On Thu, Jul 7, 2011 at 8:37 AM, John <
freeswitch@earthspike.net> wrote:
> On 06/07/11 13:53, shouldbe q931 wrote:
>> On Fri, Jun 17, 2011 at 7:43 PM, shouldbe q931<
shouldbeq931@gmail.com> wrote:
>>> On Fri, Jun 17, 2011 at 7:08 PM, John<
freeswitch@earthspike.net> wrote:
>>>> Mike, Shouldbe,
>>>>
>>>> We now have CLIP on the line for sure, and I ordered COLP at the same time
>>>> and am assured that that has been turned on as well, but I still cannot get
>>>> outgoing CLI to work properly. Mike, you mention setting the TON to
>>>> 'national'; where is that setting?
>>>>
>>>> At the moment, my dialplan looks like
http://pastebin.freeswitch.org/16548
>>>> with . An outgoing call gives the log 7 at
>>>>
http://pastebin.freeswitch.org/16549 (numbers have been changed to protect
>>>> the innocent!) but the number that 01234 567890 sees on their Caller ID is
>>>> not 876543 but the main number of the line (876540, say). I have tried
>>>> setting the outgoing_caller_id_number to 6, 10 and 11 digits, restarting FS
>>>> after each change, but with no success.
>>>>
>>>> The service provider has only one clue to offer: "With regards to the
>>>> configuration at the exchange, the line is set to 6 digits to switch." which
>>>> makes eminent sense, and suggests that I should be presenting 6 digits.
>>>> Incoming calls have a 6 digit called number and 10 digit calling number.
>>>>
>>>> Thanks for the help so far. Any other ideas?
>>>>
>>>> John
>>>>
>>>>
>>> I don't have any experience with FS connecting over ISDN so can't help
>>> you much further on the FS configuration:-(
>>>
>>> However on the lines, I would be very tempted to see if you can borrow
>>> a BRI tester, or what I've frequently used in the past is an
>>> Eicon/Dialogic card as the test functions (under windows) are nearly
>>> as good, that might help you see if it _is_ a BT problem, or a FS
>>> configuration issue. It would need a 2k/XP machine, but something like
>>>
http://cgi.ebay.co.uk/EICON-DIVA-2-01-PCI-GRAPHICS-CARD-/270761571564
>>> is what I have used in the past. I think I might have one of the
>>> PCMCIA ones somewhere, but I'd need to test it still works
>>>
>>> I'm fairly sure that the "6 digits to switch" is what they are sending
>>> to you, not what they are expecting from you. I can't access out
>>> remaining BRI (Avaya) PBX from here, but on our PRI (again Avaya)
>>> switches, we are sending 10 digits.
>>>
>>> Cheers
>>>
>> Apologies for the very long delay...
>>
>> On our PRI systems we are sending 10 digits (2071231234), and on the
>> BRI system we are sending 11 digits (02071231234).
>>
>> Cheers
> Thanks. I have tried all of these digit options, along with setting the
> TON and NPI, so I am now working through every possible option and tweak
> with the supplier (including including codes to remove/reapply CPS). I
> am trying to avoid booking this as a fault, until I am sure I won't be
> charged for a 'no fault found' but it is beginning to look unavoidable.
> I am certainly building enough information for a good wiki page on this
> when I finally get it cracked! Incidentally, the Sangoma 'wanpipemon'
> provides a useful PCAP mode which delivers the entire D-channel as a
> wireshark PCAP file, so I am able to debug the Q.931 signalling down to
> bit level.
>
> John
>