[Freeswitch-users] span not defined error

[Moises Silva]

Hi Again Neil,

I just noticed your dial string is incorrect. The correct syntax is:

OpenZAP/<span>/<chan_code>/[number]

The span and chan code are mandatory. The number is optional ( FXS channels
do not require a number, they just ring the FXO device connected to them).

The span is either a number ( span id, the id is a number assigned in the
order in which the span is defined in openzap.conf ) or a span name also as
specified in the [span wanpipe <span_name>] line in openzap.conf

The chan code is either a number ( for spans that support individual channel
selection, boost is NOT one of them ), or a channel hunting mode, there is
currently 2 modes, "a" is top down and "A" is bottom up.

So, this is a valid string for you case:

OpenZAP/smg_prid/a/<number>

In the specific case of boost in socket mode ( openzap only supports socket
mode ) the number may contain @gX where X is a group ( for hunting as
configured in /etc/wanpipe/smg_pri.conf). Boost signaling are a special case
because the hunting for channels is not done within FreeSWITCH but in
sangoma_prid binary ( in the new OpenZAP version called FreeTDM this has
changed depending on configuration).

Bottom line, this should work:

OpenZAP/smg_prid/a/1234 at g1

If you have g1 configured in /etc/wanpipe/smg_pri.conf

Moises Silva
Senior Software Engineer
Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R 9T3
Canada
t. 1 905 474 1990 x 128 | e. moy at sangoma.com


On Sat, May 15, 2010 at 6:26 PM, Neil Patel <neilp at cs.stanford.edu> wrote:

> Span was originally in the boost section when I got this error, so I
> thought I'd try it in analog and both. None work.
>
> -Neil
>
> On Sat, May 15, 2010 at 3:18 PM, Moises Silva <moises.silva at gmail.com>wrote:
>
>> Why do you have 2 spans in openzap.conf.xml with the same name, in both
>> the boost and analog sections?
>> Moises Silva
>> Senior Software Engineer
>> Sangoma Technologies Inc. | 50 McIntosh Drive, Suite 120, Markham ON L3R
>> 9T3 Canada
>> t. 1 905 474 1990 x 128 | e. moy at sangoma.com
>>
>>
>> On Sat, May 15, 2010 at 3:52 PM, Neil Patel <neilp at cs.stanford.edu>wrote:
>>
>>> Hi All,
>>>
>>> I am trying to dial out over my PRI, and am getting this error:
>>>
>>> 2010-05-16 01:01:21.452392 [CRIT] zap_io.c:1139 SPAN NOT DEFINED!
>>> 2010-05-16 01:01:21.452392 [ERR] mod_openzap.c:1154 No channels available
>>> 2010-05-16 01:01:21.452392 [ERR] switch_ivr_originate.c:2249 Cannot
>>> create outgoing channel of type [OpenZAP] cause: [NORMAL_CIRCUIT_CONGESTION]
>>>
>>>
>>> This is my openzap.conf:
>>>
>>> [span wanpipe smg_prid]
>>> name => smg_prid
>>> trunk_type =>e1
>>> b-channel => 1:1-15
>>> b-channel => 1:17-31
>>> trunk_type =>e1
>>> b-channel => 2:1-15
>>> b-channel => 2:17-31
>>>
>>>
>>> This is my openzap.conf.xml:
>>>
>>> <configuration name="openzap.conf" description="OpenZAP Configuration">
>>>   <settings>
>>>     <param name="debug" value="0"/>
>>>
>>>   </settings>
>>>   <boost_spans>
>>>         <span id="smg_prid">
>>>         <param name="dialplan" value="XML"/>
>>>         <param name="context" value="default"/>
>>>         </span>
>>>   </boost_spans>
>>>
>>>   <analog_spans>
>>>         <span id="smg_prid">
>>>         <param name="dialplan" value="XML"/>
>>>         <param name="context" value="default"/>
>>>
>>>         </span>
>>>   </analog_spans>
>>> </configuration>
>>>
>>>
>>> And here is the lua code I'm using to dial out:
>>>
>>> sessiondata = "OpenZAP/smg_prid/<num>"
>>> new_session = freeswitch.Session(sessiondata)
>>>
>>>
>>> What am I missing here?
>>> Thanks,
>>> Neil
>>>
>>>
>>>
>>> _______________________________________________
>>> FreeSWITCH-users mailing list
>>> FreeSWITCH-users at lists.freeswitch.org
>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>> http://www.freeswitch.org
>>>
>>>
>>
>> _______________________________________________
>> FreeSWITCH-users mailing list
>> FreeSWITCH-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>>
>
> _______________________________________________
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20100516/739df658/attachment.html