Freeswitch / Zywall USG100 problems
Just wondering if anyone here can help. I replaced a Linksys/Cisco RV042 router with a Zywall USG100. It solved a lot but broke Freeswitch badly. Yes I ran traces, etc. Both routers are set to use a static wan and no natting, ext-ip-sip/rtp are the wan static address. Just checking of anyone knows of a solution for one of these: 1. If I turn off ALG I cannot make a call or receive calls, the traces shows time outs. No firewall issues, nothing in any log to show the issue, 2. If I do have ALG on I can make calls but the HOLD button no longer works. Phone (Linksys SPA962) says "Trying to Hold" then times out. 3. With ALG on (so I can make calls) when I call out the call drops in the middle of a conversation between 30 seconds and 5 minutes. Been battling this and hope someone has already solved one of these. Thanks! Mario
The router is using natting, I meant freeswitch uses -nonat On Mar 9, 2011, at 12:16 PM, Mario G wrote:
Just wondering if anyone here can help. I replaced a Linksys/Cisco RV042 router with a Zywall USG100. It solved a lot but broke Freeswitch badly. Yes I ran traces, etc. Both routers are set to use a static wan and no natting, ext-ip-sip/rtp are the wan static address. Just checking of anyone knows of a solution for one of these:
1. If I turn off ALG I cannot make a call or receive calls, the traces shows time outs. No firewall issues, nothing in any log to show the issue,
2. If I do have ALG on I can make calls but the HOLD button no longer works. Phone (Linksys SPA962) says "Trying to Hold" then times out.
3. With ALG on (so I can make calls) when I call out the call drops in the middle of a conversation between 30 seconds and 5 minutes.
Been battling this and hope someone has already solved one of these. Thanks! Mario _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny. -MC On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta < fernando.berretta@gmail.com> wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Michael, Thanks for your valuable recommendation Best Regards, Fernando On 3/11/2011 6:41 PM, Michael Collins wrote:
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny.
-MC
On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com <mailto:fernando.berretta@gmail.com>> wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice. Diego Toro http://voipensando.blogspot.com/ --- On Fri, 3/11/11, Fernando Berretta <fernando.berretta@gmail.com> wrote: From: Fernando Berretta <fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM Michael, Thanks for your valuable recommendation Best Regards, Fernando On 3/11/2011 6:41 PM, Michael Collins wrote: If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny. -MC On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com> wrote: Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org -----Inline Attachment Follows----- _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Diego, Thanks for your answer It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ? Best Regards, Fernando On 3/12/2011 11:35 AM, Diego Toro wrote:
I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice.
Diego Toro http://voipensando.blogspot.com/
--- On *Fri, 3/11/11, Fernando Berretta /<fernando.berretta@gmail.com>/* wrote:
From: Fernando Berretta <fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM
Michael,
Thanks for your valuable recommendation
Best Regards, Fernando
On 3/11/2011 6:41 PM, Michael Collins wrote:
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny.
-MC
On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com </mc/compose?to=fernando.berretta@gmail.com>> wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Sangoma's PRI (E1) cards are supported under Windows. However, I've had some problems with the sangoma_isdn module for some time, so I havn't used it in about 6 months (it was only in a lab anyway). /Peter Från: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] För Fernando Berretta Skickat: den 14 mars 2011 13:11 Till: FreeSWITCH Users Help Ämne: Re: [Freeswitch-users] FreeSwitch for Windows Diego, Thanks for your answer It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ? Best Regards, Fernando On 3/12/2011 11:35 AM, Diego Toro wrote: I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice. Diego Toro http://voipensando.blogspot.com/ --- On Fri, 3/11/11, Fernando Berretta <fernando.berretta@gmail.com><mailto:fernando.berretta@gmail.com> wrote: From: Fernando Berretta <fernando.berretta@gmail.com><mailto:fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org><mailto:freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM Michael, Thanks for your valuable recommendation Best Regards, Fernando On 3/11/2011 6:41 PM, Michael Collins wrote: If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny. -MC On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com</mc/compose?to=fernando.berretta@gmail.com>> wrote: Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org</mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org</mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org -----Inline Attachment Follows----- _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org</mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org<mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org !DSPAM:4d7e069b32762783310086!
