{Scanned} wanpipe 3.6.0.13 openzap will not compile
Freeswitch Gods, I just bought a B601 Sangoma card. The Wanpipe install went will i get this from a hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=1 : HWEC=64 : V=03 2 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=2 : HWEC=64 : V=03 Card Cnt: B601=1 but when i go to compile the openzap drivers i get the fallowing errors ozmod_wanpipe_la-ozmod_wanpipe.lo -MD -MP -MF .deps/ozmod_wanpipe_la-ozmod_wanpipe.Tpo -c src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c -fPIC -DPIC -o .libs/ozmod_wanpipe_la-ozmod_wanpipe.o cc1: warnings being treated as errors src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c: In function 'wanpipe_open': src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c:493: warning: implicit declaration of function 'sangoma_flush_event_bufs' make: *** [ozmod_wanpipe_la-ozmod_wanpipe.lo] Error 1 I tried to remove the /usr/include/libsangoma.h that still stops on errors. I tried the 3.5 driver branch still the same thing. what i am doing wrong Tom
Is this a fresh git (or svn) checkout of FreeSWITCH? I just did a make current this morning on a system with oz & wanpipe. I used version 3.5.10 from Sangoma's site: http://wiki.sangoma.com/wanpipe-linux-drivers#latest Specifically: ftp://ftp.sangoma.com/linux/current_wanpipe/wanpipe-3.5.10.tgz Uninstall the wanpipe version you have now using the "./Setup uninstall" method and then download & install 3.5.10 and try again. -MC On Mon, Apr 12, 2010 at 12:10 PM, Tom <tomb@cachecomm.com> wrote:
Freeswitch Gods, I just bought a B601 Sangoma card. The Wanpipe install went will i get this from a hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=1 : HWEC=64 : V=03 2 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=2 : HWEC=64 : V=03
Card Cnt: B601=1
but when i go to compile the openzap drivers i get the fallowing errors
ozmod_wanpipe_la-ozmod_wanpipe.lo -MD -MP -MF .deps/ozmod_wanpipe_la-ozmod_wanpipe.Tpo -c src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c -fPIC -DPIC -o .libs/ozmod_wanpipe_la-ozmod_wanpipe.o cc1: warnings being treated as errors src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c: In function 'wanpipe_open': src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c:493: warning: implicit declaration of function 'sangoma_flush_event_bufs' make: *** [ozmod_wanpipe_la-ozmod_wanpipe.lo] Error 1
I tried to remove the /usr/include/libsangoma.h that still stops on errors. I tried the 3.5 driver branch still the same thing. what i am doing wrong
Tom
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Michael Collins wrote:
Is this a fresh git (or svn) checkout of FreeSWITCH? I just did a make current this morning on a system with oz & wanpipe. I used version 3.5.10 from Sangoma's site:
http://wiki.sangoma.com/wanpipe-linux-drivers#latest Specifically: ftp://ftp.sangoma.com/linux/current_wanpipe/wanpipe-3.5.10.tgz
Uninstall the wanpipe version you have now using the "./Setup uninstall" method and then download & install 3.5.10 and try again. -MC
On Mon, Apr 12, 2010 at 12:10 PM, Tom <tomb@cachecomm.com <mailto:tomb@cachecomm.com>> wrote:
Freeswitch Gods, I just bought a B601 Sangoma card. The Wanpipe install went will i get this from a hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=1 : HWEC=64 : V=03 2 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=2 : HWEC=64 : V=03
Card Cnt: B601=1
but when i go to compile the openzap drivers i get the fallowing errors
ozmod_wanpipe_la-ozmod_wanpipe.lo -MD -MP -MF .deps/ozmod_wanpipe_la-ozmod_wanpipe.Tpo -c src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c -fPIC -DPIC -o .libs/ozmod_wanpipe_la-ozmod_wanpipe.o cc1: warnings being treated as errors src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c: In function 'wanpipe_open': src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c:493: warning: implicit declaration of function 'sangoma_flush_event_bufs' make: *** [ozmod_wanpipe_la-ozmod_wanpipe.lo] Error 1
I tried to remove the /usr/include/libsangoma.h that still stops on errors. I tried the 3.5 driver branch still the same thing. what i am doing wrong
Tom
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
------------------------------------------------------------------------
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
MC, i just got off the phone with Sangoma they said the the B601 card will only work with the 3.6 driver. Which will not work with openzap is that right. Thanks Tom
Hi Tom, The B601 will not work with sangoma_prid because the B601 does not have a hardware HDLC framer implemented (which is required by sangoma_prid). If you need a PRI interface, you can still use the B601 and configure the T1/E1 port in "zaptel mode" and use libpri instead. If you need a RBS interface, the B601 will work fine. Regards, *David Yat Sin, **BEng**, **Software Engineer** *Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada t. 1 905 474 1990 x 119 | e. _dyatsin@sangoma.com <mailto:dyatsin@sangoma.com>_ On 4/12/2010 4:26 PM, Tom wrote:
Michael Collins wrote:
Is this a fresh git (or svn) checkout of FreeSWITCH? I just did a make current this morning on a system with oz& wanpipe. I used version 3.5.10 from Sangoma's site:
http://wiki.sangoma.com/wanpipe-linux-drivers#latest Specifically: ftp://ftp.sangoma.com/linux/current_wanpipe/wanpipe-3.5.10.tgz
Uninstall the wanpipe version you have now using the "./Setup uninstall" method and then download& install 3.5.10 and try again. -MC
On Mon, Apr 12, 2010 at 12:10 PM, Tom<tomb@cachecomm.com <mailto:tomb@cachecomm.com>> wrote:
Freeswitch Gods, I just bought a B601 Sangoma card. The Wanpipe install went will i get this from a hwprobe ------------------------------- | Wanpipe Hardware Probe Info | ------------------------------- 1 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=1 : HWEC=64 : V=03 2 . AFT-B601-SH : SLOT=4 : BUS=3 : IRQ=90 : PORT=2 : HWEC=64 : V=03
Card Cnt: B601=1
but when i go to compile the openzap drivers i get the fallowing errors
ozmod_wanpipe_la-ozmod_wanpipe.lo -MD -MP -MF .deps/ozmod_wanpipe_la-ozmod_wanpipe.Tpo -c src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c -fPIC -DPIC -o .libs/ozmod_wanpipe_la-ozmod_wanpipe.o cc1: warnings being treated as errors src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c: In function 'wanpipe_open': src/ozmod/ozmod_wanpipe/ozmod_wanpipe.c:493: warning: implicit declaration of function 'sangoma_flush_event_bufs' make: *** [ozmod_wanpipe_la-ozmod_wanpipe.lo] Error 1
I tried to remove the /usr/include/libsangoma.h that still stops on errors. I tried the 3.5 driver branch still the same thing. what i am doing wrong
Tom
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
------------------------------------------------------------------------
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
MC, i just got off the phone with Sangoma they said the the B601 card will only work with the 3.6 driver. Which will not work with openzap is that right.
Thanks
Tom
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
participants (3)
-
David Yat Sin
-
Michael Collins
-
Tom