[Freeswitch-users] Running FreeSWITCH on softmodem

[Ken Rice]

Not to mention intel discontinued the chipset used on that card ages ago...
You¹ll be lucky to find them today


On 1/24/12 11:43 AM, "curriegrad2004" <curriegrad2004 at gmail.com> wrote:

> Don't even bother getting a x100p or it's clones either. It's been reported to
> work very poorly as an fxo. If you dug deeper you'll find that it's really a
> softmodem by Intel.
> 
> On 2012-01-24 9:02 AM, "Ken Rice" <krice at freeswitch.org> wrote:
>> Unfortunately most softmodems are not supported as a Telephony interface...
>> The problem is lack of drivers. The simple answer is it wont work...
>> 
>> You're best bet is to get an ATA with both FXO and FXS ports and connect via
>> SIP...
>> 
>> 
>> On 1/24/12 4:15 AM, "Sebastian Tarach" <starach at gmail.com> wrote:
>> 
>>> > Hello,
>>> >
>>> > I'm pretty new to the whole idea of using Linux as telephone central .
>>> > I tried to setup Asterisk at first but failed. Although I have managed
>>> > to install it I was unable to "call my computer". That's why I was
>>> > hoping to deal with FreeSWITCH better. Please tell a noob like myself
>>> > how to make this finally work. Keep in mind that something that is
>>> > clear to you to me is probably a dark magic. For instance in
>>> > installation guide there are mentioned few different ways to connect
>>> > to a modem. Which method should I use if it comes to my modem :
>>> >
>>> >
>>> > $ lspci -d 8086:24c6 -vvv
>>> > 00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M)
>>> > AC'97 Modem Controller (rev 03) (prog-if 00 [Generic])
>>> >         Subsystem: Toshiba America Info Systems Device 0001
>>> >         Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
>>> > ParErr- Stepping- SERR- FastB2B- DisINTx-
>>> >         Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>>>> >> TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
>>> >         Latency: 0
>>> >         Interrupt: pin B routed to IRQ 4
>>> >         Region 0: I/O ports at 2400 [size=256]
>>> >         Region 1: I/O ports at 2000 [size=128]
>>> >         Capabilities: [50] Power Management version 2
>>> >                 Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
>>> > PME(D0+,D1-,D2-,D3hot+,D3cold+)
>>> >                 Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
>>> >         Kernel driver in use: Intel ICH Modem
>>> >
>>> > Thanks in advance
>>> >
>>> > _________________________________________________________________________
>>> > Professional FreeSWITCH Consulting Services:
>>> > consulting at freeswitch.org
>>> > http://www.freeswitchsolutions.com
>>> >
>>> > 
>>> > 
>>> >
>>> > Official FreeSWITCH Sites
>>> > http://www.freeswitch.org
>>> > http://wiki.freeswitch.org
>>> > http://www.cluecon.com
>>> >
>>> > FreeSWITCH-users mailing list
>>> > FreeSWITCH-users at lists.freeswitch.org
>>> > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>> > UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>> > http://www.freeswitch.org
>> 
>> 
>> 
>> _________________________________________________________________________
>> Professional FreeSWITCH Consulting Services:
>> consulting at freeswitch.org
>> http://www.freeswitchsolutions.com
>> 
>> 
>> 
>> 
>> Official FreeSWITCH Sites
>> http://www.freeswitch.org
>> http://wiki.freeswitch.org
>> http://www.cluecon.com
>> 
>> FreeSWITCH-users mailing list
>> FreeSWITCH-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
> 
> 
> _________________________________________________________________________
> Professional FreeSWITCH Consulting Services:
> consulting at freeswitch.org
> http://www.freeswitchsolutions.com
> 
> 
> 
> 
> Official FreeSWITCH Sites
> http://www.freeswitch.org
> http://wiki.freeswitch.org
> http://www.cluecon.com
> 
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20120124/148c7acb/attachment.html