[Freeswitch-users] TDM400 FXO can dialout only once

Anthony Minessale anthony.minessale at gmail.com
Mon Jan 26 08:33:51 PST 2009 

The unhanded type message just means that mod_openzap does not do anything
with the TONE_DETECTED event that was passed
up from the ozmod_analog.

On Mon, Jan 26, 2009 at 7:32 AM, Nandy Dagondon <gcd at i.ph> wrote:

> that's great. yes, i'm in the philippines. there's a difference in dialtone
> - it's 425 Hz.
>  -nandy
>
>
>
> On Mon, Jan 26, 2009 at 6:01 PM, Michael Collins <msc at freeswitch.org>wrote:
>
>> I have a TDM400 clone and I will see if I can reproduce these
>> symptoms. BTW, are you in the Philippines? Is there any difference in
>> the dial tone there than in the US?
>> -MC
>>
>> On Sun, Jan 25, 2009 at 11:05 PM, Nandy Dagondon <gcd at i.ph> wrote:
>> > i monitored the line using another phone. there's indeed dialtone in all
>> > attempts.
>> > i see TONE_DETECTED in the first call but i wonder there's a WARNING
>> message
>> > immediately following [WARNING] mod_openzap.c:1196 on_fxo_signal()
>> Unhandled
>> > type for channel 2:1.
>> > the dialtone freq should be okay since it's detected in the first
>> call.could
>> > the WARNING message gives us a hint of a possible problem other than the
>> > dialtone freq?
>> >
>> > okay, i'll try the SVN version next.
>> >
>> >
>> > On Mon, Jan 26, 2009 at 10:18 AM, Anthony Minessale
>> > <anthony.minessale at gmail.com> wrote:
>> >>
>> >> Its not detecting a dial tone on the failure case.
>> >> Before dialing it waits until it picks up dialtone.
>> >> Try the svn trunk version to see if it works any better or verify there
>> is
>> >> a dialtone on the line.
>> >>
>> >> On Jan 25, 2009 6:19 PM, "Nandy Dagondon" <gcd at i.ph> wrote:
>> >>
>> >> hi everybody,
>> >>
>> >> i installed FS 1.0.2 to an Atom mobo (Intel D945GCLF2). it's working
>> using
>> >> IP phones, softphones and digium FXS port. but there's a problem in
>> dialing
>> >> out to PSTN using digium tdm400 fxo - it works fine on the first
>> attempt
>> >> (after starting FS) but it fails on the subsequent attempts. i tested
>> to
>> >> call using the FXS port and IP phone. same problem.
>> >>
>> >> before i place any call,  i checked >oz dump 2 1 (show current state =
>> >> DOWN, last state = DOWN)
>> >>
>> >> in the first call, there's this message:
>> >> [WARNING] mod_openzap.c:1196 on_fxo_signal() Unhandled type for channel
>> >> 2:1
>> >> but
>> >>
>> >> then i hangup. checked >oz dump 21 (show current state=DOWN, last
>> >> state=HANGUP)
>> >>
>> >> in the 2nd (and subsequent) attempts, the fxo just goes off-hook but
>> >> doesn't send the dtmf tones.
>> >> >oz dump 2 1 (shows current state = DIALING, last state = DOWN)
>> >>
>> >> has anyone encountered this problem before? i appreciate for any help
>> to
>> >> correct this problem.
>> >>
>> >> tks,
>> >> nandy
>> >>
>> >>
>> >> Environment:
>> >> ==================
>> >> kernel 2.6.18-92.1.22.el5
>> >> FS 1.0.2
>> >> zaptel 1.4.11
>> >> oslec
>> >> digium TDM400P Rev. I (1-FXS, 2-FXO,3-4 vacant)
>> >>
>> >> zaptel.conf
>> >> ========
>> >> loadzone = us
>> >> defaultzone=us
>> >> channels=1-2
>> >> alaw=1-4
>> >> fxsks=2
>> >> fxoks=1
>> >>
>> >>
>> >> openzap.conf.xml:
>> >> ===============
>> >> <configuration name="openzap.conf" description="OpenZAP Configuration">
>> >>   <settings>
>> >>     <param name="debug" value="9"/>
>> >>     <!-- <param name="hold-music" value="$${moh_uri}"/> -->
>> >>     <!-- <param name="enable-analog-option" value="call-swap"/> -->
>> >>     <!-- <param name="enable-analog-option" value="3-way"/> -->
>> >>   </settings>
