Re: [Freeswitch-users] Grandstream gateways
Thank you for those tips, I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that? I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma, Thank you all.. Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use? On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com> Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com> Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
You haven't really put it into production for more than one year. The issue with GXW4108 is that after some time, say a couple of months, either all FXO ports not working, or worse, some FXO ports not working, but after power recycling, they will come back to work for some time until on strike again at some time you have no control. This had been reported for a couple of years without improvement. Go google search you will find out, this has happened to many GXW4108 users. On Wed, Nov 25, 2009 at 3:16 PM, Samuel Mukoti <samuelmukoti@gmail.com>wrote:
Thank you for those tips,
I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that?
I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma,
Thank you all..
Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use?
On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com> Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com> Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
Kill it, sunshine. /b On Nov 25, 2009, at 2:40 PM, Chris Chen wrote:
You haven't really put it into production for more than one year. The issue with GXW4108 is that after some time, say a couple of months, either all FXO ports not working, or worse, some FXO ports not working, but after power recycling, they will come back to work for some time until on strike again at some time you have no control.
This had been reported for a couple of years without improvement. Go google search you will find out, this has happened to many GXW4108 users.
Hello, Samuel: We also have some GXW4104 gateways, in small production/testing environments; our caller id works fine and none of them has failed in over a year of being used. The thing that i dislike about the GXW series is that it has no support for early media. Everyone: What FXO devices do you currently use / recommend? 2009/11/25 Chris Chen <chris.chen2004@gmail.com>
You haven't really put it into production for more than one year. The issue with GXW4108 is that after some time, say a couple of months, either all FXO ports not working, or worse, some FXO ports not working, but after power recycling, they will come back to work for some time until on strike again at some time you have no control.
This had been reported for a couple of years without improvement. Go google search you will find out, this has happened to many GXW4108 users.
On Wed, Nov 25, 2009 at 3:16 PM, Samuel Mukoti <samuelmukoti@gmail.com>wrote:
Thank you for those tips,
I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that?
I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma,
Thank you all..
Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use?
On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM,
freeswitch-users-request@lists.freeswitch.org
wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com> Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com> Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
I had hear about Welltech (http://www.welltech.com/default.aspx) gateways but I don't have any experience with them. Someone know ?, any experience... Diego Toro http://lacarretade.blogspot.com/ --- On Wed, 11/25/09, Milena <testeador01@gmail.com> wrote: From: Milena <testeador01@gmail.com> Subject: Re: [Freeswitch-users] Grandstream gateways To: freeswitch-users@lists.freeswitch.org Date: Wednesday, November 25, 2009, 4:00 PM Hello, Samuel: We also have some GXW4104 gateways, in small production/testing environments; our caller id works fine and none of them has failed in over a year of being used. The thing that i dislike about the GXW series is that it has no support for early media. Everyone: What FXO devices do you currently use / recommend? 2009/11/25 Chris Chen <chris.chen2004@gmail.com> You haven't really put it into production for more than one year. The issue with GXW4108 is that after some time, say a couple of months, either all FXO ports not working, or worse, some FXO ports not working, but after power recycling, they will come back to work for some time until on strike again at some time you have no control. This had been reported for a couple of years without improvement. Go google search you will find out, this has happened to many GXW4108 users. On Wed, Nov 25, 2009 at 3:16 PM, Samuel Mukoti <samuelmukoti@gmail.com> wrote: Thank you for those tips, I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that? I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma, Thank you all.. Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use? On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go
the gateway route Grandstream or Audiocodes would work fine.
Audiocodes are a bit more telco grade. If you have 25 POTS incoming
you could use a 24FXO channel bank cross connected with Rhino T1
cards, or individual FXO gateways but you may have a hard time
finding 24 ports of FXO in a single GW. Best performing T1 cards in
my experience (thousands of deployments) are Sangoma. Your server
configuration looks fine.
