Outbound sip address call fails
I am trying to make a test call to the FreeSwitch conference address, sip:888@conference.freeswitch.org on a Bria softphone. However, it fails with a 404 Not found message. I have struggled with this for a while. Is there something special I must do on the Bria to make this happen correctly? Thanks, Lars http://pastebin.freeswitch.org/10715
Sounds like bria is sending the invite via the proxy which is your local FS box and NOT direct. /b On Oct 14, 2009, at 4:26 PM, Lars Zeb wrote:
I am trying to make a test call to the FreeSwitch conference address, sip:888@conference.freeswitch.org on a Bria softphone. However, it fails with a 404 Not found message.
I have struggled with this for a while. Is there something special I must do on the Bria to make this happen correctly?
Thanks, Lars
Brian, Does this mean that Bria should be sending the invite directly to sip:888@conference.freeswitch.org and the From address should be the address of the Bria itself rather than FS? Lars From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Brian West Sent: Wednesday, October 14, 2009 8:55 PM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Outbound sip address call fails Sounds like bria is sending the invite via the proxy which is your local FS box and NOT direct. /b On Oct 14, 2009, at 4:26 PM, Lars Zeb wrote: I am trying to make a test call to the FreeSwitch conference address, sip:888@conference.freeswitch.org on a Bria softphone. However, it fails with a 404 Not found message. I have struggled with this for a while. Is there something special I must do on the Bria to make this happen correctly? Thanks, Lars http://pastebin.freeswitch.org/10715
no clue it depends on how you have it configured. If you have an outbound proxy set it'll send all calls to the proxy. If not then most likely it will go direct to the destination. /b On Oct 15, 2009, at 12:00 AM, Lars Zeb wrote:
Brian,
Does this mean that Bria should be sending the invite directly to sip:888@conference.freeswitch.org and the From address should be the address of the Bria itself rather than FS?
Lars
I don't think I have a proxy. It's pretty standard installation. Name Type Data State ============================================================================ ===================== internal profile sip:mod_sofia@192.168.10.29:5060 RUNNING (0) internal-ipv6 profile sip:mod_sofia@[::1]:5060 RUNNING (0) external profile sip:mod_sofia@192.168.10.29:5090 RUNNING (0) flowroute gateway sip:55555@sip.flowroute.com REGED 192.168.10.29 alias internal ALIASED ============================================================================ ===================== From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Brian West Sent: Thursday, October 15, 2009 6:55 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Outbound sip address call fails no clue it depends on how you have it configured. If you have an outbound proxy set it'll send all calls to the proxy. If not then most likely it will go direct to the destination. /b On Oct 15, 2009, at 12:00 AM, Lars Zeb wrote: Brian, Does this mean that Bria should be sending the invite directly to sip:888@conference.freeswitch.org and the From address should be the address of the Bria itself rather than FS? Lars
Lars Zeb <larclap@yahoo.com> said:
I don't think I have a proxy. It's pretty standard installation.
Is the phone itself configured to use a proxy? -- Russell Mosemann ________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
I don't think Bria is set to use a proxy. In the SIP Account/Account tab, it is set to "Register with domain and receive calls" and "Send outbound via" is set to use Domain rather than "Proxy Address". The Account ID is set to 1009@192.168.10.29, where the IP is the address of FreeSwitch.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users- bounces@lists.freeswitch.org] On Behalf Of Russell.Mosemann@cune.org Sent: Thursday, October 15, 2009 9:48 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Outbound sip address call fails
Lars Zeb <larclap@yahoo.com> said:
I don't think I have a proxy. It's pretty standard installation.
Is the phone itself configured to use a proxy?
-- Russell Mosemann
________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Lars Zeb <larclap@yahoo.com> said:
I don't think Bria is set to use a proxy.
In the SIP Account/Account tab, it is set to "Register with domain and receive calls" and "Send outbound via" is set to use Domain rather than "Proxy Address".
The Account ID is set to 1009@192.168.10.29, where the IP is the address of FreeSwitch.
That's exactly how I have X-Lite configured, and I am able to call the conference directly by entering the conference URL. I'm sitting behind NAT, too. Under the Topology tab, it is set to "Discover global address" and "Discover server" (for STUN). "Enable ICE" is checked. The next thing to check might be if the phone traffic is going directly to the Internet and getting past your firewall. -- Russell Mosemann ________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
Russell, My settings in Bria are just like yours. I captured the SIP trace from the Bria and it says it is using the FreeSwitch as the Outbound Proxy. I am very confused. I tried dial sip:echo@iptel.org. In the pastebin you can see that this address came over to the cli as "echo". Is it Bria which is messing up, or my FS configuration? Where did Bria get the Contact info at lines 79 & 82? 192.168.10.11 is the address of the softphone, so I don't think sip:1009@192.168.10.11 makes sense. http://pastebin.freeswitch.org/10723 Lars
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users- bounces@lists.freeswitch.org] On Behalf Of Russell.Mosemann@cune.org Sent: Thursday, October 15, 2009 10:33 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Outbound sip address call fails
Lars Zeb <larclap@yahoo.com> said:
I don't think Bria is set to use a proxy.
In the SIP Account/Account tab, it is set to "Register with domain and receive calls" and "Send outbound via" is set to use Domain rather than "Proxy Address".
The Account ID is set to 1009@192.168.10.29, where the IP is the address of FreeSwitch.
That's exactly how I have X-Lite configured, and I am able to call the conference directly by entering the conference URL. I'm sitting behind NAT, too. Under the Topology tab, it is set to "Discover global address" and "Discover server" (for STUN). "Enable ICE" is checked. The next thing to check might be if the phone traffic is going directly to the Internet and getting past your firewall.
-- Russell Mosemann
________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Lars Zeb <larclap@yahoo.com> said:
I tried dial sip:echo@iptel.org. In the pastebin you can see that this address came over to the cli as "echo". Is it Bria which is messing up, or my FS configuration?
It looks like a Bria problem. If you open the account information and go to the Advanced tab, is the box checked to "Send outgoing request directly to target"? -- Russell Mosemann ________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
No, the checkbox is unchecked.
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users- bounces@lists.freeswitch.org] On Behalf Of Russell.Mosemann@cune.org Sent: Friday, October 16, 2009 10:30 AM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Outbound sip address call fails
Lars Zeb <larclap@yahoo.com> said:
I tried dial sip:echo@iptel.org. In the pastebin you can see that this address came over to the cli as "echo". Is it Bria which is messing up, or my FS configuration?
It looks like a Bria problem. If you open the account information and go to the Advanced tab, is the box checked to "Send outgoing request directly to target"?
-- Russell Mosemann
________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
Thanks, Russell, that did it. Works perfectly!
-----Original Message----- From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users- bounces@lists.freeswitch.org] On Behalf Of Russell Mosemann Sent: Sunday, October 18, 2009 5:40 PM To: freeswitch-users@lists.freeswitch.org Subject: Re: [Freeswitch-users] Outbound sip address call fails
No, the checkbox is unchecked.
Well, check it.
-- Russell Mosemann
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
participants (4)
-
Brian West
-
Lars Zeb
-
Russell Mosemann
-
Russell.Mosemann＠cune.org