Hi Fernando, I have not used other cards, I have used sangoma cards with excelent support from sangoma's staff. Diego Toro http://voipensando.blogspot.com/ --- On Mon, 3/14/11, Peter Olsson <peter.olsson@visionutveckling.se> wrote: From: Peter Olsson <peter.olsson@visionutveckling.se> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "'FreeSWITCH Users Help'" <freeswitch-users@lists.freeswitch.org> Date: Monday, March 14, 2011, 7:22 AM Sangoma’s PRI (E1) cards are supported under Windows. However, I’ve had some problems with the sangoma_isdn module for some time, so I havn’t used it in about 6 months (it was only in a lab anyway). /Peter Från: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] För Fernando Berretta Skickat: den 14 mars 2011 13:11 Till: FreeSWITCH Users Help Ämne: Re: [Freeswitch-users] FreeSwitch for Windows Diego, Thanks for your answer It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ? Best Regards, Fernando On 3/12/2011 11:35 AM, Diego Toro wrote: I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice. Diego Toro http://voipensando.blogspot.com/ --- On Fri, 3/11/11, Fernando Berretta <fernando.berretta@gmail.com> wrote: From: Fernando Berretta <fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PMMichael, Thanks for your valuable recommendation Best Regards, Fernando On 3/11/2011 6:41 PM, Michael Collins wrote: If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny. -MCOn Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com> wrote:Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________FreeSWITCH-users mailing listFreeSWITCH-users@lists.freeswitch.orghttp://lists.freeswitch.org/mailman/listinfo/freeswitch-usersUNSUBSCRIBE:htt... -----Inline Attachment Follows-----_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________FreeSWITCH-users mailing listFreeSWITCH-users@lists.freeswitch.orghttp://lists.freeswitch.org/mailman/listinfo/freeswitch-usersUNSUBSCRIBE:htt... -----Inline Attachment Follows----- _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Hi Fernando, I have not used other cards, I have used sangoma cards with excelent support from sangoma's staff. Diego Toro http://voipensando.blogspot.com/ --- On Mon, 3/14/11, Peter Olsson <peter.olsson@visionutveckling.se> wrote: From: Peter Olsson <peter.olsson@visionutveckling.se> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "'FreeSWITCH Users Help'" <freeswitch-users@lists.freeswitch.org> Date: Monday, March 14, 2011, 7:22 AM Sangoma’s PRI (E1) cards are supported under Windows. However, I’ve had some problems with the sangoma_isdn module for some time, so I havn’t used it in about 6 months (it was only in a lab anyway). /Peter Från: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] För Fernando Berretta Skickat: den 14 mars 2011 13:11 Till: FreeSWITCH Users Help Ämne: Re: [Freeswitch-users] FreeSwitch for Windows Diego, Thanks for your answer It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ? Best Regards, Fernando On 3/12/2011 11:35 AM, Diego Toro wrote: I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice. Diego Toro http://voipensando.blogspot.com/ --- On Fri, 3/11/11, Fernando Berretta <fernando.berretta@gmail.com> wrote: From: Fernando Berretta <fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PMMichael, Thanks for your valuable recommendation Best Regards, Fernando On 3/11/2011 6:41 PM, Michael Collins wrote: If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny. -MCOn Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com> wrote:Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________FreeSWITCH-users mailing listFreeSWITCH-users@lists.freeswitch.orghttp://lists.freeswitch.org/mailman/listinfo/freeswitch-usersUNSUBSCRIBE:htt... -----Inline Attachment Follows-----_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________FreeSWITCH-users mailing listFreeSWITCH-users@lists.freeswitch.orghttp://lists.freeswitch.org/mailman/listinfo/freeswitch-usersUNSUBSCRIBE:htt... -----Inline Attachment Follows----- _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Diego, Thanks for your information, I'm gonna contact sangoma support to get more information. Best Regards, Fernando On 3/14/2011 11:08 AM, Diego Toro wrote:
Hi Fernando, I have not used other cards, I have used sangoma cards with excelent support from sangoma's staff.
Diego Toro http://voipensando.blogspot.com/
--- On *Mon, 3/14/11, Peter Olsson /<peter.olsson@visionutveckling.se>/* wrote:
From: Peter Olsson <peter.olsson@visionutveckling.se> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "'FreeSWITCH Users Help'" <freeswitch-users@lists.freeswitch.org> Date: Monday, March 14, 2011, 7:22 AM
Sangoma’s PRI (E1) cards are supported under Windows. However, I’ve had some problems with the sangoma_isdn module for some time, so I havn’t used it in about 6 months (it was only in a lab anyway).
