, 2007 6:51 PM
> >>> To: Michael Collins
> >>> Subject: Re: [Freeswitch-users] Openzap
> >>>
> >>>
> >>> Thanks Michael,
> >>> That worked but now I have errors trying to get openzap to see the
> >>> card. Do know were to get a openzap.conf sample config for a A104D
> >>> card with 1 T1 Pri running NI2. I cant find any samples for
> >>> wanpipe...
> >>> only zap.
> >>>
> >>> John B
> >>>
> >>> -----Original Message-----
> >>> John,
> >>>
> >>> Do you have /etc/openzap/zt.conf?
> >>>
> >>> I think you need all these in /etc/openzap:
> >>> zt.conf
> >>> openzap.conf
> >>> wanpipe.conf
> >>>
> >>>
> >>> Check that and let us now...
> >>> -MC
> >>>
> >>>> -----Original Message-----
> >>>> From: freeswitch-users-bounces at lists.freeswitch.org
> >>> [mailto:freeswitch-
> >>>> users-bounces at lists.freeswitch.org] On Behalf Of John Bittner
> >>>> Sent: Wednesday, November 07, 2007 5:30 PM
> >>>> To: freeswitch-users at lists.freeswitch.org
> >>>> Subject: [Freeswitch-users] Openzap
> >>>>
> >>>> Hey Guys,
> >>>> Am I missing something ?
> >>>> I got openzap to compile. I have a sangoma T1 card installed with
> >>>> wanpipe. I have the card configured, and I have wanpipe.conf file
> >>>> in
> >>>> the /usr/local/freeswitch/conf directory. Still I am getting this
> >>>> error when I try to load the module.
> >>>>
> >>>> 2007-11-07 15:25:21 [ERR] zap_io.c:1868 process_module_config()
> >> Cannot
> >>>> open wanpipe.conf
> >>>> 2007-11-07 15:25:21 [ERR] zap_io.c:1868 process_module_config()
> >> Cannot
> >>>> open zt.conf
> >>>> 2007-11-07 15:25:21 [ERR] zap_io.c:1926 zap_global_init() No
> >>>> modules
> >>>> configured!
> >>>> 2007-11-07 15:25:21 [ERR] mod_openzap.c:1201 mod_openzap_load()
> >> Error
> >>>> loading OpenZAP
> >>>>
> >>>> If there a special place I need to put the wanpipe.conf file?
> >>>>
> >>>> Any help is appreciated.
> >>>>
> >>>> Thanks
> >>>>
> >>>> John Bittner
> >>>> Simlab.net
> >>>>
> >>>>
> >>>>
> >>>> _______________________________________________
> >>>> Freeswitch-users mailing list
> >>>> Freeswitch-users at lists.freeswitch.org
> >>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >>>>
> >>>
> >> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-
> users
> >>>> http://www.freeswitch.org
> >>>
> >>> _______________________________________________
> >>> Freeswitch-users mailing list
> >>> Freeswitch-users at lists.freeswitch.org
> >>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >>>
> >> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-
> users
> >>> http://www.freeswitch.org
> >>>
> >>>
> >>> --
> >>>
> >>>
> >>>
> >>> _______________________________________________
> >>> Freeswitch-users mailing list
> >>> Freeswitch-users at lists.freeswitch.org
> >>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >>>
> >> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-
> users
> >>> http://www.freeswitch.org
> >>
> >> _______________________________________________
> >> Freeswitch-users mailing list
> >> Freeswitch-users at lists.freeswitch.org
> >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-
> users
> >> http://www.freeswitch.org
> >>
> >>
> >> --
> >>
> >>
> >>
> >> _______________________________________________
> >> Freeswitch-users mailing list
> >> Freeswitch-users at lists.freeswitch.org
> >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-
> users
> >> http://www.freeswitch.org
> >
> >
> > _______________________________________________
> > Freeswitch-users mailing list
> > Freeswitch-users at lists.freeswitch.org
> > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> > http://www.freeswitch.org
> >
> >
> > --
> >
> >
> >
> > _______________________________________________
> > Freeswitch-users mailing list
> > Freeswitch-users at lists.freeswitch.org
> > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> >
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> > http://www.freeswitch.org
>
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>
> --
> BEGIN-ANTISPAM-VOTING-LINKS
> ------------------------------------------------------
>
> Teach CanIt if this mail (ID 10788571) is spam:
> Spam:
https://mx1.simlab.net/b.php?i=10788571&m=c3ecd3fe8a97&c=s
> Not spam:
https://mx1.simlab.net/b.php?i=10788571&m=c3ecd3fe8a97&c=n
> Forget vote:
https://mx1.simlab.net/b.php?i=10788571&m=c3ecd3fe8a97&c=f
> ------------------------------------------------------
> END-ANTISPAM-VOTING-LINKS
>
>
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
More information about the FreeSWITCH-users
mailing list