Hi As a new member of the forum, I am curious to know your experience with FXO/FXS cards. I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch. Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation? This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you. All advice would be greatly appreciated. Regards
Digium and sangoma cards are high quality and work greast with FS Michel On Thu, Sep 1, 2011 at 5:24 PM, ocset <ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
In the following order, most people usually recommend: 1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset <ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Just don't forget about Khomp even tho there is no support for T1 or J1. www.khomp.com Regards, JM On Thursday, September 1, 2011, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com <javascript:;>> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset <ocset@the800group.com<javascript:;>> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <javascript:;> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:
http://lists.freeswitch.org/mailman/options/freeswitch-users
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <javascript:;> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <javascript:;> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- João Mesquita FreeSWITCH™ Solutions
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc. For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example. On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, *Dario García* Consultor. CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards. On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset <ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Anthony Minessale II FreeSWITCH http://www.freeswitch.org/ ClueCon http://www.cluecon.com/ Twitter: http://twitter.com/FreeSWITCH_wire AIM: anthm MSN:anthony_minessale@hotmail.com GTALK/JABBER/PAYPAL:anthony.minessale@gmail.com IRC: irc.freenode.net #freeswitch FreeSWITCH Developer Conference sip:888@conference.freeswitch.org googletalk:conf+888@conference.freeswitch.org pstn:+19193869900
Thank you all for your replies. Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around. Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected. I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-) I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose? ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work? Thanks again for all your help and suggestions. On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Hi, for fxo's with the freeswitch I currently use: Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed. Darcy -----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice Thank you all for your replies. Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around. Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected. I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-) I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose? ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work? Thanks again for all your help and suggestions. On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm. Darcy <darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici covici@ccs.covici.com
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and it is quite reliable. If I get time later today, I will give it a try on a freeswitch. Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs, Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range. Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833 Darcy -----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm. Darcy <darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici covici@ccs.covici.com FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Darcy This info is very useful, especially since you have this setup running in production. One question - the two ATA devices (Grandstream & AudioCodes) are around the same price so could you give us some more info on why you would prefer the one over the other (besides the hook flash feature). Do they handle echo cancellation or do you deploy a separate solution for that? Thanks again for your help! On 09/03/2011 08:35 PM, Darcy wrote:
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and it is quite reliable. If I get time later today, I will give it a try on a freeswitch.
Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs,
Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range.
Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833
Darcy
-----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm.
Darcy<darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
they both handle echo suppression. The grandstream has a program that auto detects this and sets it up. The audio codes is primarily programmed using bootp while we have an auto provisioning system for the grandstream, we only use the audiocodes where we require hookflash. Darcy -----Original Message----- From: ocset Sent: Saturday, September 03, 2011 9:21 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice Darcy This info is very useful, especially since you have this setup running in production. One question - the two ATA devices (Grandstream & AudioCodes) are around the same price so could you give us some more info on why you would prefer the one over the other (besides the hook flash feature). Do they handle echo cancellation or do you deploy a separate solution for that? Thanks again for your help! On 09/03/2011 08:35 PM, Darcy wrote:
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and it is quite reliable. If I get time later today, I will give it a try on a freeswitch.
Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs,
Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range.
Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833
Darcy
-----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm.
Darcy<darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
And how do you flash the hook --is it some kind of built in feature code? Darcy <darcy@primrose.ws> wrote:
they both handle echo suppression. The grandstream has a program that auto detects this and sets it up. The audio codes is primarily programmed using bootp while we have an auto provisioning system for the grandstream, we only use the audiocodes where we require hookflash.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 9:21 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Darcy
This info is very useful, especially since you have this setup running in production.
One question - the two ATA devices (Grandstream & AudioCodes) are around the same price so could you give us some more info on why you would prefer the one over the other (besides the hook flash feature).
Do they handle echo cancellation or do you deploy a separate solution for that?
Thanks again for your help!
On 09/03/2011 08:35 PM, Darcy wrote:
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and it is quite reliable. If I get time later today, I will give it a try on a freeswitch.
Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs,
Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range.
Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833
Darcy
-----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm.
Darcy<darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici covici@ccs.covici.com
Khomp does it. As a matter of fact it registers an app to ease the pain of doinf flash based transfers, including when used with QSIG, EL7, E1LC and LineSide if you use those... JM On Sep 3, 2011 9:37 AM, <covici@ccs.covici.com> wrote:
And how do you flash the hook --is it some kind of built in feature code?
Darcy <darcy@primrose.ws> wrote:
they both handle echo suppression. The grandstream has a program that auto detects this and sets it up. The audio codes is primarily programmed using bootp while we have an auto
provisioning system for the grandstream, we only use the audiocodes where we require hookflash.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 9:21 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Darcy
This info is very useful, especially since you have this setup running in production.
One question - the two ATA devices (Grandstream & AudioCodes) are around the same price so could you give us some more info on why you would prefer the one over the other (besides the hook flash feature).
Do they handle echo cancellation or do you deploy a separate solution for that?
Thanks again for your help!
On 09/03/2011 08:35 PM, Darcy wrote:
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and
it is quite reliable. If I get time later today, I will give it a try on a freeswitch.
Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs,
Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range.
Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent
and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833
Darcy
-----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm.
Darcy<darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote:
One think you should consider also, is the FXO/FXS board that you will buy, you have to check compatibility with your server/pc.
For example openvox models A800P and A1200P has an issue with motherboard based on chipset H55 for example.
On 9/1/2011 9:59 PM, curriegrad2004 wrote:
In the following order, most people usually recommend:
1. Sangoma 2. Diginum/OpenVox 3. Building your own Tormenta Zapatel Card (Only for serious engineering types of people) from COTS
On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx <michel.daggelinckx@gmail.com> wrote:
Digium and sangoma cards are high quality and work greast with FS
Michel
On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote:
Hi
As a new member of the forum, I am curious to know your experience with FXO/FXS cards.
I have a SPA3102 and have configured it to work with FS, but it feels a bit like I am trying to make a square peg fit a round hole. I am hoping to implement FS at a business which currently has 4 POTS lines and would prefer to use an internal IDE card for the job of integrating these phone lines into FreeSwitch.
Has anyone got some advice on which cards I should be looking at that just "work" with FS? What about echo cancellation - is that something I should just cater for or does it depend on the client situation? What about software cancellation?
This seems like one of those times when too much choice is a bad thing and I need some guidance on what has worked for you.
All advice would be greatly appreciated.
Regards
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
----- No virus found in this message. Checked by AVG - www.avg.com Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11
-- Atentamente, Dario García Consultor.
CCCT, Nivel C2, Sector Yarey, Mz, Ofc. MZ03a. Caracas-Venezuela. Teléfono: +58 212 9081842 Cel: +58 412 2221515 dgarcia@anew.com.ve http://www.anew.com.ve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it?
John Covici covici@ccs.covici.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
What is Khomp exactly -- a freeswitch dialplan app or what? Sorry to be ignorant. João Mesquita <jmesquita@freeswitch.org> wrote:
Khomp does it. As a matter of fact it registers an app to ease the pain of doinf flash based transfers, including when used with QSIG, EL7, E1LC and LineSide if you use those...
JM On Sep 3, 2011 9:37 AM, <covici@ccs.covici.com> wrote:
And how do you flash the hook --is it some kind of built in feature code?
Darcy <darcy@primrose.ws> wrote:
they both handle echo suppression. The grandstream has a program that auto detects this and sets it up. The audio codes is primarily programmed using bootp while we have an auto
provisioning system for the grandstream, we only use the audiocodes where we require hookflash.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 9:21 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Darcy
This info is very useful, especially since you have this setup running in production.
One question - the two ATA devices (Grandstream & AudioCodes) are around the same price so could you give us some more info on why you would prefer the one over the other (besides the hook flash feature).