/Peter
*Från:*freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] *För *Fernando Berretta *Skickat:* den 14 mars 2011 13:11 *Till:* FreeSWITCH Users Help *Ämne:* Re: [Freeswitch-users] FreeSwitch for Windows
Diego,
Thanks for your answer
It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ?
Best Regards, Fernando
On 3/12/2011 11:35 AM, Diego Toro wrote:
I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice.
Diego Toro http://voipensando.blogspot.com/
--- On *Fri, 3/11/11, Fernando Berretta /<fernando.berretta@gmail.com> </mc/compose?to=fernando.berretta@gmail.com>/* wrote:
From: Fernando Berretta <fernando.berretta@gmail.com> </mc/compose?to=fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> </mc/compose?to=freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM
Michael,
Thanks for your valuable recommendation
Best Regards, Fernando
On 3/11/2011 6:41 PM, Michael Collins wrote:
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny.
-MC
On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com> wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org>
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
!DSPAM:4d7e069b32762783310086!
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Hi Fernando, You should have no problems to use FS + Sangoma cards on Windows. The latest libsng_isdn for Windows can be downloaded from here: ftp://ftp.sangoma.com/WINDOWS/libsng_isdn/libsng_isdn-7.1.0-win32.exe Instructions on how to install FS can be found here: http://wiki.freeswitch.org/wiki/Installation_for_Windows Once you have compiled Freeswitch and installed libsng_isdn, you can to go to the libs/freetdm directory and open the Visual Studio project file there, compile FreeTDM core and ftmod_sangoma_isdn module. Regards, David *David Yat Sin, BEng* */Senior Software Engineer/* Sangoma Technologies 100 Renfrew Drive, Suite 100, Markham, ON L3R 9R6 Canada t. +1 800 388 2475 x119 t. +1 905 474 1990 x119 f. +1 905 474 9223 Description: SANGOMA <http://www.sangoma.com/contact?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> Products <http://sangoma.com/products?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Solutions <http://sangoma.com/solutions?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Events <http://sangoma.com/about_us/events?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Contact <http://www.sangoma.com/contact?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Wiki <http://wiki.sangoma.com/?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Facebook <http://www.facebook.com/pages/Sangoma-VoIP-Cards/43578453335?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> | Twitter <http://www.twitter.com/sangoma?utm_source=signature&utm_medium=email&utm_campaign=email%2Bsignatures> On 3/14/2011 10:08 AM, Diego Toro wrote:
Hi Fernando, I have not used other cards, I have used sangoma cards with excelent support from sangoma's staff.
Diego Toro http://voipensando.blogspot.com/
--- On *Mon, 3/14/11, Peter Olsson /<peter.olsson@visionutveckling.se>/* wrote:
From: Peter Olsson <peter.olsson@visionutveckling.se> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "'FreeSWITCH Users Help'" <freeswitch-users@lists.freeswitch.org> Date: Monday, March 14, 2011, 7:22 AM
Sangoma’s PRI (E1) cards are supported under Windows. However, I’ve had some problems with the sangoma_isdn module for some time, so I havn’t used it in about 6 months (it was only in a lab anyway).
/Peter
*Från:*freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] *För *Fernando Berretta *Skickat:* den 14 mars 2011 13:11 *Till:* FreeSWITCH Users Help *Ämne:* Re: [Freeswitch-users] FreeSwitch for Windows
Diego,
Thanks for your answer
It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ?
Best Regards, Fernando
On 3/12/2011 11:35 AM, Diego Toro wrote:
I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice.
Diego Toro http://voipensando.blogspot.com/
--- On *Fri, 3/11/11, Fernando Berretta /<fernando.berretta@gmail.com> </mc/compose?to=fernando.berretta@gmail.com>/* wrote:
From: Fernando Berretta <fernando.berretta@gmail.com> </mc/compose?to=fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> </mc/compose?to=freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM
Michael,
Thanks for your valuable recommendation
Best Regards, Fernando
On 3/11/2011 6:41 PM, Michael Collins wrote:
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny.
-MC
On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com> wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org>
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
!DSPAM:4d7e069b32762783310086!
