On Mon, Jun 21, 2010 at 9:51 AM, Neil Patel <neilp@cs.stanford.edu> wrote:

Hi Moises,

I recently added a second PRI line to my A102 and followed your instructions below (modified /etc/wanpipe/smg_pri.conf; openzap.conf as shown below) and can successfully dial out with g1, but not the recently added second line set on g2. Below is the error we get:

freeswitch@otalo> originate openzap/smg_prid/a/<num>@g2 &echo
2010-06-21 19:15:59.591930 [WARNING] ozmod_sangoma_boost.c:344 TX EVENT: CALL_START:(80) [w1g1] CSid=3 Seq=4 Cn=[N/A] Cd=[9586550654] Ci=[N/A] Rdnis=[]
2010-06-21 19:15:59.624992 [WARNING] ozmod_sangoma_boost.c:1632 RX EVENT (N): CALL_START_ACK:(81) [w2g1] Rc=0 CSid=3 Seq=6
2010-06-21 19:15:59.625987 [NOTICE] switch_channel.c:675 New Channel OpenZAP/1:31/<num>@g2 [19ae26fb-f9e4-480a-9cc7-11fa91b8bb1c]
2010-06-21 19:15:59.724996 [WARNING] ozmod_sangoma_boost.c:1632 RX EVENT (N): CALL_STOPPED:(85) [w2g1] Rc=3 CSid=3 Seq=7
2010-06-21 19:15:59.724996 [NOTICE] mod_openzap.c:1935 Hangup OpenZAP/1:31/<num>@g2 [CS_CONSUME_MEDIA] [NO_ROUTE_DESTINATION]

-ERR NO_ROUTE_DESTINATION

Seems like a config issue, but not sure what I'm missing. Any ideas?

Thanks in advance,
Neil

On Sun, May 16, 2010 at 10:50 AM, Moises Silva <moises.silva@gmail.com> wrote:

Hi Again Neil,

I just noticed your dial string is incorrect. The correct syntax is:

OpenZAP//<chan_code>/[number]

The span and chan code are mandatory. The number is optional ( FXS channels do not require a number, they just ring the FXO device connected to them).

The span is either a number ( span id, the id is a number assigned in the order in which the span is defined in openzap.conf ) or a span name also as specified in the [span wanpipe <span_name>] line in openzap.conf

The chan code is either a number ( for spans that support individual channel selection, boost is NOT one of them ), or a channel hunting mode, there is currently 2 modes, "a" is top down and "A" is bottom up.

So, this is a valid string for you case:

OpenZAP/smg_prid/a/<number>

In the specific case of boost in socket mode ( openzap only supports socket mode ) the number may contain @gX where X is a group ( for hunting as configured in /etc/wanpipe/smg_pri.conf). Boost signaling are a special case because the hunting for channels is not done within FreeSWITCH but in sangoma_prid binary ( in the new OpenZAP version called FreeTDM this has changed depending on configuration).

Bottom line, this should work:

OpenZAP/smg_prid/a/1234@g1

If you have g1 configured in /etc/wanpipe/smg_pri.conf

Moises Silva
Senior Software Engineer
Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada
t. 1 905 474 1990 x 128 | e. moy@sangoma.com

On Sat, May 15, 2010 at 6:26 PM, Neil Patel <neilp@cs.stanford.edu> wrote:

Span was originally in the boost section when I got this error, so I thought I'd try it in analog and both. None work.

-Neil

On Sat, May 15, 2010 at 3:18 PM, Moises Silva <moises.silva@gmail.com> wrote:

Why do you have 2 spans in openzap.conf.xml with the same name, in both the boost and analog sections?
Moises Silva
Senior Software Engineer
Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3 Canada
t. 1 905 474 1990 x 128 | e. moy@sangoma.com

On Sat, May 15, 2010 at 3:52 PM, Neil Patel <neilp@cs.stanford.edu> wrote:

Hi All,

I am trying to dial out over my PRI, and am getting this error:

2010-05-16 01:01:21.452392 [CRIT] zap_io.c:1139 SPAN NOT DEFINED!
2010-05-16 01:01:21.452392 [ERR] mod_openzap.c:1154 No channels available

2010-05-16 01:01:21.452392 [ERR] switch_ivr_originate.c:2249 Cannot create outgoing channel of type [OpenZAP] cause: [NORMAL_CIRCUIT_CONGESTION]

This is my openzap.conf:

[span wanpipe smg_prid]
name => smg_prid
trunk_type =>e1

b-channel => 1:1-15
b-channel => 1:17-31
trunk_type =>e1
b-channel => 2:1-15
b-channel => 2:17-31

This is my openzap.conf.xml:
<configuration name="openzap.conf" description="OpenZAP Configuration">

 <settings>
 <param name="debug" value="0"/>

 </settings>
 <boost_spans>

 
 <param name="dialplan" value="XML"/>
 <param name="context" value="default"/>

 
 </boost_spans>

 <analog_spans>
 

 <param name="dialplan" value="XML"/>
 <param name="context" value="default"/>


 
 </analog_spans>
</configuration>

And here is the lua code I'm using to dial out:

sessiondata = "OpenZAP/smg_prid/<num>"
new_session = freeswitch.Session(sessiondata)

What am I missing here?
Thanks,
Neil

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org