Do they handle echo cancellation or do you deploy a separate solution for that?
Thanks again for your help!
On 09/03/2011 08:35 PM, Darcy wrote:
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and
it is quite reliable. If I get time later today, I will give it a try on a freeswitch.
Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs,
Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range.
Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent
and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833
Darcy
-----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm.
Darcy<darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote:
If you are doing FXO and you already have an ATA working that might be as good as you'll get. Its nice to not have to deal with TDM if you can help it and most analog ATA are cheap and effective and much less painful to deal with than analog cards.
On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar <dgarcia@anew.com.ve> wrote: > One think you should consider also, is the FXO/FXS board that you will > buy, > you have to check compatibility with your server/pc. > > For example openvox models A800P and A1200P has an issue with > motherboard > based on chipset H55 for example. > > > On 9/1/2011 9:59 PM, curriegrad2004 wrote: > > In the following order, most people usually recommend: > > 1. Sangoma > 2. Diginum/OpenVox > 3. Building your own Tormenta Zapatel Card (Only for serious > engineering types of people) from COTS > > On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx > <michel.daggelinckx@gmail.com> wrote: > > Digium and sangoma cards are high quality and work greast with FS > > Michel > > > On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote: > > Hi > > As a new member of the forum, I am curious to know your experience with > FXO/FXS cards. > > I have a SPA3102 and have configured it to work with FS, but it feels a > bit like I am trying to make a square peg fit a round hole. I am hoping > to implement FS at a business which currently has 4 POTS lines and > would > prefer to use an internal IDE card for the job of integrating these > phone lines into FreeSwitch. > > Has anyone got some advice on which cards I should be looking at that > just "work" with FS? What about echo cancellation - is that something I > should just cater for or does it depend on the client situation? What > about software cancellation? > > This seems like one of those times when too much choice is a bad thing > and I need some guidance on what has worked for you. > > All advice would be greatly appreciated. > > Regards > > > FreeSWITCH-users mailing list > FreeSWITCH-users@lists.freeswitch.org > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users > UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users > http://www.freeswitch.org > > > FreeSWITCH-users mailing list > FreeSWITCH-users@lists.freeswitch.org > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users > UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users > http://www.freeswitch.org > > > > > FreeSWITCH-users mailing list > FreeSWITCH-users@lists.freeswitch.org > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users > UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users > http://www.freeswitch.org > > > ----- > No virus found in this message. > Checked by AVG - www.avg.com > Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11 > > > > > -- > Atentamente, > Dario García > Consultor. > > CCCT, Nivel C2, Sector Yarey, Mz, > Ofc. MZ03a. > Caracas-Venezuela. > Teléfono: +58 212 9081842 > Cel: +58 412 2221515 > dgarcia@anew.com.ve > http://www.anew.com.ve > > FreeSWITCH-users mailing list > FreeSWITCH-users@lists.freeswitch.org > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users > UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users > http://www.freeswitch.org > >
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it?
John Covici covici@ccs.covici.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
---------------------------------------------------- Alternatives:
----------------------------------------------------
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici covici@ccs.covici.com
Khomp is.a brazilian hardcard manufacturer. http://www.khomp.com.br It is the only one besides sangoma that officially supports freeswitch using their own development. On Sep 3, 2011 11:46 PM, <covici@ccs.covici.com> wrote:
What is Khomp exactly -- a freeswitch dialplan app or what? Sorry to be ignorant.
João Mesquita <jmesquita@freeswitch.org> wrote:
Khomp does it. As a matter of fact it registers an app to ease the pain of doinf flash based transfers, including when used with QSIG, EL7, E1LC and LineSide if you use those...
JM On Sep 3, 2011 9:37 AM, <covici@ccs.covici.com> wrote:
And how do you flash the hook --is it some kind of built in feature code?
Darcy <darcy@primrose.ws> wrote:
they both handle echo suppression. The grandstream has a program that auto detects this and sets it up. The audio codes is primarily programmed using bootp while we have an auto
provisioning system for the grandstream, we only use the audiocodes where we require hookflash.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 9:21 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Darcy
This info is very useful, especially since you have this setup running in production.
