[Freeswitch-users] Openzap

John Bittner john at simlab.net
Thu Nov 8 01:27:47 PST 2007 

Hi Brian,
I have no clue if this is even close.

John B

openzap.conf
[span wanpipe]
name => OpenZAP
number => 1
trunk_type => t1
b-channel => 1:1-23
d-channel => 1:24

wanpipe.conf
[defaults]
codec_ms => 20
wink_ms => 150
flash_ms => 750

openzap.conf.xml
<configuration name="openzap.conf" description="OpenZAP Configuration">
  <settings>
    <param name="debug" value="0"/>
  </settings>
  <pri_spans>
    <span id="1">
      <param name="mode" value="user"/>
      <param name="dialect" value="DMS"/>
      <param name="dialplan" value="XML"/>
      <param name="context" value="default"/>
    </span>
  </pri_spans>
</configuration>

wanpipe.conf.xml
configuration name="wanpipe.conf" description="Sangoma Wanpipe Endpoint">
  <settings>
    <param name="debug" value="0"/>
    <param name="dialplan" value="XML"/>
    <param name="ms-per-frame" value="20"/>
    <param name="dtmf-on" value="800"/>
    <param name="dtmf-off" value="100"/>
    <param name="supress-dtmf-tone" value="yes"/>
  </settings>
  <ss7boost_handles>
<!--
    <handle>
      <param name="local-ip" value="127.0.0.65"/>
      <param name="local-port" value="53000"/>
      <param name="remote-ip" value="127.0.0.66"/>
      <param name="remote-port" value="53000"/>
    </handle>
-->
  </ss7boost_handles>
  <pri_spans>
    <!-- may be any single digit or a range of digits separated by a '-' e.g "1-4" -->
    <span id="1">
      <param name="node" value="cpe"/>
      <param name="switch" value="dms100"/>
      <!--<param name="switch" value="dms100"/>-->
      <!-- <param name="switch" value="lucent5e"/> -->
      <!-- <param name="switch" value="att4ess"/> -->
      <!-- <param name="switch" value="euroisdn"/> -->
      <!-- <param name="switch" value="gr303eoc"/> -->
      <!-- <param name="switch" value="gr303tmc"/> -->
      <param name="dp" value="national"/>
      <!-- <param name="dp" value="international"/> -->
      <!-- <param name="dp" value="local"/> -->
      <!-- <param name="dp" value="private"/> -->
      <!-- <param name="dp" value="unknown"/> -->
      <param name="l1" value="ulaw"/>
      <!-- <param name="l1" value="alaw"/> -->
      <param name="bchan" value="1-23"/>
      <param name="dchan" value="24"/>
      <param name="dialplan" value="XML"/>
    </span>
  </pri_spans>
</configuration

-----Original Message-----
Show me your wanpipe config for this span please.  DMS100 should work  
without a problem.

/b

On Nov 8, 2007, at 8:00 AM, John Bittner wrote:

