New subject: [Freeswitch-users] Not able to make an outgoing Call through FXO....

10 Jan 2008

      I am from India. The Indian dial tone is a combination of 350 Hz tone and a
440 Hz tone. Anyways here is the snippet of my tones.conf @ /etc/openzap/

[us]
generate-dial => v=-7;%(1000,0,350,440)
detect-dial => 350,440

generate-ring => v=-7;%(2000,4000,440,480)
detect-ring => 440,480

generate-busy => v=-7;%(500,500,480,620)
detect-busy => 480,620

generate-attn => v=0;%(100,100,1400,2060,2450,2600)
detect-attn => 1400,2060,2450,2600

generate-callwaiting-sas => v=0;%(300,0,440)
detect-callwaiting-sas => 440

generate-callwaiting-cas => v=0;%(80,0,2750,2130)
detect-callwaiting-cas => 2750,2130

detect-fail1 => 913.8
detect-fail2 => 1370.6
detect-fail3 => 776.7

BR,
Irshad.

On Jan 10, 2008 6:57 AM, Michael Jerris <mike@jerris.com> wrote:
...
Yes, these are set in tones.conf.  You will need to add the correct values
for your area (we can add them to the default config if you can provide
those).  Also, please update to the current code, tony just added quite a
few features to mod_openzap including support for hold music, transfer
(blind and attended), and 3-way.
Mike
On Jan 9, 2008, at 7:57 AM, Irshad Ahamed wrote:
With the same set-up, Outgoing calls are working fine with Asterisk.
Are there any tools to detect the presence of dial tone??? If it's any
parameter issue, can we adjust those parameters???
NOTE: I copied tones.conf available from the source code to /etc/openzap/
BR,
Irshad.
On Jan 5, 2008 12:00 AM, Anthony Minessale <anthmct@yahoo.com > wrote:
...
I think it's waiting for a dialtone before it sends the digits
and then giving up because it can't fine one.
Anthony Minessale II
FreeSWITCH http://www.freeswitch.org/
ClueCon http://www.cluecon.com/
AIM: anthm
MSN:anthony_minessale@hotmail.com
GTALK/JABBER/PAYPAL:anthony.minessale@gmail.com
IRC: irc.freenode.net #freeswitch
FreeSWITCH Developer Conference
sip:888@conference.freeswitch.org
iax:guest@conference.freeswitch.org/888
googletalk:conf+888@conference.freeswitch.org
pstn:213-799-1400
----- Original Message ----
From: Irshad Ahamed < irshad.fswitch@gmail.com>
To: freeswitch-users@lists.freeswitch.org;
freeswitch-dev@lists.freeswitch.org
Sent: Friday, January 4, 2008 4:24:07 AM
Subject: Re: [Freeswitch-users] Not able to make an outgoing Call
through FXO....
Hi Anthony,
Thanks for the info. By adding the span-ID = 2 , I was able to receive
an incoming call successfully.
The dialplan/default.xml is as below:
  <extension name="incoming">
    <condition field="destination_number" expression="^(1)$">
      <action application="bridge" data="openzap/1/1"/>
      <!--action application="bridge" data="openzap/1/1"/>-->
    </condition>
  </extension>
<extension name="outgoing-fxo">
    <condition field="destination_number" expression="^(43)$">
      <action application="bridge" data="openzap/2/1/43"/>
    </condition>
  </extension>
The Openzap.conf.xml looks like below:
<configuration name="openzap.conf" description="OpenZAP Configuration">
  <settings>
    <param name="debug" value="9"/>
  </settings>
  <analog_spans>
    <span id="1">
      <param name="tonegroup" value="us"/>
      <param name="digit-timeout" value="2000"/>
      <param name="max-digits" value="11"/>
      <param name="dialplan" value="XML"/>
      <param name="context" value="default"/>
      <!-- regex to stop dialing when it matches -->
      <!--<param name="dial-regex" value="5555"/>-->
      <!-- regex to stop dialing when it does not match -->
