[Freeswitch-users] Installing OpenZap?

[Tom Baldwin]

GillesToo,

What is the output of "dahi_scan"
can you post your openzap.conf.xml file
I run wanpipe , dahdi and openzap with libpri


Tom
 
On Fri, 2010-05-28 at 04:41 -0700, GillesToo wrote:
> 
> Troy Anderson-2 wrote:
> > oz list will only work if openzap is loaded, so that's a clue that it
> > isn't for some reason. Try issuing reload mod_openzap from the cli and
> > take a look at the output.  There is likely an error on load, and that
> > error may lead you to what's wrong with the config.
> 
> Thanks for the tip. Here's what "reload mod_openzap" returns:
> 
> 
> 
> > freeswitch at internal> load mod_openzap
> > -ERR [module load file routine returned an error]
> > 
> > freeswitch at internal> 2010-05-28 12:13:51.138275 [DEBUG] zap_config.c:56
> > Configuration file is /usr/local/freeswitch/conf/modules.conf.
> > 2010-05-28 12:13:51.138275 [NOTICE] zap_io.c:3057 Modules configured: 1 
> > 2010-05-28 12:13:51.139297 [DEBUG] zap_config.c:56 Configuration file is
> > /usr/local/freeswitch/conf/openzap.conf.
> > 2010-05-28 12:13:51.139297 [DEBUG] zap_io.c:2587 found config for span
> > 2010-05-28 12:13:51.139297 [NOTICE] ozmod_zt.c:1185 Using DAHDI control
> > device
> > 2010-05-28 12:13:51.139297 [ERR] ozmod_zt.c:1194 Cannot open control
> > device /dev/dahdi/ctl: Permission denied
> > 2010-05-28 12:13:51.140310 [ERR] zap_io.c:2856 Error loading
> > /usr/local/freeswitch/mod/ozmod_zt.so
> > 2010-05-28 12:13:51.140310 [ERR] zap_io.c:2901 Unloading
> > /usr/local/freeswitch/mod/ozmod_zt.so
> > 2010-05-28 12:13:51.140310 [CRIT] zap_io.c:2610 failure creating span, no
> > such type 'zt'
> > 2010-05-28 12:13:51.140310 [INFO] zap_io.c:2782 Configured 0 channel(s)
> > 2010-05-28 12:13:51.140310 [ERR] zap_io.c:3065 No modules configured!
> > 2010-05-28 12:13:51.140310 [ERR] mod_openzap.c:3331 Error loading OpenZAP
> > 2010-05-28 12:13:51.140310 [CRIT] switch_loadable_module.c:882 Error
> > Loading module /usr/local/freeswitch/mod/mod_openzap.so
> > **Module load routine returned an error**
> > 
> 
> BTW, before I investigate further... I notice that the two articles in the
> wiki about OpenZap are based on Zaptel (1.4), whose development stopped two
> years ago when Zaptel was replaces with Dadhi:
> 
> http://wiki.freeswitch.org/wiki/OpenZAP
> http://wiki.freeswitch.org/wiki/Zaptel_Tutorial
> 
> Has someone successfully used OpenZap with Dahdi, and if yes, are there any
> changes that should be made in OpenZap to accomodate this change?
> 
> Thank you.