>
> Hi Brian,
> I can use DMS100. Is there anything I am missing on the wanpipe side.
> If I move back to the mod_wanpipe with LIBPRI can I use NI2? I need to
> use the data part of wanrouter, I think I remember reading that if you
> use mod_wanpipe you have to be TDM only. Is this true?
>
> What is the best way to get this sanagoma working and still keep the
> data stuff working.
>
> John Bittner
> Simlab.net
>
> -----Original Message-----
> OpenZap doesn't do NI2 just yet.  Its on the to do list for the PRI
> stack.
>
> /b
>
> On Nov 8, 2007, at 3:39 AM, John Bittner wrote:
>
>> Thanks Michael but I had already tried this config. It does even like
>> the formats. I tried testing a few configs and the only one I get a
>> response with is
>>
>> [span wanpipe]
>> b-channel => 1:1-23
>> d-channel => 1:24
>>
>> This gives me this error. The device listed in wanpipe is w1g1 and
>> does not match s1c1... so I am missing something.
>> I tried to even to go into the code to find the options but I cant
>> find anything. I suck at programming. Anyone have any idea of the
>> options for this or a sample config for a sangoma card.
>>
>> Any help is appreciated.
>>
>> Thanks
>>
>> John Bittner
>> Simlab.net
>>
>>
>> 2007-11-07 17:28:10 [ERR] zap_io.c:1868 process_module_config()
>> Cannot open zt.conf
>> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1744 load_config() found config
>> for span
>> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1764 load_config() created span
>> 9 of type wanpipe
>> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1777 load_config() span 9
>> [spanno]=[2]
>> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1777 load_config() span 9 [b-
>> channel]=[1:1-23]
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c1
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c2
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c3
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c4
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c5
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c6
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c7
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c8
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c9
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c10
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c11
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c12
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c13
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c14
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c15
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c16
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c17
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c18
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c19
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c20
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c21
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c22
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c23
>> 2007-11-07 17:28:10 [DEBUG] zap_io.c:1777 load_config() span 9 [d-
>> channel]=[1:24]
>> 2007-11-07 17:28:10 [ERR] zap_wanpipe.c:404 wp_open_range() failure
>> configuring device s1c24
>> 2007-11-07 17:28:10 [INFO] zap_io.c:1848 load_config() Configured 0
>> channel(s)
>> 2007-11-07 17:28:10 [ERR] zap_io.c:1926 zap_global_init() No modules
>> configured!
>> 2007-11-07 17:28:10 [ERR] mod_openzap.c:1201 mod_openzap_load()
>> Error loading OpenZAP
>>
>> -----Original Message-----
>> John,
>>
>> I don't have a Sangoma card, but if I understand the openzap stuff
>> correctly it will replace wanpipe.  I do have a tor2 clone.  Here's  
>> my
>> openzap.conf with comments below:
>>
>> [span zt]
>> name => OpenZAP
>> number => 1
>> trunk_type => t1
>> b-channel => 1-24
>>
>> [span zt]
>> name => OpenZAP
>> number => 2
>> trunk_type => t1
>> b-channel => 25-48
>>
>> [span zt]
>> name => OpenZAP
>> number => 3
>> trunk_type => t1
>> b-channel => 49-71
>> d-channel => 72
>>
>> [span zt]
>> name => OpenZAP
>> number => 4
>> trunk_type => t1
>> b-channel => 73-95
>> d-channel => 96
>>
>>
>> Note in particular spans 3 and 4.  Span 3 is a working PRI where I'm
>> connected to an Asterisk server that is pretending to be the telco.
>>
>> Here's the corresponding openzap.conf.xml:
>>
>> <configuration name="openzap.conf" description="OpenZAP
>> Configuration">
>>  <settings>
>>    <param name="debug" value="1"/>
>>  </settings>
>>
>>  <analog_spans>
>>    <span id="1">
>>      <param name="dialplan" value="XML"/>
>>      <param name="context" value="default"/>
>>    </span>
>>    <span id="2">
>>      <param name="dialplan" value="XML"/>
>>      <param name="context" value="default"/>
>>    </span>
>>  </analog_spans>
>>
>>  <pri_spans>
>>    <span id="3">