      <!--<param name="fail-dial-regex" value="^5"/>-->
    </span>
    <span id="2">
      <param name="tonegroup" value="us"/>
      <param name="digit-timeout" value="2000"/>
      <param name="max-digits" value="1"/>
      <param name="dialplan" value="XML"/>
      <param name="context" value="default"/>
      <!-- regex to stop dialing when it matches -->
      <!--<param name="dial-regex" value="5555"/>-->
      <!-- regex to stop dialing when it does not match -->
      <!--<param name="fail-dial-regex" value="^5"/>-->
    </span>
  </analog_spans>
</configuration>
But still I am unable to make an Outgoing Call. Please have a look at
the Freeswitch Log below:
2008-01-04 15:45:03 [DEBUG] zap_analog.c:664 process_event() EVENT
[OFFHOOK][1:1] STATE [DOWN]
2008-01-04 15:45:03 [DEBUG] zap_analog.c:726 process_event() Changing
state on 1:1 from DOWN to DIALTONE
2008-01-04 15:45:03 [DEBUG] zap_analog.c:184 zap_analog_channel_run()
ANALOG CHANNEL thread starting.
2008-01-04 15:45:03 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for DIALTONE
2008-01-04 15:45:07 [DEBUG] zap_analog.c:490 zap_analog_channel_run()
DTMF 4
2008-01-04 15:45:07 [DEBUG] zap_analog.c:492 zap_analog_channel_run()
Changing state on 1:1 from DIALTONE to COLLECT
2008-01-04 15:45:07 [DEBUG] mod_openzap.c:968 on_fxs_signal() got FXS
sig [COLLECTED_DIGIT]
2008-01-04 15:45:07 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for COLLECT
2008-01-04 15:45:07 [DEBUG] zap_analog.c:490 zap_analog_channel_run()
DTMF 2
2008-01-04 15:45:07 [DEBUG] mod_openzap.c:968 on_fxs_signal() got FXS
sig [COLLECTED_DIGIT]
2008-01-04 15:45:09 [DEBUG] zap_analog.c:507 zap_analog_channel_run()
Number obtained [42]
2008-01-04 15:45:09 [DEBUG] zap_analog.c:508 zap_analog_channel_run()
Changing state on 1:1 from COLLECT to IDLE
2008-01-04 15:45:09 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for IDLE
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:968 on_fxs_signal() got FXS
sig [START]
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:231 tech_init() Set codec PCMU
20ms
2008-01-04 15:45:09 [NOTICE] switch_channel.c:392
switch_channel_set_name() New Chan OpenZAP/42
[8d46eb7f-4305-49e8-a4a5-eb97af3b696b]
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:892 zap_channel_from_event()
OpenZAP/42 State Change CS_NEW -> CS_INIT
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OpenZAP/42 [BREAK]
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:397
switch_core_session_run() (OpenZAP/42) State INIT
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:256 channel_on_init()
OpenZAP/42 State Change CS_INIT -> CS_RING
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OpenZAP/42 [BREAK]
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:400
switch_core_session_run() (OpenZAP/42) State RING
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:276 channel_on_ring()
OpenZAP/42 CHANNEL RING
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:64
switch_core_standard_on_ring() Standard RING OpenZAP/42
2008-01-04 15:45:09 [INFO] mod_dialplan_xml.c:217 dialplan_hunt()
Processing OpenZAP->42!
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:106 parse_exten() test
conditions ${numbering_plan}() =~ //
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:106 parse_exten() test
conditions destination_number(42) =~ /^(1)$/
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:108 parse_exten() Regex
mismatch
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:106 parse_exten() test
conditions destination_number(42) =~ /^(43)$/
