[Freeswitch-users] Call quality issues

[Eric Beard]

On the bad machine, I just did a make clean, re-ran bootstrap.sh, configure, make, then make install, and now it works fine.  I'm mystified.  I really wish I knew what the problem was so I can avoid it in the future.

The only possible cause I can think of is that at some point I needed to rebuild to use an extra module (like curl), and I did a make, make install, without doing a make clean, and somehow that was related?  Sounds iffy.

-----------------------
Eric Z. Beard, CTO
Loop LLC
w (877) 850-2010 x9249
m (727) 776-2768
eric at loopfx.com<mailto:eric at loopfx.com>

From: freeswitch-users-bounces at lists.freeswitch.org [mailto:freeswitch-users-bounces at lists.freeswitch.org] On Behalf Of Michael Collins
Sent: Friday, April 29, 2011 1:33 PM
To: FreeSWITCH Users Help
Subject: Re: [Freeswitch-users] Call quality issues

What about the operating system? Same rev, same kernel, same timing?
-MC
On Fri, Apr 29, 2011 at 10:10 AM, Eric Beard <eric at loopfx.com<mailto:eric at loopfx.com>> wrote:
It seems to be a CPU issue.

I started from scratch today with a new machine, same exact hardware, and I am running 20 calls at less than 1% CPU, with perfect audio quality (same as the bad machine before it went bad).

On the bad machine, 20 calls causes the CPU to be at 20%, and quality is shaky.  30 calls and it's terrible.  Only the freeswitch process is eating CPU.

I have diffed the conf folders and everything is the same.  This is driving me nuts.  I have no idea  what I did to that machine to ruin the performance.

-----------------------
Eric Z. Beard, CTO
Loop LLC
w (877) 850-2010 x9249
m (727) 776-2768
eric at loopfx.com<mailto:eric at loopfx.com>

From: freeswitch-users-bounces at lists.freeswitch.org<mailto:freeswitch-users-bounces at lists.freeswitch.org> [mailto:freeswitch-users-bounces at lists.freeswitch.org<mailto:freeswitch-users-bounces at lists.freeswitch.org>] On Behalf Of Michael Collins
Sent: Friday, April 29, 2011 12:57 PM
To: FreeSWITCH Users Help
Subject: Re: [Freeswitch-users] Call quality issues


On Thu, Apr 28, 2011 at 2:52 PM, Eric Beard <eric at loopfx.com<mailto:eric at loopfx.com>> wrote:
Hello,

I ran into some major call quality issues this week, and I'm trying to figure out how to troubleshoot things.  I've been running FreeSwitch for a few weeks, and suddenly a few days ago my call quality dropped drastically.  I had been running more than 100 concurrent calls, with the CPU at less than 20%, but now at 20 concurrent calls, the CPU is still at a little less than 20%, and the call quality is bad - any higher and calls go almost completely silent.  There is a direct correlation between the number of simultaneous calls and call quality.

I have tested against multiple gateways, same results against each, so it's not an issue with the gateway.

I have captured packets on the machine and analyzed them with Wireshark.  It seems like the inbound packets are all fine, no jitter or loss.  But the packets being sent by FreeSwitch are degraded.

One sample call showed:

Drop by Jitter Buff:158(14.1%) Out of Seq 0 (0.0%) Wrong Timestamp 96(8.6%)

What is the topology of the network path for the above call? Also, where on the LAN/WAN did you capture these packets? Wrong timestamps and 14% dropped packets suggests that something on the network is interfering with the delivery of these packets in a timely manner.
-MC


_______________________________________________
FreeSWITCH-users mailing list
FreeSWITCH-users at lists.freeswitch.org<mailto:FreeSWITCH-users at lists.freeswitch.org>
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20110429/242f74cd/attachment-0001.html