Cory J. Andrews
Director New Market Initiatives
Sayers Media Group
VoIP Supply, LLC
454 Sonwil Drive
Buffalo, NY 14225
716-250-3402 OFFICE
716-630-1548 FAX
716-601-4474 MOBILE
candrews@sayersmedia.com
Have I exceeded your expectations? Please share your experience
with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document
attached hereto is intended only for the named recipient(s). It is
the property of the VoIP Supply, LLC and shall not be used,
disclosed or reproduced without the express written consent of VoIP
Supply, LLC. If you are not the intended recipient, nor the employee
or agent responsible for delivering this message in confidence to
the intended recipient(s), you are hereby notified that you have
received this transmittal in error, and any review, dissemination,
distribution or copying of this transmittal or its attachments is
strictly prohibited. If you have received this transmittal and/or
attachments in error, please notify me immediately by reply e-mail
or telephone and then delete this message, including any
attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY
14225 USA.
-----Original Message-----
From: freeswitch-users-bounces@lists.freeswitch.org
[mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of
Samuel Mukoti
Sent: Wednesday, November 25, 2009 2:40 PM
To: freeswitch-users@lists.freeswitch.org
Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200
extensions and 24 POTS incoming, also a T1 line once the telco guys
are ready. I wanted assistance with choosing the most appropriate
hardware. We already have about 150 analogue phones, and I was
wondering what's best? A couple of grandstream FXS GXW4024? Also for
my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma
or digium card? The best voice quality is paramount. Lastly for T1
what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM,
would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org
wrote:
Send FreeSWITCH-users mailing list submissions to
freeswitch-users@lists.freeswitch.org
To subscribe or unsubscribe via the World Wide Web, visit
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
or, via email, send a message with subject or body 'help' to
freeswitch-users-request@lists.freeswitch.org
You can reach the person managing the list at
freeswitch-users-owner@lists.freeswitch.org
When replying, please edit your Subject line so it is more specific
than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris)
2. Re: Handling the 302 Moved Temporarily response from
JavaScript (Michael Jerris)
3. Re: No NOTIFY MWI when registering via proxy. (Brian West)
4. Re: remote_media_ip variable not set (Michael Jerris)
5. Re: How to find whether the destination extension supports
encryption (Michael Jerris)
6. Re: Bypass_media and re_invite (srinivasula reddy)
7. Re: Handling the 302 Moved Temporarily response from
JavaScript (Stephen Crosby)
8. Re: Handling the 302 Moved Temporarily response from
JavaScript (Tihomir Culjaga)
---
-------------------------------------------------------------------
Message: 1
Date: Wed, 25 Nov 2009 12:44:46 -0500
From: Michael Jerris <mike@jerris.com>
Subject: Re: [Freeswitch-users] mod_conference kick to abort
invitations
To: freeswitch-users@lists.freeswitch.org
Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com>
Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members,
I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are
connected to the conference?
Is there no chance abort an invitation?
The kick command has no effect until the person I invited with the
dial command is connected.
Yes. I have one if anybody wants it, would let it go cheap. Works fine, but caller id is only the number, not the name part. Other than that works fine with astersik From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Diego Toro Sent: Wednesday, December 09, 2009 3:05 PM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Grandstream gateways I had hear about Welltech (http://www.welltech.com/default.aspx) gateways but I don't have any experience with them. Someone know ?, any experience... Diego Toro http://lacarretade.blogspot.com/ --- On Wed, 11/25/09, Milena <testeador01@gmail.com> wrote: From: Milena <testeador01@gmail.com> Subject: Re: [Freeswitch-users] Grandstream gateways To: freeswitch-users@lists.freeswitch.org Date: Wednesday, November 25, 2009, 4:00 PM Hello, Samuel: We also have some GXW4104 gateways, in small production/testing environments; our caller id works fine and none of them has failed in over a year of being used. The thing that i dislike about the GXW series is that it has no support for early media. Everyone: What FXO devices do you currently use / recommend? 