One question - the two ATA devices (Grandstream & AudioCodes) are around the same price so could you give us some more info on why you would prefer the one over the other (besides the hook flash feature).
Do they handle echo cancellation or do you deploy a separate solution for that?
Thanks again for your help!
On 09/03/2011 08:35 PM, Darcy wrote:
The grandstream has hookflash timers, but I have never been able to get it to work and info back from grandstream indicates is is not a pending implementation. For cases where I require a hook flash I use the audio codes fxo gateways. I never tested it on the freeswitch, we have own ap we wrote to handle it, we were doing this before we discovered freeswitch. I know it works and
it is quite reliable. If I get time later today, I will give it a try on a freeswitch.
Brand: AudioCodes Mfr's SKU: MP114/4O/SIP VoIP SIP Gateway, 4x FXO, 1x WAN, LBR Codecs,
Here are the options you have for using it. they have a variety of configurations, fxo/fxs combos a 4 port is in the 375 range.
Hook Flash Option [HookFlashOption] Supported hook-flash Transport Type (method by which hook-flash is sent
and received). Valid options include: 0 = Hook-Flash indication isn’t sent (default) 1 = Send proprietary INFO message with Hook-Flash indication 4 = RFC 2833
Darcy
-----Original Message----- From: covici@ccs.covici.com Sent: Saturday, September 03, 2011 7:06 AM To: FreeSWITCH Users Help Subject: Re: [Freeswitch-users] FXO/FXS card advice
Does this ata support picking up call waiting while in a call from the fxo? If it were to do that, I would get one right away. The Digium FXO card I have has problems doing this with freetdm.
Darcy<darcy@primrose.ws> wrote:
Hi, for fxo's with the freeswitch I currently use:
Mfr's SKU: GXW4104 Brand: Grandstream 4 x FXO Gateway, 2 x LAN, 1 or 2 stage dialing, G.168 echo cancellation
They work exceptionally well, easy to configure and can be auto configured if you are into that, we are. You can also get an 8 port version. I pay 220 for the 4 port and 300 for the 8 port. I have quite a few of them deployed.
Darcy
-----Original Message----- From: ocset Sent: Saturday, September 03, 2011 1:38 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] FXO/FXS card advice
Thank you all for your replies.
Anthony, you reply has left me uncertain again. All of the ATA's listed here (wiki.freeswitch.org/wiki/Interop_List) seem to have some limitations and bugs which have to worked around.
Your reply suggests that buying a OpenVox A400P04 card (currently only $219 for 4 FXO's) would be more difficult to install and maintain that 4 ATA's. I would have thought that the FXS/FXO cards were engineered to work with Freeswitch/Asterisk etc. without limitations like caller-id not working or call-transfer not working as expected.
I can see the benefit of an ATA since I can add them on as needed with little or no hassle (except for the large power board to plug them all into:-)
I have only just got the SPA3102 receiving incoming calls and I am no expert in either solution but would have thought that a 4 port FXO card would be easier as it is made to purpose?
ps. the PAP2T seems to be one of the better Linksys ATA's from the list of features that work?
Thanks again for all your help and suggestions.
