[Freeswitch-users] Sangoma a101

[Peter P GMX]

Q.931 and Q.921 are protocols for Euro ISDN. So this is the right protocol.
See here: http://www.voip-info.org/wiki/view/EuroISDN

Best regards Peter

Niall Crosby schrieb:
> Sorry, my mistake.
>
> I was asked by telco to specifically use Euro dialect, will using Q931
> cause any issues?
>
> tnks
>
> 2009/7/31 Peter P GMX <Prometheus001 at gmx.net>:
>   
>>> I was asked by telco to specifically use telco, will using Q931 cause
>>> any issues for me?
>>>       
>> Sorry, I do not not understand that question.
>>
>> Best regards
>> Peter
>>
>> Niall Crosby schrieb:
>>     
>>> Thanks for help.
>>>
>>> Got my alarms sorted - telco had problem there.
>>>
>>> As for my Freeswitch problem, chaning to Q931 clears the error message.
>>>
>>> I was asked by telco to specifically use telco, will using Q931 cause
>>> any issues for me?
>>>
>>> Thanks again,
>>> Niall.
>>>
>>> 2009/7/31 Peter P GMX <Prometheus001 at gmx.net>:
>>>
>>>       
>>>> Firstly I would try get get rid of the sangoma errors. There are 2 errors:
>>>>
>>>> Short Circuit:  ON
>>>> Loss of Signal: ON
>>>>
>>>> So either the card is not configured correctly or there is a cabling
>>>> problem. What is your wanpipe1.conf?
>>>>
>>>> Second, if euro doesn't work, try Q931.
>>>> I had success with that some time ago.
>>>>
>>>> Best regards
>>>> Peter
>>>>
>>>> Niall Crosby schrieb:
>>>>
>>>>         
>>>>> Hi,
>>>>>
>>>>> This might be Sangoma config issue, so apologies in advance for
>>>>> posting it here if it is. I am waiting for Sangoma helpdesk to get
>>>>> back to me!
>>>>>
>>>>> But I have a Sangoma a101 and trying to get it working with
>>>>> Freeswitch. Have E1 line coming from telco and everything set up
>>>>> correctly (to my best efforts), however when Freeswitch starts, it
>>>>> says:
>>>>>
>>>>> 2009-07-30 15:17:15.446569 [ERR] mod_openzap.c:1953 Error starting
>>>>> OpenZAP span 1 mode: user dialect: euro error:
>>>>>
>>>>> Also I'm getting the following Sangoma alarms:
>>>>>
>>>>> ***** w1g1: E1 Alarms (Framer) *****
>>>>>
>>>>> ALOS:   OFF     | LOS:  ON
>>>>> RED:    ON      | AIS:  OFF
>>>>> OOF:    ON      | RAI:  OFF
>>>>>
>>>>> ***** w1g1: E1 Alarms (LIU) *****
>>>>>
>>>>> Short Circuit:  ON
>>>>> Open Circuit:   OFF
>>>>> Loss of Signal: ON
>>>>>
>>>>>
>>>>> Can someone tell me where I should be focusing my attention - on the
>>>>> Sangoma config or the Freeswitch config?
>>>>>
>>>>> Also what state should the Sangoma alarms be in when Freeswitch is NOT
>>>>> running? Should they all clear?
>>>>>
>>>>> Thanks in advance,
>>>>> Niall.
>>>>>
>>>>>
>>>>>
>>>>>
>>>>>           
>>>> _______________________________________________
>>>> FreeSWITCH-users mailing list
>>>> FreeSWITCH-users at lists.freeswitch.org
>>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>>> http://www.freeswitch.org
>>>>
>>>>
>>>>         
>>>
>>>
>>>       
>> _______________________________________________
>> FreeSWITCH-users mailing list
>> FreeSWITCH-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>>     
>
>
>
>