2009/11/25 Chris Chen <chris.chen2004@gmail.com</mc/compose?to=chris.chen2004@gmail.com>> You haven't really put it into production for more than one year. The issue with GXW4108 is that after some time, say a couple of months, either all FXO ports not working, or worse, some FXO ports not working, but after power recycling, they will come back to work for some time until on strike again at some time you have no control. This had been reported for a couple of years without improvement. Go google search you will find out, this has happened to many GXW4108 users. On Wed, Nov 25, 2009 at 3:16 PM, Samuel Mukoti <samuelmukoti@gmail.com</mc/compose?to=samuelmukoti@gmail.com>> wrote: Thank you for those tips, I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that? I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma, Thank you all.. Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use? On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com</mc/compose?to=cory@voipsupply.com>> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com</mc/compose?to=candrews@sayersmedia.com>
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org</mc/compose?to=freeswitch-users-bounces@lists.freeswitch.org> [mailto:freeswitch-users-bounces@lists.freeswitch.org</mc/compose?to=freeswitch-users-bounces@lists.freeswitch.org>] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org</mc/compose?to=freeswitch-users@lists.freeswitch.org> Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti<http://twitter.com/samuelmukoti>
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org</mc/compose?to=freeswitch-users-request@lists.freeswitch.org> wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org</mc/compose?to=freeswitch-users@lists.freeswitch.org>
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org</mc/compose?to=freeswitch-users-request@lists.freeswitch.org>
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org</mc/compose?to=freeswitch-users-owner@lists.freeswitch.org>
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com</mc/compose?to=mike@jerris.com>> Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org</mc/compose?to=freeswitch-users@lists.freeswitch.org> Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com</mc/compose?to=1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com>> Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
@kendalll: CallerID number is fine for PSTN application. what model do you have? any experience w/ their 24 port FXS? i'm really looking for 24 ports FXS for PSTN application. aside from audiocodes, any brand can you recommend? the FXS must generate 12/16khz pulse metering signal. tks. -nandy On Thu, Dec 10, 2009 at 4:12 AM, Kendall Stauffer <ken@ksac.com> wrote:
Yes. I have one if anybody wants it, would let it go cheap.
Works fine, but caller id is only the number, not the name part. Other than that works fine with astersik
*From:* freeswitch-users-bounces@lists.freeswitch.org [mailto: freeswitch-users-bounces@lists.freeswitch.org] *On Behalf Of *Diego Toro *Sent:* Wednesday, December 09, 2009 3:05 PM
*To:* freeswitch-users@lists.freeswitch.org *Subject:* Re: [Freeswitch-users] Grandstream gateways
I had hear about Welltech (http://www.welltech.com/default.aspx) gateways but I don't have any experience with them.
Someone know ?, any experience...
Diego Toro http://lacarretade.blogspot.com/
--- On *Wed, 11/25/09, Milena <testeador01@gmail.com>* wrote:
From: Milena <testeador01@gmail.com> Subject: Re: [Freeswitch-users] Grandstream gateways To: freeswitch-users@lists.freeswitch.org Date: Wednesday, November 25, 2009, 4:00 PM
Hello,
Samuel: We also have some GXW4104 gateways, in small production/testing environments; our caller id works fine and none of them has failed in over a year of being used. The thing that i dislike about the GXW series is that it has no support for early media.
Everyone: What FXO devices do you currently use / recommend?
2009/11/25 Chris Chen <chris.chen2004@gmail.com<http://mc/compose?to=chris.chen2004@gmail.com>
You haven't really put it into production for more than one year. The issue with GXW4108 is that after some time, say a couple of months, either all FXO ports not working, or worse, some FXO ports not working, but after power recycling, they will come back to work for some time until on strike again at some time you have no control.
This had been reported for a couple of years without improvement. Go google search you will find out, this has happened to many GXW4108 users.
On Wed, Nov 25, 2009 at 3:16 PM, Samuel Mukoti <samuelmukoti@gmail.com<http://mc/compose?to=samuelmukoti@gmail.com>> wrote:
Thank you for those tips,
I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that?
I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma,
Thank you all..
Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use?
