[Freeswitch-dev] [Freeswitch-users] About the display problem during calling

[sparklezou]

Hi Brian,

It's the default Dialplan.

I have tried the fresh last version also. The same result. It should NOT be configuration problem.

You could review the wireshark log.

Thanks!

2012-12-03



sparklezou



发件人：sparklezou
发送时间：2012-12-02 17:03
主题：Re: [Freeswitch-dev] [Freeswitch-users] About the display problem during calling
收件人："freeswitch-dev"<freeswitch-dev at lists.freeswitch.org>
抄送：

Hi Develop team,

In these days, I reviewed the "DEBUG" info, and the sip info log. summarize as following:

Caller  <---> FS, in the "from" with dispaly neam. The display is set from the Caller Phone. in the "to" without the display name. As the caller only dial the number.


FS -----> Called, in the "from" with display name.It's transfer from "Caller  <---> FS". in the "to" without the display neme. As the caller only dial the number.

Called  -----> FS. in the "to" with display name. Here the Called Phone add the Display name into the SIP message.

Here conside the "Caller <----> FS"  and "FS<---->Called" are two sessions. I think the best way, is check the Display Name of Called in FS system when get the INVITE message. Add the Display Name for the called in the whole process.

Then in the following whole process, there will be display name both for "from" & "to".

How about your idea?

Thanks in advance!

2012-12-02



sparklezou



发件人：sparklezou
发送时间：2012-11-30 21:13
主题：Re: Re: [Freeswitch-users] About the display problem during calling
收件人："freeswitch-dev"<freeswitch-dev at lists.freeswitch.org>
抄送：

Hi Develop team,

Just simlify this question.

In the message 100, 180,183, 200 response to the caller side from Freeswitch side, the called part Name should be include in the sip address of "To" & SDP part. It should be  "ABC"<sip: 1234 at a.b.c.d>, NOT only <sip: 1234 at a.b.c.d>.

Currently, at the called part, the caller info is correct with Name. So the display at called side is OK.

Could you please let me know where is the source code for such process? I also would like to review it.

Thanks!

2012-11-30



sparklezou



发件人：sparklezou
发送时间：2012-11-30 15:55
主题：Re: [Freeswitch-users] About the display problem during calling
收件人："freeswitch-dev"<freeswitch-dev at lists.freeswitch.org>
抄送："freeswitch-users"<freeswitch-users at lists.freeswitch.org>

Hi All,

Before, I saved the user name in the phone. So it will show the name when ringing.

From the FreeSwitch side, there is NO difference.

@ Develop Team,

For Internal call, or any sip call from gateway, it should be better show the Name during ring.  And also keep show the name in the call, in stead of "Outbound Call".

Usually the phone will update the display name from the sip response message.

So in the 100, 180, 183, 200 sip/sdp message. Respons with the called name, like "ABC"<sip: 1234 at a.b.c.d>.

Currently in the inital 100,180,183 message, only <sip: 1234 at a.b.c.d>. In the 200 message "Remote-Part-ID: "Outbound Call" <sip: 1234 at a.b.c.d>; ....... "

If it could be updated, then the called name could be displayed on the caller phone.

Thanks!

2012-11-30



sparklezou



发件人：sparklezou
发送时间：2012-11-30 11:19
主题：[Freeswitch-users] About the display problem during calling
收件人："freeswitch-users"<freeswitch-users at lists.freeswitch.org>,"freeswitch-dev"<freeswitch-dev at lists.freeswitch.org>
抄送：

Hi All,

I facing a strange problem.

Before, when calling Internal number, the name and number will both be displayed on the caller phone. When connected, only the name will display on the phone. At called phone, display the name and number. Seems fine.

But yesterday afternoon, when calling Internal number, only the number is displayed on the caller phone. When connected, display "Outbound Call" on the caller phone. At the called phone, everthing is the same. Display both the name and number.

I think, mabybe something configured wrong. So I try to restore back the configuration. seems the same. I have to re-install the last release stable 1.2.5.1 version on another server. total fresh setting. But found the same problem.

I checked the sip info.

The "Outbound Call" is in the 200 SDP message. the called is set to 

""Remote-Part-ID: "Outbound Call" <sip: 1234 at a.b.c.d>; ....... "

Not the correct called name.

Is there anything wrong?

Please help me.

Thanks!


2012-11-30



sparklezou
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-dev/attachments/20121203/931f2d39/attachment-0001.html