all you need is..<div><br></div><div><action application="bridge" data="{sip_cid_type=rpid}sofia/**YOURPROFILE**/$1@**CISCOIP**" /></div><div><br></div><div>not all IOS's are going to need the caller ID to be forced to rpid,</div>
<div>but in my experience I needed it. ( it should not hurt anyways )</div><div><br></div><div>hope that helps</div><div><br></div><div>Jay</div><div><br><div class="gmail_quote">On Tue, Mar 9, 2010 at 6:18 PM, Stephen Kingham <span dir="ltr"><<a href="mailto:Stephen.Kingham@kingtech.com.au">Stephen.Kingham@kingtech.com.au</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex;">Hi<br>
<br>
I can help out with the Cisco config, but I have not worked out what I<br>
need to configure FreeSWITCH to route a SIP call to the ip address of<br>
the Cisco GW. If I could get a bit of help there I will write, or help<br>
write howto.<br>
<br>
Regards<br>
<br>
Stevek<br>
<br>
<br>
On Mon, 2010-03-08 at 18:23 +0100, Tristan Mahé wrote:<br>
> +1 with Brian,<br>
><br>
> Just as I have 5 spare minutes and to be kind:<br>
><br>
><br>
> * E1 controller config:<br>
><br>
> controller E1 0/0/0<br>
> framing NO-CRC4<br>
> pri-group timeslots 1-31<br>
> description E1_1<br>
> !<br>
> interface Serial0/0/0:15<br>
> no ip address<br>
> encapsulation hdlc<br>
> isdn switch-type primary-net5<br>
> isdn not-end-to-end 64<br>
> isdn incoming-voice voice<br>
> isdn bchan-number-order descending round-robin<br>
> no cdp enable<br>
> !<br>
> voice-port 0/0/0:15<br>
> no comfort-noise<br>
> cptone FR<br>
> timeouts call-disconnect 1<br>
> timeouts wait-release 1<br>
> !<br>
><br>
> * Dial-peers ( SIP to E1 and E1 to SIP):<br>
><br>
> dial-peer voice 100 pots<br>
> description SIP_TO_E1<br>
> destination-pattern 0........<br>
> progress_ind setup enable 3<br>
> progress_ind progress enable 8<br>
> progress_ind connect enable 8<br>
> progress_ind disconnect enable 8<br>
> no digit-strip<br>
> port 0/0/0:15<br>
> !<br>
> dial-peer voice 500 voip<br>
> description E1_TO_SIP<br>
> destination-pattern ....<br>
> progress_ind setup enable 3<br>
> session protocol sipv2<br>
> session target ipv4:FREESWITCH_IP<br>
> session transport udp<br>
> dtmf-relay rtp-nte<br>
> codec g711alaw<br>
> no vad<br>
> !<br>
><br>
><br>
> Remember to adapt this config to your needs ( there are mandatory<br>
> missing parts, but at least you have some config options to look for).<br>
><br>
> Regards,<br>
><br>
> Gled.<br>
><br>
> Brian West a écrit :<br>
> > You seem rather needy. Have you even tried google yet? When asking for help you could be more descriptive if you want help. These "I need help" without any directed questioned signals to me you have a job to do and you don't know how to do it and you're now asking US to do your job for you. Be descriptive and do some research yourself. Again we aren't cisco and you didn't pay us for that hardware so I would start by venturing over to <a href="http://www.cisco.com" target="_blank">www.cisco.com</a> and searching their docs for that hardware on how to configure voice peers. Then ask questions if anything is left to question.<br>
> ><br>
> > /b<br>
> ><br>
> > On Mar 8, 2010, at 9:23 AM, srinivasula reddy wrote:<br>
> ><br>
> >> HI,<br>
> >><br>
> >> how do i configure freeswitch gateway to communicate to cisco router, i am using cisco2921.<br>
> >><br>
> >> Thanks<br>
> >> Srinivas<br>
> ><br>
> ><br>
> > _______________________________________________<br>
> > FreeSWITCH-users mailing list<br>
> > <a href="mailto:FreeSWITCH-users@lists.freeswitch.org">FreeSWITCH-users@lists.freeswitch.org</a><br>
> > <a href="http://lists.freeswitch.org/mailman/listinfo/freeswitch-users" target="_blank">http://lists.freeswitch.org/mailman/listinfo/freeswitch-users</a><br>
> > UNSUBSCRIBE:<a href="http://lists.freeswitch.org/mailman/options/freeswitch-users" target="_blank">http://lists.freeswitch.org/mailman/options/freeswitch-users</a><br>
> > <a href="http://www.freeswitch.org" target="_blank">http://www.freeswitch.org</a><br>
><br>
> _______________________________________________<br>
> FreeSWITCH-users mailing list<br>
> <a href="mailto:FreeSWITCH-users@lists.freeswitch.org">FreeSWITCH-users@lists.freeswitch.org</a><br>
> <a href="http://lists.freeswitch.org/mailman/listinfo/freeswitch-users" target="_blank">http://lists.freeswitch.org/mailman/listinfo/freeswitch-users</a><br>
> UNSUBSCRIBE:<a href="http://lists.freeswitch.org/mailman/options/freeswitch-users" target="_blank">http://lists.freeswitch.org/mailman/options/freeswitch-users</a><br>
> <a href="http://www.freeswitch.org" target="_blank">http://www.freeswitch.org</a><br>
<br>
<br>
_______________________________________________<br>
FreeSWITCH-users mailing list<br>
<a href="mailto:FreeSWITCH-users@lists.freeswitch.org">FreeSWITCH-users@lists.freeswitch.org</a><br>
<a href="http://lists.freeswitch.org/mailman/listinfo/freeswitch-users" target="_blank">http://lists.freeswitch.org/mailman/listinfo/freeswitch-users</a><br>
UNSUBSCRIBE:<a href="http://lists.freeswitch.org/mailman/options/freeswitch-users" target="_blank">http://lists.freeswitch.org/mailman/options/freeswitch-users</a><br>
<a href="http://www.freeswitch.org" target="_blank">http://www.freeswitch.org</a><br>
</blockquote></div><br><br clear="all"><br>-- <br>Sincerely<br><br>Jay<br>
</div>