On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com<http://mc/compose?to=cory@voipsupply.com>> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com <http://mc/compose?to=candrews@sayersmedia.com>
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org<http://mc/compose?to=freeswitch-users-bounces@lists.freeswitch.org> [mailto:freeswitch-users-bounces@lists.freeswitch.org<http://mc/compose?to=freeswitch-users-bounces@lists.freeswitch.org>]
On Behalf Of
Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org<http://mc/compose?to=freeswitch-users@lists.freeswitch.org>
Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org<http://mc/compose?to=freeswitch-users-request@lists.freeswitch.org> wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org<http://mc/compose?to=freeswitch-users@lists.freeswitch.org>
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org<http://mc/compose?to=freeswitch-users-request@lists.freeswitch.org>
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org<http://mc/compose?to=freeswitch-users-owner@lists.freeswitch.org>
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com<http://mc/compose?to=mike@jerris.com>
Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org<http://mc/compose?to=freeswitch-users@lists.freeswitch.org> Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com<http://mc/compose?to=1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com>
Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
Samuel, FreeSWITCH has a Skype module that uses Skype client instances to connect to the Skype network, you can read about it at http://wiki.freeswitch.org/wiki/Skypiax As far as an official Skype module for non-Asterisk PBX-es, it looks like it is in beta right now - http://www.skype.com/business/products/pbx-systems/sip/ -AF -----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 1:17 PM Cc: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Grandstream gateways Thank you for those tips, I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that? I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma, Thank you all.. Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use? On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com> Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com> Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
On Nov 25, 2009, at 5:18 PM, Adam Ford wrote:
Samuel,
FreeSWITCH has a Skype module that uses Skype client instances to connect to the Skype network, you can read about it at http://wiki.freeswitch.org/wiki/Skypiax
As far as an official Skype module for non-Asterisk PBX-es, it looks like it is in beta right now - http://www.skype.com/business/products/pbx-systems/sip/
-AF
If by in beta you mean they turned off all the servers the beta testers could talk to, then yes, it is indeed. Mike
exactly On Wed, Nov 25, 2009 at 4:38 PM, Michael Jerris <mike@jerris.com> wrote:
On Nov 25, 2009, at 5:18 PM, Adam Ford wrote:
Samuel,
FreeSWITCH has a Skype module that uses Skype client instances to connect to the Skype network, you can read about it at http://wiki.freeswitch.org/wiki/Skypiax
As far as an official Skype module for non-Asterisk PBX-es, it looks like it is in beta right now - http://www.skype.com/business/products/pbx-systems/sip/
-AF
If by in beta you mean they turned off all the servers the beta testers could talk to, then yes, it is indeed.
Mike
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Anthony Minessale II FreeSWITCH http://www.freeswitch.org/ ClueCon http://www.cluecon.com/ Twitter: http://twitter.com/FreeSWITCH_wire AIM: anthm MSN:anthony_minessale@hotmail.com <MSN%3Aanthony_minessale@hotmail.com> GTALK/JABBER/PAYPAL:anthony.minessale@gmail.com<PAYPAL%3Aanthony.minessale@gmail.com> IRC: irc.freenode.net #freeswitch FreeSWITCH Developer Conference sip:888@conference.freeswitch.org <sip%3A888@conference.freeswitch.org> iax:guest@conference.freeswitch.org/888 googletalk:conf+888@conference.freeswitch.org<googletalk%3Aconf%2B888@conference.freeswitch.org> pstn:213-799-1400
Skype for SIP is just a SIP account you can get from skype that is somehow tied to skype, probably using the scary 2 year commerical endeavor to make skype work in asterisk. We should all thank Giovanni Maruzzelli for giving us a free solution. On Wed, Nov 25, 2009 at 4:18 PM, Adam Ford <lists@redbonez.net> wrote:
Samuel,
FreeSWITCH has a Skype module that uses Skype client instances to connect to the Skype network, you can read about it at http://wiki.freeswitch.org/wiki/Skypiax
As far as an official Skype module for non-Asterisk PBX-es, it looks like it is in beta right now - http://www.skype.com/business/products/pbx-systems/sip/
-AF
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 1:17 PM Cc: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Grandstream gateways
Thank you for those tips,
I do have some small setups using gxw4108 they work or, except CID doesn't seem to work. I will try the channel bank route - just don't know too much about the setup options or how you'd purchase the correct config, eg. For 150 FXS channel bank, can I get a single PCI card for that?
I may end up using the grandstream fxs gateways then use the T1 channel bank from sangoma,
Thank you all..
Lastly, I know asterisk now has an offical skype_ module, Is there anything similar I could use?
On 25 Nov,2009, at 9:52 PM, Cory Andrews <cory@voipsupply.com> wrote:
Samuel - you could go with FXS gateways or channel banks. If you go the gateway route Grandstream or Audiocodes would work fine. Audiocodes are a bit more telco grade. If you have 25 POTS incoming you could use a 24FXO channel bank cross connected with Rhino T1 cards, or individual FXO gateways but you may have a hard time finding 24 ports of FXO in a single GW. Best performing T1 cards in my experience (thousands of deployments) are Sangoma. Your server configuration looks fine.
