[Freeswitch-users] Sangoma a101

[Niall Crosby]

Sorry, my mistake.

I was asked by telco to specifically use Euro dialect, will using Q931
cause any issues?

tnks

2009/7/31 Peter P GMX <Prometheus001 at gmx.net>:
>>I was asked by telco to specifically use telco, will using Q931 cause
>>any issues for me?
>
> Sorry, I do not not understand that question.
>
> Best regards
> Peter
>
> Niall Crosby schrieb:
>> Thanks for help.
>>
>> Got my alarms sorted - telco had problem there.
>>
>> As for my Freeswitch problem, chaning to Q931 clears the error message.
>>
>> I was asked by telco to specifically use telco, will using Q931 cause
>> any issues for me?
>>
>> Thanks again,
>> Niall.
>>
>> 2009/7/31 Peter P GMX <Prometheus001 at gmx.net>:
>>
>>> Firstly I would try get get rid of the sangoma errors. There are 2 errors:
>>>
>>> Short Circuit:  ON
>>> Loss of Signal: ON
>>>
>>> So either the card is not configured correctly or there is a cabling
>>> problem. What is your wanpipe1.conf?
>>>
>>> Second, if euro doesn't work, try Q931.
>>> I had success with that some time ago.
>>>
>>> Best regards
>>> Peter
>>>
>>> Niall Crosby schrieb:
>>>
>>>> Hi,
>>>>
>>>> This might be Sangoma config issue, so apologies in advance for
>>>> posting it here if it is. I am waiting for Sangoma helpdesk to get
>>>> back to me!
>>>>
>>>> But I have a Sangoma a101 and trying to get it working with
>>>> Freeswitch. Have E1 line coming from telco and everything set up
>>>> correctly (to my best efforts), however when Freeswitch starts, it
>>>> says:
>>>>
>>>> 2009-07-30 15:17:15.446569 [ERR] mod_openzap.c:1953 Error starting
>>>> OpenZAP span 1 mode: user dialect: euro error:
>>>>
>>>> Also I'm getting the following Sangoma alarms:
>>>>
>>>> ***** w1g1: E1 Alarms (Framer) *****
>>>>
>>>> ALOS:   OFF     | LOS:  ON
>>>> RED:    ON      | AIS:  OFF
>>>> OOF:    ON      | RAI:  OFF
>>>>
>>>> ***** w1g1: E1 Alarms (LIU) *****
>>>>
>>>> Short Circuit:  ON
>>>> Open Circuit:   OFF
>>>> Loss of Signal: ON
>>>>
>>>>
>>>> Can someone tell me where I should be focusing my attention - on the
>>>> Sangoma config or the Freeswitch config?
>>>>
>>>> Also what state should the Sangoma alarms be in when Freeswitch is NOT
>>>> running? Should they all clear?
>>>>
>>>> Thanks in advance,
>>>> Niall.
>>>>
>>>>
>>>>
>>>>
>>> _______________________________________________
>>> FreeSWITCH-users mailing list
>>> FreeSWITCH-users at lists.freeswitch.org
>>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>>> http://www.freeswitch.org
>>>
>>>
>>
>>
>>
>>
>
> _______________________________________________
> FreeSWITCH-users mailing list
> FreeSWITCH-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>



-- 
-- 
Sremium Ltd.

Reg Number: 451937

Mobile: +353 (0)87 2393174
Web: www.sremium.com

The information transmitted is intended only for the person or entity
to which it is addressed and may contain confidential and/or
privileged material. Statements and opinions expressed in this e-mail
may not represent those of Sremium. Any review, retransmission,
dissemination or other use of, or taking of any action in reliance
upon, this information by persons or entities other than the intended
recipient is prohibited. If you received this in error, please contact
the sender immediately and delete the material from any computer.