libpri_span vs prispans
Hi all, What difference it will make, if I use pri_span configuration and lib_pri span configuration in openzap.conf.xml. I'm preety much confused on the difference between this.
lakshmanan ganapathy <lakindia89@gmail.com> said:
What difference it will make, if I use pri_span configuration and lib_pri span configuration in openzap.conf.xml. I'm preety much confused on the difference between this.
Openzap can handle a T1/E1 itself, or openzap can use libpri to do that. libpri is more mature than openzap. In my case openzap was not able to handle everything invovling a T1 here, and using libpri fixed it. A libpri_span configuration is handled by libpri. A pri_span configuration is handled natively by openzap. Use the one that works for you. -- Russell Mosemann ________________________________________________________ Concordia University, Nebraska See http://www.cune.edu/ for the latest news and events!
On Fri, Oct 9, 2009 at 5:57 AM, <Russell.Mosemann@cune.org> wrote:
lakshmanan ganapathy <lakindia89@gmail.com> said:
What difference it will make, if I use pri_span configuration and lib_pri span configuration in openzap.conf.xml. I'm preety much confused on the difference between this.
Openzap can handle a T1/E1 itself, or openzap can use libpri to do that. libpri is more mature than openzap. In my case openzap was not able to handle everything invovling a T1 here, and using libpri fixed it.
A libpri_span configuration is handled by libpri. A pri_span configuration is handled natively by openzap. Use the one that works for you.
Right now the libpri stack is more mature than the ozmod_isdn stuff. See the OpenZAP page on the wiki for instructions on how to set up ozmod_libpri. -MC
Where can I found entire configurations for a libpri spans. Right now I've only 4 things in my libpri configuration. They are Switchtype, Node, Contect, Dialplan, which is given as example in wiki. But I think libprispan has more configuration. Where can I find those things? On Fri, Oct 9, 2009 at 11:27 PM, Michael Collins <msc@freeswitch.org> wrote:
On Fri, Oct 9, 2009 at 5:57 AM, <Russell.Mosemann@cune.org> wrote:
lakshmanan ganapathy <lakindia89@gmail.com> said:
What difference it will make, if I use pri_span configuration and lib_pri span configuration in openzap.conf.xml. I'm preety much confused on the difference between this.
Openzap can handle a T1/E1 itself, or openzap can use libpri to do that. libpri is more mature than openzap. In my case openzap was not able to handle everything invovling a T1 here, and using libpri fixed it.
A libpri_span configuration is handled by libpri. A pri_span configuration is handled natively by openzap. Use the one that works for you.
Right now the libpri stack is more mature than the ozmod_isdn stuff. See the OpenZAP page on the wiki for instructions on how to set up ozmod_libpri. -MC
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
From libs/openzap/mod_openzap/mod_openzap.c and libs/openzap/src/ozmod_libpri/ozmod_libpri.c
node=cpe|net switch=ni1|ni2|dms100|lucent5|5ess|att4ess|4ess|euroisdn|gr303eoc|gr303tmc dp=international|national|local|isdn|private|unknown l1=alaw|ulaw <-- this recently is set based on the trunk type, but old openzap in E1 mode needs to explicitly set it to alaw debug=q921_raw,q921_dump,q921_state,config,q931_dump,q931_state,q931_anomaly,apdu,acc none or all opts=suggest_channel,omit_display,omit_redirecting_number The following values are commonly known. context= dialplan= On Sat, Oct 10, 2009 at 12:39 AM, lakshmanan ganapathy <lakindia89@gmail.com
wrote:
Where can I found entire configurations for a libpri spans. Right now I've only 4 things in my libpri configuration. They are Switchtype, Node, Contect, Dialplan, which is given as example in wiki.
But I think libprispan has more configuration. Where can I find those things?
On Fri, Oct 9, 2009 at 11:27 PM, Michael Collins <msc@freeswitch.org>wrote:
On Fri, Oct 9, 2009 at 5:57 AM, <Russell.Mosemann@cune.org> wrote:
lakshmanan ganapathy <lakindia89@gmail.com> said:
What difference it will make, if I use pri_span configuration and lib_pri span configuration in openzap.conf.xml. I'm preety much confused on the difference between this.
Openzap can handle a T1/E1 itself, or openzap can use libpri to do that. libpri is more mature than openzap. In my case openzap was not able to handle everything invovling a T1 here, and using libpri fixed it.
A libpri_span configuration is handled by libpri. A pri_span configuration is handled natively by openzap. Use the one that works for you.
Right now the libpri stack is more mature than the ozmod_isdn stuff. See the OpenZAP page on the wiki for instructions on how to set up ozmod_libpri. -MC
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org
-- Moises Silva Software Developer Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada t. 1 905 474 1990 x 128 | e. moy@sangoma.com
participants (4)
-
lakshmanan ganapathy
-
Michael Collins
-
Moises Silva
-
Russell.Mosemann＠cune.org