Cory J. Andrews Director New Market Initiatives
Sayers Media Group VoIP Supply, LLC 454 Sonwil Drive Buffalo, NY 14225 716-250-3402 OFFICE 716-630-1548 FAX 716-601-4474 MOBILE candrews@sayersmedia.com
Have I exceeded your expectations? Please share your experience with my boss, Benjamin P. Sayers, CEO
NOTICE: The information contained in this email and any document attached hereto is intended only for the named recipient(s). It is the property of the VoIP Supply, LLC and shall not be used, disclosed or reproduced without the express written consent of VoIP Supply, LLC. If you are not the intended recipient, nor the employee or agent responsible for delivering this message in confidence to the intended recipient(s), you are hereby notified that you have received this transmittal in error, and any review, dissemination, distribution or copying of this transmittal or its attachments is strictly prohibited. If you have received this transmittal and/or attachments in error, please notify me immediately by reply e-mail or telephone and then delete this message, including any attachments. Our mailing address is 454 Sonwil Drive, Buffalo, NY 14225 USA.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Samuel Mukoti Sent: Wednesday, November 25, 2009 2:40 PM To: freeswitch-users@lists.freeswitch.org Subject: [Freeswitch-users] Grandstream gateways
Hi all,
I'm wanting to try out a my first large scale setup at the office, 200 extensions and 24 POTS incoming, also a T1 line once the telco guys are ready. I wanted assistance with choosing the most appropriate hardware. We already have about 150 analogue phones, and I was wondering what's best? A couple of grandstream FXS GXW4024? Also for my POTS lines, gxw4108 FXO gateway or is it better to buy a sangoma or digium card? The best voice quality is paramount. Lastly for T1 what cards are recommeded,
I was also proposing to use a Dell T116 Quad core intel i7 8G DRAM, would that perform? Or do I need hardware transcoding?
Thank you,
Sam
Twitter: twitter.com/samuelmukoti
On 25 Nov,2009, at 8:05 PM, freeswitch-users-request@lists.freeswitch.org wrote:
Send FreeSWITCH-users mailing list submissions to freeswitch-users@lists.freeswitch.org
To subscribe or unsubscribe via the World Wide Web, visit http://lists.freeswitch.org/mailman/listinfo/freeswitch-users or, via email, send a message with subject or body 'help' to freeswitch-users-request@lists.freeswitch.org
You can reach the person managing the list at freeswitch-users-owner@lists.freeswitch.org
When replying, please edit your Subject line so it is more specific than "Re: Contents of FreeSWITCH-users digest..."
Today's Topics:
1. Re: mod_conference kick to abort invitations (Michael Jerris) 2. Re: Handling the 302 Moved Temporarily response from JavaScript (Michael Jerris) 3. Re: No NOTIFY MWI when registering via proxy. (Brian West) 4. Re: remote_media_ip variable not set (Michael Jerris) 5. Re: How to find whether the destination extension supports encryption (Michael Jerris) 6. Re: Bypass_media and re_invite (srinivasula reddy) 7. Re: Handling the 302 Moved Temporarily response from JavaScript (Stephen Crosby) 8. Re: Handling the 302 Moved Temporarily response from JavaScript (Tihomir Culjaga)
--- -------------------------------------------------------------------
Message: 1 Date: Wed, 25 Nov 2009 12:44:46 -0500 From: Michael Jerris <mike@jerris.com> Subject: Re: [Freeswitch-users] mod_conference kick to abort invitations To: freeswitch-users@lists.freeswitch.org Message-ID: <1CCC981C-9F4A-4D97-ACEA-A6DFB906C32B@jerris.com> Content-Type: text/plain; charset="windows-1252"
Its a feature we don't have, patches welcome.
Mike
On Nov 24, 2009, at 5:35 PM, Jan Thiemo Fricke wrote:
Hi members, I?m controlling freeswitch with the conference module via xmlrpc.
Is it desired that the kick command can only kick users that are connected to the conference? Is there no chance abort an invitation? The kick command has no effect until the person I invited with the dial command is connected.
participants (10)
-
Adam Ford
-
Anthony Minessale
-
Brian West
-
Chris Chen
-
Diego Toro
-
Kendall Stauffer
-
Michael Jerris
-
Milena
-
Nandy Dagondon
-
Samuel Mukoti