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:108 parse_exten() Regex
mismatch
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:106 parse_exten() test
conditions destination_number(42) =~ /^(42)$/
2008-01-04 15:45:09 [DEBUG] mod_dialplan_xml.c:273 dialplan_hunt()
OpenZAP/42 State Change CS_RING -> CS_EXECUTE
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OpenZAP/42 [BREAK]
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:406
switch_core_session_run() (OpenZAP/42) State EXECUTE
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:294 channel_on_execute()
OpenZAP/42 CHANNEL EXECUTE
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:121
switch_core_standard_on_execute() Standard EXECUTE
2008-01-04 15:45:09 [NOTICE] switch_core_state_machine.c:134
switch_core_standard_on_execute() Execute
set(use_profile=${cond(${is_lan_addr(${network_addr})} == yes ? nat :
default)})
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:158
switch_core_standard_on_execute() Expanded String set(use_profile=default)
2008-01-04 15:45:09 [DEBUG] mod_dptools.c:419 set_function() SET
[use_profile]=[default]
2008-01-04 15:45:09 [NOTICE] switch_core_state_machine.c:134
switch_core_standard_on_execute() Execute set_user(default@${domain})
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:158
switch_core_standard_on_execute() Expanded String set_user(
default@192.168.2.51)
2008-01-04 15:45:09 [NOTICE] switch_core_state_machine.c:134
switch_core_standard_on_execute() Execute info()
2008-01-04 15:45:09 [CRIT] mod_dptools.c:630 info_function()
CHANNEL_DATA:
Channel-State: CS_EXECUTE
Channel-State-Number: 4
Channel-Name: OpenZAP/42
Unique-ID: 8d46eb7f-4305-49e8-a4a5-eb97af3b696b
Channel-Read-Codec-Name: PCMU
Channel-Read-Codec-Rate: 8000
Channel-Write-Codec-Name: PCMU
Channel-Write-Codec-Rate: 8000
Caller-Username: OpenZAP
Caller-Dialplan: XML
Caller-Caller-ID-Name: OpenZAP
Caller-Caller-ID-Number: 1
Caller-Destination-Number: 42
Caller-Unique-ID: 8d46eb7f-4305-49e8-a4a5-eb97af3b696b
Caller-Source: mod_openzap
Caller-Context: default
Caller-Channel-Name: OpenZAP/42
Caller-Channel-Created-Time: 1199441709953187
Caller-Channel-Answered-Time: 0
Caller-Channel-Hangup-Time: 0
Caller-Channel-Transfer-Time: 0
Caller-Screen-Bit: yes
Caller-Privacy-Hide-Name: no
Caller-Privacy-Hide-Number: no
variable_use_profile: default
variable_numbering_plan: US
variable_user_name: default
variable_domain_name: 192.168.2.51
2008-01-04 15:45:09 [NOTICE] switch_core_state_machine.c:134
switch_core_standard_on_execute() Execute answer()
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:663
channel_receive_message_fxs() Changing state on 1:1 from IDLE to UP
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:339
switch_core_session_receive_message() Kill OpenZAP/42 [BREAK]
2008-01-04 15:45:09 [NOTICE] mod_dptools.c:361 answer_function() Channel
[OpenZAP/42] has been answered
2008-01-04 15:45:09 [NOTICE] switch_core_state_machine.c:134
switch_core_standard_on_execute() Execute bridge(openzap/2/1/42)2008-01-04
15:45:09 [DEBUG] mod_openzap.c:231 tech_init() Set codec PCMU 20ms
2008-01-04 15:45:09 [NOTICE] switch_channel.c:392
switch_channel_set_name() New Chan OPENZAP/42
[bef803ed-e932-4a22-84e7-9131070fe771]
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:802 channel_outgoing_channel()
OPENZAP/42 State Change CS_NEW -> CS_INIT
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OPENZAP/42 [BREAK]
2008-01-04 15:45:09 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for UP
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:968 on_fxs_signal() got FXS
