Hi Deon

 

Did you encounter any problems when editing the dialplan?

 

I’m not 100% sure, but it would appear that whenever I try and edit default.xml dialplan, the SMG changes status to ‘down’ in the webgui.  I then change it straight back again and it comes back up briefly.

However, I’ve got to the point now where I can’t seem to get the SMG to work again, the TDM drivers start fine, but the SMG just does not want to start.

I have also check the sangomagw log file in /usr/local/smg/log/ but this seems to stop logging anything once the SMG goes down.

 

Do you know of any other log files I could check?

 

Also, if I were to re-install the SMG, would re-running the make/install commands just re-install over the top?  As a newbie to linux I am still not sure if this is the case! J

 

Thanks for your help.

 

Regards

 

Ben

 

From: freeswitch-users-bounces@lists.freeswitch.org [mailto:freeswitch-users-bounces@lists.freeswitch.org] On Behalf Of Deon Vermeulen
Sent: 18 August 2011 07:48
To: FreeSWITCH Users Help
Subject: Re: [Freeswitch-users] Sangoma Media Gateway

 

Hi Ben

 

I do it as follows.

 

Go to File Editor -> dialplan -> default.xml

 

Look for  <extension name="to-sip">

 

At the very end of the extension there is a part that already shows you how to route to IP.

 

                                    <!-- uncomment this if you want to dial to a fixed IP addr -->

                                    <!-- <action application="bridge" data="sofia/internal/${destnumber}@192.168.1.1"/> -->

 

 

So you could have something like this.

 

                                    <action application="set" data="sip_contact_user_replacement=${destnumber}"/>                                   

                                    <action application="set" data="hangup_after_bridge=yes"/>

                                    <action application="bridge" data="sofia/internal/${destnumber}@192.168.1.1"/>

                                    <action application="hangup" data="${originate_disposition}"/>

                       

If you need to setup a DID then you could do something like this.

 

            <extension name="to-switchboard" >

                          <condition field="destination_number" expression="xxxxxxxx">  ( REPLACE xxxxxx with the number dialled on the PSTN)

                                    <action application="set" data="span=${sip_h_X-FreeTDM-SpanName}"/>

                                    <action application="log" data="INFO Incoming CALL for switchboard on span=${span}"/>

                                    <action application="set" data="hangup_after_bridge=yes"/>

                                    <action application="bridge" data="sofia/internal/yyyyyyyyy@192.168.1.1"/>   (REPLACE yyyyyy with the destination number of the SIP Phone this call needs to go to)

                                    <action application="hangup" data="${originate_disposition}"/>

                          </condition>

            </extension>

 

 

If your calls need to be routed through the WAN to branch locations etc and you don't want to use the default ulaw/alaw then you could force the codec on the B-Leg of the call to what ever codec you prefer. This will depend on what codecs is supported on the end devices as well as if your card supports transcoding.

 

It could look something like this:

 

            <extension name="to-switchboard" >

                           <condition field="destination_number" expression="xxxxxxxx">            

                                    <action application="set" data="span=${sip_h_X-FreeTDM-SpanName}"/>

                                    <action application="log" data="INFO Incoming CALL for switchboard on span=${span}"/>

                                    <action application="set" data="hangup_after_bridge=yes"/>

                                    <action application="bridge" data="sofia/internal/yyyyyyyyy@192.168.1.1"/>

                                    <action application="hangup" data="{absolute_codec_string=GSM} ${originate_disposition}"/>

                                    <action application="hangup" data="${originate_disposition}"/>

                           </condition>

            </extension>

 

 

These are just simple examples you can use.

 

Hope this is helpful.

 

 

Regards

Deon

 

 

On Aug 17, 2011, at 5:32 PM, Ben Naylor wrote:



Hello

 

Apologies if this is in the wrong place, I am a complete beginner at Freeswitch!

 

Has anyone had much joy with using the above to route calls from ISDN to a SIP provider?  I have setup the SMG which is a stripped down version of Freeswitch, but am struggling to work out what to configure to get this working.

So far I have tried to set up an external gateway to my provider, but this hasn’t appeared in the SMG Web-gui as a SIP profile.  My provider doesn’t required auth by the way, they have just given me an IP to connect to.

 

Any help is greatly appreciated

 

Kind regards

 

Ben

 


FreeSWITCH-users mailing list
FreeSWITCH-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

 

No virus found in this message.
Checked by AVG - www.avg.com
Version: 10.0.1392 / Virus Database: 1520/3840 - Release Date: 08/17/11