[Freeswitch-users] Freeswitch to cisco router(gateway)

[jay binks]

all you need is..

<action application="bridge"
data="{sip_cid_type=rpid}sofia/**YOURPROFILE**/$1@**CISCOIP**" />

not all IOS's are going to need the caller ID to be forced to rpid,
but in my experience I needed it.  ( it should not hurt anyways )

hope that helps

Jay

On Tue, Mar 9, 2010 at 6:18 PM, Stephen Kingham <
Stephen.Kingham at kingtech.com.au> wrote:

> Hi
>
> I can help out with the Cisco config, but I have not worked out what I
> need to configure FreeSWITCH to route a SIP call to the ip address of
> the Cisco GW.  If I could get a bit of help there I will write, or help
> write howto.
>
> Regards
>
> Stevek
>
>
> On Mon, 2010-03-08 at 18:23 +0100, Tristan Mahé wrote:
> > +1 with Brian,
> >
> > Just as I have 5 spare minutes and to be kind:
> >
> >
> > * E1 controller config:
> >
> > controller E1 0/0/0
> >  framing NO-CRC4
> >  pri-group timeslots 1-31
> >  description E1_1
> > !
> > interface Serial0/0/0:15
> >  no ip address
> >  encapsulation hdlc
> >  isdn switch-type primary-net5
> >  isdn not-end-to-end 64
> >  isdn incoming-voice voice
> >  isdn bchan-number-order descending round-robin
> >  no cdp enable
> > !
> > voice-port 0/0/0:15
> >  no comfort-noise
> >  cptone FR
> >  timeouts call-disconnect 1
> >  timeouts wait-release 1
> > !
> >
> > * Dial-peers ( SIP to E1 and E1 to SIP):
> >
> > dial-peer voice 100 pots
> >  description SIP_TO_E1
> >  destination-pattern 0........
> >  progress_ind setup enable 3
> >  progress_ind progress enable 8
> >  progress_ind connect enable 8
> >  progress_ind disconnect enable 8
> >  no digit-strip
> >  port 0/0/0:15
> > !
> > dial-peer voice 500 voip
> >  description E1_TO_SIP
> >  destination-pattern ....
> >  progress_ind setup enable 3
> >  session protocol sipv2
> >  session target ipv4:FREESWITCH_IP
> >  session transport udp
> >  dtmf-relay rtp-nte
> >  codec g711alaw
> >  no vad
> > !
> >
> >
> > Remember to adapt this config to your needs ( there are mandatory
> > missing parts, but at least you have some config options to look for).
> >
> > Regards,
> >
> > Gled.
> >
> > Brian West a écrit :
> > > You seem rather needy.  Have you even tried google yet?  When asking
> for help you could be more descriptive if you want help.  These "I need
> help" without any directed questioned signals to me you have a job to do and
> you don't know how to do it and you're now asking US to do your job for you.
>   Be descriptive and do some research yourself.  Again we aren't cisco and
> you didn't pay us for that hardware so I would start by venturing over to
> www.cisco.com and searching their docs for that hardware on how to
> configure voice peers.  Then ask questions if anything is left to question.
> > >
> > > /b
> > >
> > > On Mar 8, 2010, at 9:23 AM, srinivasula reddy wrote:
> > >
> > >> HI,
> > >>
> > >> how do i configure freeswitch gateway to communicate to cisco router,
> i am using cisco2921.
> > >>
> > >> Thanks
> > >> Srinivas
> > >
> > >
> > > _______________________________________________
> > > FreeSWITCH-users mailing list
> > > FreeSWITCH-users at lists.freeswitch.org
> > > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> > > UNSUBSCRIBE:
> http://lists.freeswitch.org/mailman/options/freeswitch-users
> > > http://www.freeswitch.org
> >
> > _______________________________________________
> > FreeSWITCH-users mailing list
> > FreeSWITCH-users at lists.freeswitch.org
> > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> > UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> > http://www.freeswitch.org
>
>
> _______________________________________________
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>



-- 
Sincerely

Jay
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20100309/30670ccf/attachment-0001.html