[Freeswitch-users] ESL Inbound - what would be the best known way to wait in XML dialplan for any command execution via ESL?

[Anton VG]

very similar...

2011/6/11 Peter Olsson <peter.olsson at visionutveckling.se>:
> I do it like this;
>
> First I separate calls in the dialplan, those calls with a destination to my "IVR" i will first set a variable, for instance "ivr=true", I then park the call in the dialplan. In my ESL app I wait for the CALL_PARKED event, I then check if the var is set on the call - if it is I start handling it.
>
> /Peter
> ________________________________________
> Från: freeswitch-users-bounces at lists.freeswitch.org [freeswitch-users-bounces at lists.freeswitch.org] f&#246;r Anton VG [anton.vazir at gmail.com]
> Skickat: den 11 juni 2011 18:07
> Till: FreeSWITCH Users Help
> Ämne: Re: [Freeswitch-users] ESL Inbound - what would be the best known way to wait in XML dialplan for any command execution via ESL?
>
> now actually I do park over ESL, as soon as I get channel_create
> message, and there is only a single command in the XML dialplan: pause
> 1000. I was hoping there is a better approach to this.
>
> PS. Outbound ESL showed itself as a terribly bad scaling solution if
> implemented in python...
>
> 2011/6/11 Peter Olsson <peter.olsson at visionutveckling.se>:
>> PARK is the only way to handle this in a good way. If you can't separate the calls directly in the dial plan, you could probably do a transfer of the call (that you don't want to handle) inside your app, to another extension in the dial plan.
>>
>> /Peter
>> ________________________________________
>> Från: freeswitch-users-bounces at lists.freeswitch.org [freeswitch-users-bounces at lists.freeswitch.org] f&#246;r Anton VG [anton.vazir at gmail.com]
>> Skickat: den 11 juni 2011 17:40
>> Till: FreeSWITCH Users Help
>> Ämne: [Freeswitch-users] ESL Inbound - what would be the best known way to wait in XML dialplan for any command execution via ESL?
>>
>> Hi!
>>
>> Switched from outbound ESL to an INBOUND mode, for controlling the
>> incoming CALL flow: so when call comes, Inbound ESL app catches
>> corresponding event and executes the necessary command on the caller
>> UUID.
>>
>> My question is: In XML dialplan, when call comes, if do not PARK it or
>> do PAUSE, the ESL controlling application is too late to execute park
>> before XML dialplan ends, and disconnect the call.
>>
>> PARK shows itself as not a good solution, since if call did not
>> handled by ESL - it stales.
>> PAUSE - i would not like to add extra delays to call handling.
>>
>> I suppose there should be a known good way to handle in XML dialplan
>> if anything else executed on the given channel/uuid?
>>
>> Regards,
>> Anton.
>>
>> _______________________________________________
>> FreeSWITCH-users mailing list
>> FreeSWITCH-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>>
>>
>>
>> _______________________________________________
>> FreeSWITCH-users mailing list
>> FreeSWITCH-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>
> _______________________________________________
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
> !DSPAM:4df392d332762225017462!
>
>
> _______________________________________________
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>