[Freeswitch-users] How to find destination IP address of b-leg in "show calls" or alike?

[Michael Jerris]

That doesn’t sound right to me.  Are you sure?

> On Sep 2, 2016, at 2:22 PM, Victor Chukalovskiy <victor.chukalovskiy at gmail.com> wrote:
> 
> The IP I saw in the actual "show channels" dump represents the value of 
> the far-end signaling IP for incoming (a-leg) of the call. However, for 
> b-leg of the call the IP value printed is the far-end IP of the 
> corresponding a-leg. So the variable is not just named differently, but 
> also doesn't contain expected value for the b-leg of the call.
> 
> On 16-09-02 01:22 PM, Michael Jerris wrote:
>> look at the actual data.  it doesn’t have the same name ...
>> 
>>> On Sep 2, 2016, at 12:47 PM, Victor Chukalovskiy <victor.chukalovskiy at gmail.com> wrote:
>>> 
>>> Michael,  saw your answer thank you. Yes, would prefer not to mess with DB.
>>> 
>>> I searched and I couldn't find the value of ${network_address} in "show
>>> channels" output. I'm on 1.6.6 still if it matters. Here is the header
>>> row of "show channels":
>>> 
>>> uuid,direction,created,created_epoch,name,state,cid_name,cid_num,ip_addr,dest,application,application_data,dialplan,context,read_codec,read_rate,read_bit_rate,write_codec,write_rate,write_bit_rate,secure,hostname,presence_id,presence_data,callstate,callee_name,callee_num,callee_direction,call_uuid,sent_callee_name,sent_callee_num,initial_cid_name,initial_cid_num,initial_ip_addr,initial_dest,initial_dialplan,initial_context
>>> 
>>> "network_address" isn't there :(
>>> 
>>> On 16-09-02 12:34 PM, Michael Jerris wrote:
>>>> see my previous answer to this question on this thread.  You don’t need to mess with anything, its already there.
>>>> 
>>>>> On Sep 1, 2016, at 10:11 PM, Victor Chukalovskiy <victor.chukalovskiy at gmail.com> wrote:
>>>>> 
>>>>> Thank you, that would be for a specific call. Anything that will do for all calls at once?
>>>>> 
>>>>>   Original Message
>>>>> From: Stanislav Sinyagin
>>>>> Sent: Thursday, September 1, 2016 21:16
>>>>> To: FreeSWITCH Users Help
>>>>> Reply To: FreeSWITCH Users Help
>>>>> Subject: Re: [Freeswitch-users] How to find destination IP address of b-leg in "show calls" or alike?
>>>>> 
>>>>> uuid_dump should show all variables
>>>>> 
>>>>> On Thu, Sep 1, 2016 at 8:49 PM, Victor Chukalovskiy
>>>>> <victor.chukalovskiy at gmail.com> wrote:
>>>>>> Good day, I've been studying output of "show calls", "show detailed
>>>>>> calls", and "show channels" for quite some time.
>>>>>> 
>>>>>> Surprisingly, I can't find a value of ${network_address} variable or
>>>>>> anything similar that will tell me for each outgoing leg SIP IP address
>>>>>> on the far end. In other words, how do I find IP address of SIP UAS
>>>>>> FreeSWITCH is communicating with on every outgoing call leg?
>>>>>> 
>>>>>> I managed to get it in CDRs by dumping ${network_address}, but can't get
>>>>>> it for active calls dump. Is there truly nothing in "show calls" or
>>>>>> equivalent that will help me? Should I submit a feature request then?
>>>>>> 
>>>>>> Few cents on my call scenario:
>>>>>> 
>>>>>> SIP call coming in (a-leg) --> multiple sip calls going out (b-legs).
>>>>>> I'm originating my b-legs via sofia gateways (so IP address of the
>>>>>> far-end is picked up from gateway config, and not mentioned in the
>>>>>> dial-plan in any way or form).
>>>>>> 
>>>>>> Many thanks,
>>>>>> 
>>>>>> -Victor