here is the dump message for the port :

freeswitch@internal> ftdm dump 1 4
span_id: 1
chan_id: 4
physical_span_id: 1
physical_chan_id: 4
physical_status: ok
physical_status_red: 0
physical_status_yellow: 0
physical_status_rai: 0
physical_status_blue: 0
physical_status_ais: 0
physical_status_general: 0
signaling_status: UP
type: FXO
state: DOWN
last_state: BUSY
txgain: 0.00
rxgain: 0.00
cid_date:
cid_name:
cid_num:
ani:
aniII:
dnis:
rdnis:
cause: NONE
session: (none)

-- States --                   -- Function --                 -- Location --                 -- Time Offset --
PROGRESS => PROGRESS_MEDIA     [channel_receive_message_fxo]  [mod_freetdm.c:1040]           0ms
PROGRESS_MEDIA => UP           [channel_receive_message_fxo]  [mod_freetdm.c:1040]           0ms
UP    => HANGUP                [channel_on_hangup]            [mod_freetdm.c:586]            11641ms
HANGUP => DOWN                 [ftdm_analog_channel_run]      [ftmod_analog.c:564]           519ms
DOWN  => DIALING               [analog_fxo_outgoing_call]     [ftmod_analog.c:62]            182116ms
DIALING => BUSY                [ftdm_analog_channel_run]      [ftmod_analog.c:505]           5020ms
BUSY  => DOWN                  [ftdm_analog_channel_run]      [ftmod_analog.c:802]           20ms
DOWN  => DIALING               [analog_fxo_outgoing_call]     [ftmod_analog.c:62]            29140ms
DIALING => BUSY                [ftdm_analog_channel_run]      [ftmod_analog.c:505]           5020ms
BUSY  => DOWN                  [ftdm_analog_channel_run]      [ftmod_analog.c:802]           20ms

Time since last state change: 64974617ms

This is for Indonesia line, but it usually works fine using us tone.



On 10/01/2012 11:38 PM, Michael Collins wrote:
Look at line 107 of your paste:
2012-10-01 11:08:24.301591 [DEBUG] switch_ivr_originate.c:3508 Originate Resulted in Error Cause: 34 [NORMAL_CIRCUIT_CONGESTION]

For whatever reason mod_freetdm thinks that port is in use. Try "ftdm dump <span> <chan>" to see if there's any clues as to the state of the channel. Also, what country is this? Do you have your tones properly specified?
-MC

On Mon, Oct 1, 2012 at 12:30 AM, William Alianto <william@xofap.com> wrote:
I recently installed 2 spans of analog cards to my box. After all the
configuration, I can already accept incoming from the FXO ports. But
when I tried to do outbound call, it always fail. This is the dialplan I
used for outgoing call

<extension name="freetdm" >
    <condition field="destination_number" expression="^9(\d+)$" >
        <action application="set" data="call_direction=outbound" />
        <action application="set" data="hangup_after_bridge=true" />
        <action application="bridge" data="freetdm/FXO1/4/$1" />
    </condition>
</extension>

And here is the log of the call

http://pastebin.com/PAY42vTh

It seems that the dtmf was not delivered properly. Can anyone help me
with this?

_________________________________________________________________________
Professional FreeSWITCH Consulting Services:
consulting@freeswitch.org
http://www.freeswitchsolutions.com

FreeSWITCH-powered IP PBX: The CudaTel Communication Server
http://www.cudatel.com

Official FreeSWITCH Sites
http://www.freeswitch.org
http://wiki.freeswitch.org
http://www.cluecon.com

FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org



--
Michael S Collins
Twitter: @mercutioviz
http://www.FreeSWITCH.org
http://www.ClueCon.com
http://www.OSTAG.org