Can I start multiple instances of mod-portaudio? I would like to have multiple channels from my alsa-compliant soundcard but I can't find a way to run multiple channels in FreeSWITCH. I am connecting to a PABX and need to bridge calls. Am I missing something obvious? Thank you, Erik

Thanks, I saw that in the wiki and was going to try it next. But after adding autonat:1.2.3.4 looks like last nights test is ok now, I am hoping the problem is fixed. FS would work fine first 4-9 hours then stopped answering incoming. Funny thing, no problem like this with the SPA9000 for 2 years using 2 DSL connections. Thanks again. On 10/12/10 19:28, Anthony Minessale wrote:

Start fs with -nonat

On Oct 12, 2010 7:27 PM, "Mario" <mario_fs@mgtech.com <mailto:mario_fs@mgtech.com>> wrote:

...

I am using ext... autonat:1.2.3.4 in sip internal and external as per wiki. The sofia status is ok for the profiles bu the nat_map shows the wrong address because the router is sending the wrong wan IP in the pnp request. Since I have autonat:1.2.3.4 coded is there a way to force FS not to use uPNP so it does not request nat info from the router? I need it on in the router for other things. Thanks. Mario

_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org <mailto:FreeSWITCH-users@lists.freeswitch.org> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org

_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org

The router (Linksys RV042) has a problem that caused me grief with FS: I use dual wan, 1 static and 1 dynamic DSL. It turned out uPNP only works for the dynamic ip. If I turn off dynamic then uPNP does not allow FS to get the nat info for the static line. But if I have both wans active/on and sip traffic goes out the static uPNP reports the dynamic as the public address! This messes up the ITSP and looks like what caused FS to stop incoming calls after several hours. What drove me nut is: I did not think this was involved because my Linksys SPA9000/400 SIP PBX has no trouble with the same dual wan setup. Thanks a lot for answering but until I figure out how to dual wan FS or replace the RV042 with something better the autonat:1.2.3.4 looks like it fixed the problem, need more hours to test. Thanks again. Mario On 10/13/2010 08:38 AM, Rupa Schomaker wrote:

Mario,

Does your router have the ability to show current NAT mappings that are setup via UPNP? If so, can you verify that it's (router's) table matches the mappings that FS thinks are setup (nat_map status)? Freeswitch is supposed to periodically refresh the nat mappings but maybe there is some weird issue with your particular router.

There are also some test programs in libs/miniupnpc which can query your router's UPNP table if the router itself can't show it.

On Wed, Oct 13, 2010 at 9:17 AM, Mario <mario_fs@mgtech.com <mailto:mario_fs@mgtech.com>> wrote:

Thanks, I saw that in the wiki and was going to try it next. But after adding autonat:1.2.3.4 looks like last nights test is ok now, I am hoping the problem is fixed. FS would work fine first 4-9 hours then stopped answering incoming. Funny thing, no problem like this with the SPA9000 for 2 years using 2 DSL connections. Thanks again.

-- -Rupa

_______________________________________________ FreeSWITCH-users mailing list FreeSWITCH-users@lists.freeswitch.org http://lists.freeswitch.org/mailman/listinfo/freeswitch-users UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users http://www.freeswitch.org

-- *Mario*