Thanks Jerry, for making the wancfg_fs configuration available.

On Wed, Jan 13, 2010 at 9:45 PM, Jerry Richards <jerry.richards@teotech.com> wrote:
Here are my instructions to install the wanpipe driver and I have not had your problem:
 

1)       Download the following Wanpipe driver tarball wanpipe-<version>.tgz

2)       Store the wanpipe-<version>.tgz file in the /opt folder.

3)       tar xvfz wanpipe-<version>.tgz

4)       cd wanpipe-<version>

5)       make openzap

6)       make install

7)       make install_pri

8)       wanrouter hwprobe     // confirms successful wanpipe installation

9)       /usr/sbin/wancfg_fs   // starts wanpipe configuration utility

10)   1=NO            // Change Freeswitch Configuration Directory

11)   1=T1            // Select Media Type

12)   1=YES (keep)    // Configure Port 1 T1, B8ZS, ESF

13)   1=NORMAL        // Select Clock

14)   1=NATIONAL      // Select Switchtype

15)   1=CPE           // Select Signaling Type

16)   1               // Input Group #

17)   1=YES           // Enable H/W DTMF Detect

18)   1=YES           // Enable FAX Detect

19)   1=YES=CONTINUE  // Configuration Complete

20)   1=YES           // Save Configuration

21)   1=YES           // Wanrouter start on reboot

22)   1=YES           // smg_ctrl start/stop on wanrouter start

23)   Done.

 
Jerry

From: Magesh R [mailto:magesh.freeswitch@gmail.com]
Sent: Tuesday, January 12, 2010 8:21 PM
To: freeswitch-users@lists.freeswitch.org
Subject: [Freeswitch-users] Sangoma PRI installation for FreeSWITCH

Dear All,
         I have installed Sangoma PRI card in machine with following steps,
                 * wget ftp://ftp.sangoma.com/linux/custom/3.5/wanpipe-3.5.8.7.tgz
                 * tar -xvfz wanpipe-3.5.8.7.tgz
                 * cd wanpipe-3.5.8.7
                 * make openzap
                 * make install
                 * make install_pri
     
           I have executed "wanrouter hwprobe" command it prints the following details,
   
           1 . AFT-A102-SH : SLOT=4 : BUS=3 : IRQ=11 : CPU=A : PORT=1 : HWEC=0 : V=36
           2 . AFT-A102-SH : SLOT=4 : BUS=3 : IRQ=11 : CPU=A : PORT=2 : HWEC=0 : V=36
       
        Card Cnt: A101-2=1

       Next I have executed wancfg_fs script to configure the sangoma for freeswitch.
It creates the following configuration files
                     * wanpipe1.conf
                     * wanpipe2.conf
                     * smg_prid.conf
                     * openzap.conf
                     * openzap.conf.xml
       I have attached those files.
       I have started the wanrouter and printed the wanrouter status,
              Wanrouter Status:

Device name | Protocol | Station | Status        |
wanpipe1    | AFT TE1  | N/A     | Connected     |
wanpipe2    | AFT TE1  | N/A     | Disconnected  |


      Next I have started the smg_ctrl, but it failed to start. It prints the following things,
smg_ctrl start

Starting processes...
Loading SCTP...OK
Starting sangoma_prid...OK
sangoma_prid failed to start
check /var/log/sangoma_mgd.log for errors

Stopping running processes...
safe_sangoma not running...
sangoma_prid is stopped
Removing PID files...done

I have checked /var/log/sangoma_mgd.log file. But nothing was there.

Could any please tell me where I made mistake?

Thanks,
Mag


             


_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org