On 09/03/2011 05:54 AM, Anthony Minessale wrote: > If you are doing FXO and you already have an ATA working that might be > as good as you'll get. > Its nice to not have to deal with TDM if you can help it and most > analog ATA are cheap and effective and much less painful to deal with > than analog cards. > > > > On Fri, Sep 2, 2011 at 8:39 AM, Saugort Dario Garcia Tovar > <dgarcia@anew.com.ve> wrote: >> One think you should consider also, is the FXO/FXS board that you will >> buy, >> you have to check compatibility with your server/pc. >> >> For example openvox models A800P and A1200P has an issue with >> motherboard >> based on chipset H55 for example. >> >> >> On 9/1/2011 9:59 PM, curriegrad2004 wrote: >> >> In the following order, most people usually recommend: >> >> 1. Sangoma >> 2. Diginum/OpenVox >> 3. Building your own Tormenta Zapatel Card (Only for serious >> engineering types of people) from COTS >> >> On Thu, Sep 1, 2011 at 8:50 AM, Michel Daggelinckx >> <michel.daggelinckx@gmail.com> wrote: >> >> Digium and sangoma cards are high quality and work greast with FS >> >> Michel >> >> >> On Thu, Sep 1, 2011 at 5:24 PM, ocset<ocset@the800group.com> wrote: >> >> Hi >> >> As a new member of the forum, I am curious to know your experience with >> FXO/FXS cards. >> >> I have a SPA3102 and have configured it to work with FS, but it feels a >> bit like I am trying to make a square peg fit a round hole. I am hoping >> to implement FS at a business which currently has 4 POTS lines and >> would >> prefer to use an internal IDE card for the job of integrating these >> phone lines into FreeSwitch. >> >> Has anyone got some advice on which cards I should be looking at that >> just "work" with FS? What about echo cancellation - is that something I >> should just cater for or does it depend on the client situation? What >> about software cancellation? >> >> This seems like one of those times when too much choice is a bad thing >> and I need some guidance on what has worked for you. >> >> All advice would be greatly appreciated. >> >> Regards >> >> >> FreeSWITCH-users mailing list >> FreeSWITCH-users@lists.freeswitch.org >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users >> UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users >> http://www.freeswitch.org >> >> >> FreeSWITCH-users mailing list >> FreeSWITCH-users@lists.freeswitch.org >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users >> UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users >> http://www.freeswitch.org >> >> >> >> >> FreeSWITCH-users mailing list >> FreeSWITCH-users@lists.freeswitch.org >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users >> UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users >> http://www.freeswitch.org >> >> >> ----- >> No virus found in this message. >> Checked by AVG - www.avg.com >> Version: 10.0.1392 / Virus Database: 1520/3872 - Release Date: 09/02/11 >> >> >> >> >> -- >> Atentamente, >> Dario García >> Consultor. >> >> CCCT, Nivel C2, Sector Yarey, Mz, >> Ofc. MZ03a. >> Caracas-Venezuela. >> Teléfono: +58 212 9081842 >> Cel: +58 412 2221515 >> dgarcia@anew.com.ve >> http://www.anew.com.ve >> >> FreeSWITCH-users mailing list >> FreeSWITCH-users@lists.freeswitch.org >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users >> UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users >> http://www.freeswitch.org >> >> >
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it?
John Covici covici@ccs.covici.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE: http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
---------------------------------------------------- Alternatives:
----------------------------------------------------
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Your life is like a penny. You're going to lose it. The question is: How do you spend it?
John Covici covici@ccs.covici.com
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
On 09/04/2011 08:35 AM, João Mesquita wrote:
Khomp does it. As a matter of fact it registers an app to ease the pain of doinf flash based transfers, including when used with QSIG, EL7, E1LC and LineSide if you use those...
JM
Does Khomp implement those protocols, or are you just saying hey interwork well with them? Steve
They do implement those protocols either on the DSP level such as R2 based or via their low level API called K3L. The API is what talks to mod_khomp. JM On Sep 4, 2011 2:54 AM, "Steve Underwood" <steveu@coppice.org> wrote:
On 09/04/2011 08:35 AM, João Mesquita wrote:
Khomp does it. As a matter of fact it registers an app to ease the pain of doinf flash based transfers, including when used with QSIG, EL7, E1LC and LineSide if you use those...
JM
Does Khomp implement those protocols, or are you just saying hey interwork well with them?
Steve
FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
participants (9)
-
Anthony Minessale
-
covici＠ccs.covici.com
-
curriegrad2004
-
Darcy
-
João Mesquita
-
Michel Daggelinckx
-
ocset
-
Saugort Dario Garcia Tovar
-
Steve Underwood