sig [UP]
2008-01-04 15:45:09 [DEBUG] zap_analog.c:55 analog_fxo_outgoing_call()
Changing state on 2:1 from DOWN to DIALING
2008-01-04 15:45:09 [DEBUG] zap_analog.c:184 zap_analog_channel_run()
ANALOG CHANNEL thread starting.
2008-01-04 15:45:09 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 2:1 for DIALING
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:397
switch_core_session_run() (OPENZAP/42) State INIT
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:256 channel_on_init()
OPENZAP/42 State Change CS_INIT -> CS_RING
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OPENZAP/42 [BREAK]
2008-01-04 15:45:09 [DEBUG] switch_ivr_originate.c:625
switch_ivr_originate() Raw Codec Activation Success L16@8000hz 1 channel
20ms
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:400
switch_core_session_run() (OPENZAP/42) State RING
2008-01-04 15:45:09 [DEBUG] mod_openzap.c:276 channel_on_ring()
OPENZAP/42 CHANNEL RING
2008-01-04 15:45:09 [DEBUG] switch_ivr_originate.c:48
originate_on_ring() OPENZAP/42 State Change CS_RING -> CS_HOLD
2008-01-04 15:45:09 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OPENZAP/42 [BREAK]
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:415
switch_core_session_run() (OPENZAP/42) State HOLD
2008-01-04 15:45:09 [DEBUG] switch_core_state_machine.c:204
switch_core_standard_on_hold() Standard HOLD
freeswitch@sipxpbx.oneconv.com>
freeswitch@sipxpbx.oneconv.com >
freeswitch@sipxpbx.oneconv.com> 2008-01-04 15:45:39 [DEBUG]
zap_analog.c:244 zap_analog_channel_run() Changing state on 2:1 from DIALING
to BUSY
2008-01-04 15:45:40 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 2:1 for BUSY
2008-01-04 15:45:40 [DEBUG] zap_analog.c:467 zap_analog_channel_run()
Changing state on 2:1 from BUSY to DOWN
2008-01-04 15:45:40 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 2:1 for DOWN
2008-01-04 15:45:40 [DEBUG] mod_openzap.c:916 on_fxo_signal() got FXO
sig 2:1 [STOP]
2008-01-04 15:45:40 [NOTICE] mod_openzap.c:934 on_fxo_signal() Hangup
OPENZAP/42 [CS_HOLD] [NORMAL_CIRCUIT_CONGESTION]
2008-01-04 15:45:40 [DEBUG] switch_channel.c:1071
switch_channel_perform_hangup() Kill OPENZAP/42 [KILL]
2008-01-04 15:45:40 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OPENZAP/42 [BREAK]
2008-01-04 15:45:40 [DEBUG] zap_analog.c:648 zap_analog_channel_run()
ANALOG CHANNEL thread ended.
2008-01-04 15:45:40 [DEBUG] switch_core_state_machine.c:394
switch_core_session_run() (OPENZAP/42) State HANGUP
2008-01-04 15:45:40 [WARNING] mod_openzap.c:319 channel_on_hangup() VETO
Changing state on 2:1 from DOWN to HANGUP
2008-01-04 15:45:40 [DEBUG] mod_openzap.c:359 channel_on_hangup()
OPENZAP/42 CHANNEL HANGUP
2008-01-04 15:45:40 [DEBUG] switch_core_state_machine.c:45
switch_core_standard_on_hangup() Standard HANGUP OPENZAP/42, cause:
NORMAL_CIRCUIT_CONGESTION
2008-01-04 15:45:40 [DEBUG] switch_core_session.c:683
switch_core_session_thread() Session 4 (OPENZAP/42) Locked, Waiting on
external entities
2008-01-04 15:45:40 [DEBUG] switch_ivr_originate.c:873
switch_ivr_originate() Originate Resulted in Error Cause: 34
[NORMAL_CIRCUIT_CONGESTION]
2008-01-04 15:45:40 [INFO] mod_dptools.c:1331 audio_bridge_function()
Originate Failed.  Cause: NORMAL_CIRCUIT_CONGESTION
2008-01-04 15:45:40 [NOTICE] mod_dptools.c:1358 audio_bridge_function()
Hangup OpenZAP/42 [CS_EXECUTE] [NORMAL_CIRCUIT_CONGESTION]
2008-01-04 15:45:40 [DEBUG] switch_channel.c:1071
switch_channel_perform_hangup() Kill OpenZAP/42 [KILL]
2008-01-04 15:45:40 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OpenZAP/42 [BREAK]