>>      <param name="mode" value="user"/>
>>      <param name="dialect" value="DMS"/>
>>      <param name="dialplan" value="XML"/>
>>      <param name="context" value="default"/>
>>    </span>
>>    <span id="4">
>>      <param name="mode" value="user"/>
>>      <param name="dialect" value="DMS"/>
>>      <param name="dialplan" value="XML"/>
>>      <param name="context" value="default"/>
>>    </span>
>>  </pri_spans>
>> </configuration>
>>
>>
>> Again note span 3, which is a working PRI.
>>
>> The trouble is, I don't believe that Mike has gotten to NI-2 just  
>> yet.
>> I know DMS100 works if that is an option.  I haven't tested 4ess/5ess
>> yet either.  Sorry!
>>
>> At the very least you could use a setup like mine and get connected.
>> Your D-channel will probably complain, but if they complain then at
>> least you know your cards are installed and working.
>>
>> Again, let us know how it goes...
>>
>> -MC
>>
>>> -----Original Message-----
>>> From: freeswitch-users-bounces at lists.freeswitch.org
>> [mailto:freeswitch-
>>> users-bounces at lists.freeswitch.org] On Behalf Of John Bittner
>>> Sent: Wednesday, November 07, 2007 6:51 PM
>>> To: Michael Collins
>>> Subject: Re: [Freeswitch-users] Openzap
>>>
>>>
>>> Thanks Michael,
>>> That worked but now I have errors trying to get openzap to see the
>>> card. Do know were to get a openzap.conf sample config for a A104D
>>> card with 1 T1 Pri running NI2. I cant find any samples for
>>> wanpipe...
>>> only zap.
>>>
>>> John B
>>>
>>> -----Original Message-----
>>> John,
>>>
>>> Do you have /etc/openzap/zt.conf?
>>>
>>> I think you need all these in /etc/openzap:
>>> zt.conf
>>> openzap.conf
>>> wanpipe.conf
>>>
>>>
>>> Check that and let us now...
>>> -MC
>>>
>>>> -----Original Message-----
>>>> From: freeswitch-users-bounces at lists.freeswitch.org
>>> [mailto:freeswitch-
>>>> users-bounces at lists.freeswitch.org] On Behalf Of John Bittner
>>>> Sent: Wednesday, November 07, 2007 5:30 PM
>>>> To: freeswitch-users at lists.freeswitch.org
>>>> Subject: [Freeswitch-users] Openzap
>>>>
>>>> Hey Guys,
>>>> Am I missing something ?
>>>> I got openzap to compile. I have a sangoma T1 card installed with
>>>> wanpipe. I have the card configured, and I have wanpipe.conf file  
>>>> in
>>>> the /usr/local/freeswitch/conf directory. Still I am getting this
>>>> error when I try to load the module.
>>>>
>>>> 2007-11-07 15:25:21 [ERR] zap_io.c:1868 process_module_config()
>> Cannot
>>>> open wanpipe.conf
>>>> 2007-11-07 15:25:21 [ERR] zap_io.c:1868 process_module_config()
>> Cannot
>>>> open zt.conf
>>>> 2007-11-07 15:25:21 [ERR] zap_io.c:1926 zap_global_init() No  
>>>> modules
>>>> configured!
>>>> 2007-11-07 15:25:21 [ERR] mod_openzap.c:1201 mod_openzap_load()
>> Error
>>>> loading OpenZAP
>>>>
>>>> If there a special place I need to put the wanpipe.conf file?
>>>>
>>>> Any help is appreciated.
>>>>
>>>> Thanks
>>>>
>>>> John Bittner
>>>> Simlab.net
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Freeswitch-users mailing list
>>>> Freeswitch-users at lists.freeswitch.org
>>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>>>
>>>
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>>> http://www.freeswitch.org
>>>
>>> _______________________________________________
>>> Freeswitch-users mailing list
>>> Freeswitch-users at lists.freeswitch.org
>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>>
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>> http://www.freeswitch.org
>>>
>>>
>>> --
>>>
>>>
>>>
>>> _______________________________________________
>>> Freeswitch-users mailing list
>>> Freeswitch-users at lists.freeswitch.org
>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>>
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>> http://www.freeswitch.org
>>
>> _______________________________________________
>> Freeswitch-users mailing list
>> Freeswitch-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>>
>> -- 
>>
>>
>>
>> _______________________________________________
>> Freeswitch-users mailing list
>> Freeswitch-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>
> -- 
>
>
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org


_______________________________________________
Freeswitch-users mailing list
Freeswitch-users at lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org


-- 
BEGIN-ANTISPAM-VOTING-LINKS
------------------------------------------------------

Teach CanIt if this mail (ID 10788571) is spam:
Spam:        https://mx1.simlab.net/b.php?i=10788571&m=c3ecd3fe8a97&c=s
Not spam:    https://mx1.simlab.net/b.php?i=10788571&m=c3ecd3fe8a97&c=n
Forget vote: https://mx1.simlab.net/b.php?i=10788571&m=c3ecd3fe8a97&c=f
------------------------------------------------------
END-ANTISPAM-VOTING-LINKS

More information about the FreeSWITCH-users mailing list