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org </mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
MFC-R2 via the openr2 stack works very well in Windows with Sangoma cards. There is no formal release yet though (should be ready in about a month) but the code is not changing any more, the only reason to not have a release is that we want a Windows installer for the openr2 stack. You need to build the stack yourself using CMake for Windows and Visual Studio in the meantime. Moises Silva Senior Software Engineer Sangoma Technologies Inc. | 100 Renfrew Drive, Suite 100, Markham ON L3R 9R6 Canada t. 1 905 474 1990 x128 | e. moy@sangoma.com On Mon, Mar 14, 2011 at 8:10 AM, Fernando Berretta < fernando.berretta@gmail.com> wrote:
Diego,
Thanks for your answer
It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ?
Best Regards, Fernando
On 3/12/2011 11:35 AM, Diego Toro wrote:
I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice.
Diego Toro http://voipensando.blogspot.com/
--- On *Fri, 3/11/11, Fernando Berretta <fernando.berretta@gmail.com><fernando.berretta@gmail.com> * wrote:
From: Fernando Berretta <fernando.berretta@gmail.com><fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org><freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM
Michael,
Thanks for your valuable recommendation
Best Regards, Fernando
On 3/11/2011 6:41 PM, Michael Collins wrote:
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny.
-MC
On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta < fernando.berretta@gmail.com<http://mc/compose?to=fernando.berretta@gmail.com>
wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org<http://mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing listFreeSWITCH-users@lists.freeswitch.org <http://mc/compose?to=FreeSWITCH-users@lists.freeswitch.org>http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-usershttp://www.frees...
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org<http://mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing listFreeSWITCH-users@lists.freeswitch.orghttp://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-usershttp://www.frees...
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Moises, Thanks for your answer, it is very interesting, I'm gonna try it ASAP. Best Regards, Fernando On 3/14/2011 1:39 PM, Moises Silva wrote:
MFC-R2 via the openr2 stack works very well in Windows with Sangoma cards.
There is no formal release yet though (should be ready in about a month) but the code is not changing any more, the only reason to not have a release is that we want a Windows installer for the openr2 stack. You need to build the stack yourself using CMake for Windows and Visual Studio in the meantime.
Moises Silva Senior Software Engineer Sangoma Technologies Inc. | 100 Renfrew Drive, Suite 100, Markham ON L3R 9R6 Canada t. 1 905 474 1990 x128 | e. moy@sangoma.com <mailto:moy@sangoma.com>
On Mon, Mar 14, 2011 at 8:10 AM, Fernando Berretta <fernando.berretta@gmail.com <mailto:fernando.berretta@gmail.com>> wrote:
Diego,
Thanks for your answer
It is possible to use also boards like Digium, OpenVox or any other similar one ? What about E1 cards ? have you tried one of them over Windows ? MFC R2 ?
Best Regards, Fernando
On 3/12/2011 11:35 AM, Diego Toro wrote:
I don't think like Mr. Colling, I have FS on Windows in production since two year using sangoma cards (FXO, FXS) and works fine. Windows is a good choice.
Diego Toro http://voipensando.blogspot.com/
--- On *Fri, 3/11/11, Fernando Berretta /<fernando.berretta@gmail.com> <mailto:fernando.berretta@gmail.com>/* wrote:
From: Fernando Berretta <fernando.berretta@gmail.com> <mailto:fernando.berretta@gmail.com> Subject: Re: [Freeswitch-users] FreeSwitch for Windows To: "FreeSWITCH Users Help" <freeswitch-users@lists.freeswitch.org> <mailto:freeswitch-users@lists.freeswitch.org> Date: Friday, March 11, 2011, 4:54 PM
Michael,
Thanks for your valuable recommendation
Best Regards, Fernando
On 3/11/2011 6:41 PM, Michael Collins wrote:
If you plan on using TDM then I'd recommend you stay away from Windows. Sangoma and Digium/clone cards are all geared toward a Linux environment. Stay away from the exotic OSes and use something simple like CentOS 5.5 or Debian Lenny.