2008-01-04 15:45:40 [DEBUG] switch_core_state_machine.c:394
switch_core_session_run() (OpenZAP/42) State HANGUP
2008-01-04 15:45:40 [DEBUG] mod_openzap.c:329 channel_on_hangup()
Changing state on 1:1 from UP to HANGUP
2008-01-04 15:45:40 [DEBUG] mod_openzap.c:359 channel_on_hangup()
OpenZAP/42 CHANNEL HANGUP
2008-01-04 15:45:40 [DEBUG] switch_core_state_machine.c:45
switch_core_standard_on_hangup() Standard HANGUP OpenZAP/42, cause:
NORMAL_CIRCUIT_CONGESTION
2008-01-04 15:45:40 [DEBUG] switch_core_session.c:683
switch_core_session_thread() Session 3 (OpenZAP/42) Locked, Waiting on
external entities
2008-01-04 15:45:40 [INFO] switch_core_session.c:689
switch_core_session_thread() Session 3 (OpenZAP/42) Ended
2008-01-04 15:45:40 [NOTICE] switch_core_session.c:691
switch_core_session_thread() Close Channel OpenZAP/42 [CS_HANGUP]
2008-01-04 15:45:40 [INFO] switch_core_session.c:689
switch_core_session_thread() Session 4 (OPENZAP/42) Ended
2008-01-04 15:45:40 [NOTICE] switch_core_session.c:691
switch_core_session_thread() Close Channel OPENZAP/42 [CS_HANGUP]
2008-01-04 15:45:40 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for HANGUP
2008-01-04 15:45:40 [DEBUG] zap_analog.c:290 zap_analog_channel_run()
Changing state on 1:1 from HANGUP to BUSY
2008-01-04 15:45:40 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for BUSY
2008-01-04 15:45:53 [DEBUG] zap_analog.c:664 process_event() EVENT
[ONHOOK][1:1] STATE [BUSY]
2008-01-04 15:45:53 [DEBUG] zap_analog.c:690 process_event() Changing
state on 1:1 from BUSY to DOWN
2008-01-04 15:45:53 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for DOWN
2008-01-04 15:45:53 [DEBUG] mod_openzap.c:968 on_fxs_signal() got FXS
sig [STOP]
2008-01-04 15:45:53 [DEBUG] zap_analog.c:648 zap_analog_channel_run()
ANALOG CHANNEL thread ended.
Thanks,
Irshad.
On Jan 3, 2008 7:43 PM, Anthony Minessale < anthmct@yahoo.com> wrote:
...
What does openzap.conf.xml look like?
Perhaps you are using the default which only has 1 span defined.
Try cloning the whole <span id="1"> block so there
is a span 1 and 2 like this:
<configuration name=" openzap.conf" description="OpenZAP
Configuration">
  <settings>
    <param name="debug" value="0"/>
  </settings>
  <analog_spans>
    <span id="1">
      <param name="tonegroup" value="us"/>
      <param name="digit-timeout" value="2000"/>
      <param name="max-digits" value="11"/>
      <param name="dialplan" value="XML"/>
      <param name="context" value="default"/>
      <!-- regex to stop dialing when it matches -->
      <!--<param name="dial-regex" value="5555"/>-->
      <!-- regex to stop dialing when it does not match -->
      <!--<param name="fail-dial-regex" value="^5"/>-->
    </span>
<span id="2">
      <param name="tonegroup" value="us"/>
      <param name="digit-timeout" value="2000"/>
      <param name="max-digits" value="11"/>
      <param name="dialplan" value="XML"/>
      <param name="context" value="default"/>
      <!-- regex to stop dialing when it matches -->
      <!--<param name="dial-regex" value="5555"/>-->
      <!-- regex to stop dialing when it does not match -->
      <!--<param name="fail-dial-regex" value="^5"/>-->
    </span>
</analog_spans>
</configuration>
Anthony Minessale II
FreeSWITCH http://www.freeswitch.org/
ClueCon http://www.cluecon.com/
AIM: anthm
MSN:anthony_minessale@hotmail.com
GTALK/JABBER/PAYPAL:anthony.minessale@gmail.com
IRC: irc.freenode.net #freeswitch
FreeSWITCH Developer Conference
sip:888@conference.freeswitch.org
iax:guest@conference.freeswitch.org/888
