[Freeswitch-users] UUID_Bridge Fails But Reports +OK

Peter Olsson peter.olsson at visionutveckling.se
Wed May 25 12:52:59 MSD 2011


You need to provide the entire debug trace from this, nor just only after calling uuid_bridge.

/Peter
________________________________________
Från: freeswitch-users-bounces at lists.freeswitch.org [freeswitch-users-bounces at lists.freeswitch.org] för Antonio Teixeira [eagle.antonio at gmail.com]
Skickat: den 25 maj 2011 10:32
Till: FreeSWITCH Users Help
Ämne: Re: [Freeswitch-users] UUID_Bridge Fails But Reports +OK

Good Morning List As Promised.

I Have tested with G711 the problem remains and appears not be affected by the codec change.

Here i have my debug log :
http://pastebin.freeswitch.org/16369

Just a short explanation :

the call XXXX1010 is Leg A and is currently valet_park()

call XXXX371 is Leg B and is currently on park()

Strangely FS says LEG A is out of order but i can hear MOH and sometimes with this exact software it connects fine.

Hope you can help me out i will keep testing during the day.

Regards
A/T


2011/5/24 Antonio Teixeira <eagle.antonio at gmail.com<mailto:eagle.antonio at gmail.com>>
Ok Anthony.

I will provide you with data regarding the use of G711 and full debug logs.
Will keep an eye on the logs.

Regards
A/T


2011/5/24 Anthony Minessale <anthony.minessale at gmail.com<mailto:anthony.minessale at gmail.com>>
The +OK only means the attempt to bridge was successful, if something
else goes wrong after that, you will not know because it happens
later.

As suggested, look at the cause of the hangup on the failed bridge.


On Tue, May 24, 2011 at 4:33 AM, Antonio Teixeira
<eagle.antonio at gmail.com<mailto:eagle.antonio at gmail.com>> wrote:
> Hello List , Good Morning.
>
> In my fight to get ESL & Python & Freeswitch all to behave properly i
> noticed a possible BUG ( need the veterans to confirm).
>
> Scenario :
>
> Originate & ValetPark () + MOH OR  Just Park() , Both show the same problem.
> Codec G729
>
> I Make another call:
> originate & park()
> codec G729
>
> Now Python ESL Inbound Or FS Console :
>
> uuid_bridge uuid1 uuid2
>
> +OK uuid
>
> Now one of the two things happen :
>
> 1) One the call gets connected hurray :) , Audio Perfect  , etc.
>
> 2) The call gets dropped :(
>
> In both cases uuid_bridge reports +OK even in the case the call is dropped.
> Even if i Park() Both Calls using the dialplan XML ( NO ESL with those
> SYN/ASYNC Problems)  I still get sometimes ( not always) a dropped call
> could this be related to the use of G729 ?
>
> I have lots of available licenses.
>
> Regards
> António Teixeira
>
>
>
>
>
> _______________________________________________
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org<mailto:FreeSWITCH-users at lists.freeswitch.org>
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>



--
Anthony Minessale II

FreeSWITCH http://www.freeswitch.org/
ClueCon http://www.cluecon.com/
Twitter: http://twitter.com/FreeSWITCH_wire

AIM: anthm
MSN:anthony_minessale at hotmail.com<mailto:MSN%3Aanthony_minessale at hotmail.com>
GTALK/JABBER/PAYPAL:anthony.minessale at gmail.com<mailto:PAYPAL%3Aanthony.minessale at gmail.com>
IRC: irc.freenode.net<http://irc.freenode.net> #freeswitch

FreeSWITCH Developer Conference
sip:888 at conference.freeswitch.org<mailto:sip%3A888 at conference.freeswitch.org>
googletalk:conf+888 at conference.freeswitch.org<mailto:googletalk%3Aconf%2B888 at conference.freeswitch.org>
pstn:+19193869900

_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users at lists.freeswitch.org<mailto:FreeSWITCH-users at lists.freeswitch.org>
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org


!DSPAM:4ddcbfed32761527616399!



More information about the FreeSWITCH-users mailing list