-MC
On Wed, Mar 9, 2011 at 1:38 PM, Fernando Berretta <fernando.berretta@gmail.com <http://mc/compose?to=fernando.berretta@gmail.com>> wrote:
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <http://mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <http://mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-----Inline Attachment Follows-----
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <http://mc/compose?to=FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Dear Fernando, İ'm using FS on 4 different Server's since over 1 year successfully. My last server is a 64 bit platform and all things that i use worked fine for me. The only thing that i see is some file or folder path are not correctly and formated for Unix/Linux systems. This one must be changed manual for Windows path name. For example sounds/xxx/.... and so on the file or path can not be found on Windows. You see that in the console of FS. But i changed it manual to sounds\xxx\.... and all things work fine. Also some modules that i need worked for me. But with boards or other hardware i can not tell you something, because i don't use it. Kind regards Erkan -----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Fernando Berretta Sent: Wednesday, March 09, 2011 11:38 PM To: FreeSWITCH Users Help Subject: [Freeswitch-users] FreeSwitch for Windows Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
File paths in Windows should work with either / or \ without any problems, I've never seen any issues with this, and I've been running FS on Windows for at least a year now. /Peter -----Ursprungligt meddelande----- Från: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] För Erkan Ünlü Skickat: den 14 mars 2011 09:20 Till: FreeSWITCH Users Help Ämne: Re: [Freeswitch-users] FreeSwitch for Windows Dear Fernando, İ'm using FS on 4 different Server's since over 1 year successfully. My last server is a 64 bit platform and all things that i use worked fine for me. The only thing that i see is some file or folder path are not correctly and formated for Unix/Linux systems. This one must be changed manual for Windows path name. For example sounds/xxx/.... and so on the file or path can not be found on Windows. You see that in the console of FS. But i changed it manual to sounds\xxx\.... and all things work fine. Also some modules that i need worked for me. But with boards or other hardware i can not tell you something, because i don't use it. Kind regards Erkan -----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Fernando Berretta Sent: Wednesday, March 09, 2011 11:38 PM To: FreeSWITCH Users Help Subject: [Freeswitch-users] FreeSwitch for Windows Hi, I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ? Thanks for your time, Best Regards, Fernando _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org !DSPAM:4d7dd1c232761971858288!
Erkan, Thanks for your advice, I'll take care of sounds folder path Best Regards, Fernando On 3/14/2011 5:19 AM, Erkan Ünlü wrote:
Dear Fernando,
İ'm using FS on 4 different Server's since over 1 year successfully. My last server is a 64 bit platform and all things that i use worked fine for me.
The only thing that i see is some file or folder path are not correctly and formated for Unix/Linux systems. This one must be changed manual for Windows path name.
For example sounds/xxx/.... and so on the file or path can not be found on Windows. You see that in the console of FS. But i changed it manual to sounds\xxx\.... and all things work fine. Also some modules that i need worked for me.
But with boards or other hardware i can not tell you something, because i don't use it.
Kind regards Erkan
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Fernando Berretta Sent: Wednesday, March 09, 2011 11:38 PM To: FreeSWITCH Users Help Subject: [Freeswitch-users] FreeSwitch for Windows
Hi,
I'm newbie in FreeSwitch and would like to know if freeswitch could be used for production under Windows platforms ? telephony boards like Digium / OpenVox, Sangoma, etc are going to work ok under Windows ? is there any problem / limitation ? E1 MFCR2 Trunk works ?
Thanks for your time, Best Regards, Fernando
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Was this thread hijacked? On Mar 9, 2011, at 12:20 PM, Mario G wrote:
The router is using natting, I meant freeswitch uses -nonat
On Mar 9, 2011, at 12:16 PM, Mario G wrote:
Just wondering if anyone here can help. I replaced a Linksys/Cisco RV042 router with a Zywall USG100. It solved a lot but broke Freeswitch badly. Yes I ran traces, etc. Both routers are set to use a static wan and no natting, ext-ip-sip/rtp are the wan static address. Just checking of anyone knows of a solution for one of these:
1. If I turn off ALG I cannot make a call or receive calls, the traces shows time outs. No firewall issues, nothing in any log to show the issue,
2. If I do have ALG on I can make calls but the HOLD button no longer works. Phone (Linksys SPA962) says "Trying to Hold" then times out.
3. With ALG on (so I can make calls) when I call out the call drops in the middle of a conversation between 30 seconds and 5 minutes.
Been battling this and hope someone has already solved one of these. Thanks! Mario _______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Mario G wrote:
Was this thread hijacked? Mario, I just can't believe the mods here let your thread get hijacked!
----- FreeSWITCH hosted on a Seagate DockStar with OpenWRT. -- View this message in context: http://freeswitch-users.2379917.n2.nabble.com/Freeswitch-Zywall-USG100-probl... Sent from the freeswitch-users mailing list archive at Nabble.com.
participants (9)
-
David Yat Sin
-
Diego Toro
-
Erkan Ünlü
-
Fernando Berretta
-
Mario G
-
mazilo
-
Michael Collins
-
Moises Silva
-
Peter Olsson