googletalk:conf+888@conference.freeswitch.org
pstn:213-799-1400
----- Original Message ----
From: Irshad Ahamed <irshad.fswitch@gmail.com >
To: freeswitch-dev@lists.freeswitch.org; freeswitch-users@lists.freeswitch.org
Sent: Wednesday, January 2, 2008 12:40:14 AM
Subject: [Freeswitch-users] Not able to make an outgoing Call through
FXO....
Hi,
Wishing U all a very Happy n Prosperous New Year!!!!
I am trying to make an outgoing call using FXO connected to an
external telephone line.
Here is the set-up:
1. FXO connected to external telephone line
2. FXS connected to analog phone.
The Openzap.conf @ /etc/openzap is as follows:
[span zt]
name => OpenZAP
number => 1
fxs-channel => 1
[span zt]
name => OpenZAP
number => 1
fxo-channel => 4
The default.xml @  /usr/local/freeswitch/conf/dialplan is configured
for inward and outgoing calls on FXO as follows:
<extension name="outgoing-fxo">
    <condition field="destination_number" expression="^(43)$">
      <action application="bridge" data="openzap/2/1/43"/>
    </condition>
  </extension>
<extension name="incoming-fxo">
    <condition field="destination_number" expression="^(35)$">
      <action application="bridge" data="openzap/1/1"/>
    </condition>
  </extension>
While Start-up Freeswitch following logs were seen:
2008-01-02 11:51:22 [DEBUG] zap_io.c:1770 load_config() found config
for span
2008-01-02 11:51:22 [DEBUG] zap_io.c:1797 load_config() created span 1
of type zt
2008-01-02 11:51:22 [DEBUG] zap_io.c:1810 load_config() span 1
[name]=[OpenZAP]
2008-01-02 11:51:22 [DEBUG] zap_io.c:1810 load_config() span 1
[number]=[1]
2008-01-02 11:51:22 [DEBUG] zap_io.c:1810 load_config() span 1
[fxs-channel]=[1]
2008-01-02 11:51:22 [DEBUG] zap_io.c:1850 load_config() setting trunk
type to 'FXS' start(KEWL)
2008-01-02 11:51:22 [INFO] zap_zt.c:168 zt_open_range() configuring
device /dev/zap/channel channel 1 as OpenZAP device 1:1 fd:31
2008-01-02 11:51:22 [DEBUG] zap_io.c:1770 load_config() found config
for span
2008-01-02 11:51:22 [DEBUG] zap_io.c:1797 load_config() created span 2
of type zt
2008-01-02 11:51:22 [DEBUG] zap_io.c:1810 load_config() span 2
[name]=[OpenZAP]
2008-01-02 11:51:22 [DEBUG] zap_io.c:1810 load_config() span 2
[number]=[1]
2008-01-02 11:51:22 [DEBUG] zap_io.c:1810 load_config() span 2
[fxo-channel]=[4]
2008-01-02 11:51:22 [DEBUG] zap_io.c:1839 load_config() setting trunk
type to 'FXO' start(KEWL)
2008-01-02 11:51:22 [INFO] zap_zt.c:168 zt_open_range() configuring
device /dev/zap/channel channel 4 as OpenZAP device 2:1 fd:32
2008-01-02 11:51:22 [INFO] zap_io.c:1881 load_config() Configured 2
channel(s)
2008-01-02 11:51:22 [CONSOLE] switch_loadable_module.c:748
switch_loadable_module_load_file() Successfully Loaded [mod_openzap]
and while I made a call following logs were seen:
2008-01-02 12:04:16 [NOTICE] switch_core_state_machine.c:134
switch_core_standard_on_execute() Execute bridge(openzap/2/1/43)2008-01-02
12:04:16 [DEBUG] mod_openzap.c:231 tech_init() Set codec PCMU 20ms
2008-01-02 12:04:16 [NOTICE] switch_channel.c:392
switch_channel_set_name() New Chan OPENZAP/43
[e3630387-25d6-4031-bf81-239c3e64e3fa]
2008-01-02 12:04:16 [DEBUG] mod_openzap.c:802
channel_outgoing_channel() OPENZAP/43 State Change CS_NEW -> CS_INIT
2008-01-02 12:04:16 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OPENZAP/43 [BREAK]
2008-01-02 12:04:16 [ERR] zap_io.c:884 zap_channel_outgoing_call()
outgoing_call method not implemented!
2008-01-02 12:04:16 [NOTICE] mod_openzap.c:818
channel_outgoing_channel() Close Channel OPENZAP/43 [CS_INIT]
