[Freeswitch-users] Call forwarding to mobile showing our trunk CLI instead of caller CLI

[Avi Marcus]

It's basically set automatically -- the caller id from the inbound route is
used when you bridge. As you said:

> All the internal extensions see the caller ID no problem

So therefore, either you are sending the caller ID in the wrong format to
your carrier - RPID, pid, "From:", OR as I said, they are fixing your
outbound caller ID.

Are you in the UK? I know outbound calls via numbergroup only allows you to
use CIDs registered on my account. I usually use xconnect to terminate to
UK and afaik, they pass along the CID. Perhaps you need a backup carrier,
and one that you use especially for these calls.

-Avi


On Fri, May 4, 2012 at 3:04 AM, Neil Stirton <neil.stirton at ikiji.com> wrote:

> Hi Avi,
>
> Set that to true but feel like I need to be passing through some more info
> when bridging the call?
>
> You are most likely right that the trunk is controls what number is
> displayed on outbound calls … this I will check also.
>
> Many thanks,
> Neil
>
>  From: Avi Marcus <avi at avimarcus.net>
> Reply-To: FreeSWITCH Users Help <freeswitch-users at lists.freeswitch.org>
> Date: Thursday, 3 May 2012 23:20
> To: FreeSWITCH Users Help <freeswitch-users at lists.freeswitch.org>
> Subject: Re: [Freeswitch-users] Call forwarding to mobile showing our
> trunk CLI instead of caller CLI
>
> Depending on your trunk provider, they might not allow you to change your
> outbound caller ID. It might be hard-coded for your account.
>
> If not.. it could be you need to set "caller-id-in-from" to be true
> within the gateway and reload the gateway.
>
> -Avi
>
>
> On Fri, May 4, 2012 at 12:33 AM, Neil Stirton <neil.stirton at ikiji.com>wrote:
>
>> Hi,
>>
>> Apologies for the noob question here.
>>
>> Setup Freeswitch on CentOS and using FusionPBX for 'easy' management.
>>
>> I've defined a hunt group (ext 7001) which simultaneously rings 3
>> internal SIP extensions + my mobile.
>>
>> All the internal extensions see the caller ID no problem but because I am
>> also sending the call back out through our ITSP's trunk, the call always
>> shows as our office calling my mobile phone rather than the actual caller's
>> ID.
>> I have the hunt group calling:
>>
>>   Sip uri    sofia/gateway/<gateway>/<my-mobile>
>>
>> I'm sure it's a case of a variable setting something but if someone could
>> point me in the right direction that would be very much appreciated.
>>
>> Many thanks
>> Neil
>>
>> _________________________________________________________________________
>> Professional FreeSWITCH Consulting Services:
>> consulting at freeswitch.org
>> http://www.freeswitchsolutions.com
>>
>> 
>> 
>>
>> Official FreeSWITCH Sites
>> http://www.freeswitch.org
>> http://wiki.freeswitch.org
>> http://www.cluecon.com
>>
>> FreeSWITCH-users mailing list
>> FreeSWITCH-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>>
>
> _________________________________________________________________________
> Professional FreeSWITCH Consulting Services:
> consulting at freeswitch.org
> http://www.freeswitchsolutions.com
>
> 
> 
>
> Official FreeSWITCH Sites
> http://www.freeswitch.org
> http://wiki.freeswitch.org
> http://www.cluecon.com
>
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20120504/23e92448/attachment.html