David ,

 

Thank you for such prompt response!

 

I checked my X-Lite configuration and find that “Use rport” had been checked.

However, Registration doesn’t include anything about fs_nat(see below). Do I need explicitly configure/load RTP proxy support? If yes, will appreciate instructions.

 

Regards

Stas

Registrations:

=================================================================================================

Call-ID:        NTBjOWYyMTM4ZGFlYzFmZjQyZDkwZGZhZmUyODc5NGY.

User:           1005@174.123.63.250

Contact:        "Test User" <sip:1005@24.130.59.97:22150;rinstance=b125d2389d25349c>

Agent:          X-Lite release 1104o stamp 56125

Status:         Registered(UDP)(unknown) EXP(2010-09-01 08:33:35)

Host:           hostname10178.theplanet.host

IP:             24.130.59.97

Port:           22150

Auth-User:      1005

Auth-Realm:     174.123.63.250

MWI-Account:    1005@174.123.63.250

 

=================================================================================================

 

From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of David Ponzone
Sent: Wednesday, September 01, 2010 2:42 AM
To: FreeSWITCH Users Help
Subject: Re: [Freeswitch-users] 2 endpoints behing NATs

 

Stas,

 

FS includes a RTP Proxy with server-side NAT-traversal capabilities.

So this should work if you register your phones to the internal dialplan, which you probably do.

 

In the Sip Account/Advanced tab settings of X-lite, you have to check "Use rport".

 

After that, you can check on FS if the NAT was detected:

 

sofia status profile internal

 

You should see your 2 phones connected, each of them with a Contact line.

If this Contact line does not include "fs_nat=yes", then the NAT was not detected, which will probably happen if "Use rport" is missing.

 

That's a first step.

 

David Ponzone  Direction Technique

tel:      01 74 03 18 97

gsm:   06 66 98 76 34

 

Service Client IPeva

tel:      0811 46 26 26

 

Ce message et toutes les pièces jointes sont confidentiels et établis à l'intention exclusive de ses destinataires. Toute utilisation ou diffusion non autorisée est interdite. Tout message électronique est susceptible d'altération. IPeva décline toute responsabilité au titre de ce message s'il a été altéré, déformé ou falsifié. Si vous n'êtes pas destinataire de ce message, merci de le détruire immédiatement et d'avertir l'expéditeur.

 

 

 

 

Le 01/09/2010 à 11:25, Stas Khirman a écrit :



Hi,

 

Sorry for novice question:

 

Successfully setup FreeSWITCH on publicly accessible IP using 1.0.6 standard configuration. No changes in configuration, dial plan, etc…

 

Basic tests (music,echo,etc) are working ok. However, the problem observed with call between two softphones (X-lite) behind NATs – call signal are coming through but no media. Both NATs are kind of typical household WiFi routers.   Everything ok if one of softphones is connected without NAT.

 

Does two NATs configuration supported by stock FreeSWITCH ? Can I make it work by changing some configuration parameters or I need something like RTP proxy or similar?

 

Regards

Stas

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org