2008-01-02 12:04:16 [ERR] switch_ivr_originate.c:525
switch_ivr_originate() Cannot Create Outgoing Channel! cause:
DESTINATION_OUT_OF_ORDER
2008-01-02 12:04:16 [DEBUG] switch_ivr_originate.c:873
switch_ivr_originate() Originate Resulted in Error Cause: 27
[DESTINATION_OUT_OF_ORDER]
2008-01-02 12:04:16 [INFO] mod_dptools.c:1331 audio_bridge_function()
Originate Failed.  Cause: DESTINATION_OUT_OF_ORDER
2008-01-02 12:04:16 [NOTICE] mod_dptools.c:1358
audio_bridge_function() Hangup OpenZAP/43 [CS_EXECUTE]
[DESTINATION_OUT_OF_ORDER]
2008-01-02 12:04:16 [DEBUG] switch_channel.c:1071
switch_channel_perform_hangup() Kill OpenZAP/43 [KILL]
2008-01-02 12:04:16 [DEBUG] switch_core_session.c:625
switch_core_session_signal_state_change() Kill OpenZAP/43 [BREAK]
2008-01-02 12:04:16 [DEBUG] switch_core_state_machine.c:394
switch_core_session_run() (OpenZAP/43) State HANGUP
2008-01-02 12:04:16 [DEBUG] mod_openzap.c:329 channel_on_hangup()
Changing state on 1:1 from IDLE to HANGUP
2008-01-02 12:04:16 [DEBUG] mod_openzap.c:359 channel_on_hangup()
OpenZAP/43 CHANNEL HANGUP
2008-01-02 12:04:16 [DEBUG] switch_core_state_machine.c:45
switch_core_standard_on_hangup() Standard HANGUP OpenZAP/43, cause:
DESTINATION_OUT_OF_ORDER
2008-01-02 12:04:16 [DEBUG] switch_core_session.c:683
switch_core_session_thread() Session 1 (OpenZAP/43) Locked, Waiting on
external entities
2008-01-02 12:04:16 [INFO] switch_core_session.c:689
switch_core_session_thread() Session 1 (OpenZAP/43) Ended
2008-01-02 12:04:16 [NOTICE] switch_core_session.c:691
switch_core_session_thread() Close Channel OpenZAP/43 [CS_HANGUP]
2008-01-02 12:04:16 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for HANGUP
2008-01-02 12:04:17 [DEBUG] zap_analog.c:290 zap_analog_channel_run()
Changing state on 1:1 from HANGUP to BUSY
2008-01-02 12:04:17 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for BUSY
2008-01-02 12:04:20 [DEBUG] zap_analog.c:664 process_event() EVENT
[ONHOOK][1:1] STATE [BUSY]
2008-01-02 12:04:20 [DEBUG] zap_analog.c:690 process_event() Changing
state on 1:1 from BUSY to DOWN
2008-01-02 12:04:20 [DEBUG] zap_analog.c:351 zap_analog_channel_run()
Executing state handler on 1:1 for DOWN
2008-01-02 12:04:20 [DEBUG] mod_openzap.c:968 on_fxs_signal() got FXS
sig [STOP]
2008-01-02 12:04:20 [DEBUG] zap_analog.c:648 zap_analog_channel_run()
ANALOG CHANNEL thread ended.
Could anyone help me out in getting FXO working ???
Thanks in advance...
BR,
Irshad.
------------------------------
Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try
it now.<http://us.rd.yahoo.com/evt=51733/*http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ+>
_______________________________________________
Freeswitch-users mailing list
Freeswitch-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org
------------------------------
Looking for last minute shopping deals? Find them fast with Yahoo!
Search.<http://us.rd.yahoo.com/evt=51734/*http://tools.search.yahoo.com/newsearch/category.php?category=shopping>
_______________________________________________
Freeswitch-users mailing list
Freeswitch-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org
_______________________________________________
Freeswitch-users mailing list
Freeswitch-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org
_______________________________________________
Freeswitch-users mailing list
Freeswitch-users@lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

Re: [Freeswitch-dev] [Freeswitch-users] Not able to make an outgoing Call through FXO....

Irshad Ahamed

Irshad Ahamed

tags

participants (1)