>> >>   <!-- one entry here per openzap span -->
>> >>   <analog_spans>
>> >>     <span id="1">
>> >>       <!--<param name="hold-music" value="$${moh_uri}"/>-->
>> >>       <!--<param name="enable-analog-option" value="call-swap"/>-->
>> >>       <!--<param name="enable-analog-option" value="3-way"/>-->
>> >>       <param name="tonegroup" value="us"/>
>> >>       <param name="digit-timeout" value="2000"/>
>> >>       <param name="max-digits" value="15"/>
>> >>       <param name="dialplan" value="XML"/>
>> >>       <param name="context" value="default"/>
>> >>       <param name="enable-callerid" value="false"/>
>> >>       <!-- regex to stop dialing when it matches -->
>> >>       <!--<param name="dial-regex" value="5555"/>-->
>> >>       <!-- regex to stop dialing when it does not match -->
>> >>       <!--<param name="fail-dial-regex" value="^5"/>-->
>> >>     </span>
>> >>     <span id="2">
>> >>       <!--<param name="hold-music" value="$${moh_uri}"/>-->
>> >>       <!--<param name="enable-analog-option" value="call-swap"/>-->
>> >>       <!--<param name="enable-analog-option" value="3-way"/>-->
>> >>       <param name="tonegroup" value="us"/>
>> >>       <param name="digit-timeout" value="2000"/>
>> >>       <param name="max-digits" value="11"/>
>> >>       <param name="dialplan" value="XML"/>
>> >>       <param name="context" value="default"/>
>> >>       <param name="enable-callerid" value=""false/>
>> >>       <!-- regex to stop dialing when it matches -->
>> >>       <!--<param name="dial-regex" value="5555"/>-->
>> >>       <!-- regex to stop dialing when it does not match -->
>> >>       <!--<param name="fail-dial-regex" value="^5"/>-->
>> >>     </span>
>> >>   </analog_spans>
>> >> </configuration>
>> >>
>> >> openzap.conf
>> >> ==========
>> >> [span zt]
>> >> name => OpenZAP FXS
>> >> number => 1
>> >> fxs-channel => 1
>> >>
>> >> [span zt]
>> >> name => OpenZAP FXO
>> >> number => 2
>> >> fxo-channel => 2
>> >>
>> >> tones.conf  (the dialtone and ring tone is set to Philipping tones)
>> >> ========
>> >> [us]
>> >> generate-dial => v=-7;%(1000,0,425)
>> >> detect-dial => 425
>> >>
>> >> generate-ring => v=-7;%(1000,4000,425,480)
>> >> detect-ring => 425,480
>> >>
>> >> generate-busy => v=-7;%(500,500,480,620)
>> >> detect-busy => 480,620
>> >>
>> >> generate-attn => v=0;%(200,300,1400,1800)
>> >> detect-attn => 1400,1800
>> >>
>> >> generate-callwaiting-sas => v=0;%(300,10000,440)
>> >> detect-callwaiting-sas => 440
>> >>
>> >> generate-callwaiting-cas => v=0;%(80,0,2750,2130)
>> >> detect-callwaiting-cas => 2750,2130
>> >>
>> >> detect-fail1 => 913.8
>> >> detect-fail2 => 1370.6
>> >> detect-fail3 => 776.7
>> >>
>> >> LOG OF FIRST CALL (OK)
>> >> ====================
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:152
>> >> switch_core_standard_on_execute() OpenZAP/1:1/93400534 Execute
>> >> bridge(openzap/2/1/3400534)
>> >> 2009-01-25 10:35:58 [DEBUG] mod_openzap.c:340 tech_init() Set codec
>> PCMU
>> >> 20ms
>> >> 2009-01-25 10:35:58 [DEBUG] mod_openzap.c:1017
>> channel_outgoing_channel()
>> >> Connect outbound channel OpenZAP/2:1/3400534
>> >> 2009-01-25 10:35:58 [NOTICE] switch_channel.c:565
>> >> switch_channel_set_name() New Channel OpenZAP/2:1/3400534
>> >> [e5f12114-ea88-11dd-9f5c-290fb4a527a4]
>> >> 2009-01-25 10:35:58 [DEBUG] mod_openzap.c:1026
>> channel_outgoing_channel()
>> >> (OpenZAP/2:1/3400534) State Change CS_NEW -> CS_INIT
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:35:58 [DEBUG] ozmod_analog.c:52
>> analog_fxo_outgoing_call()
>> >> Changing state on 2:1 from DOWN to DIALING
>> >> 2009-01-25 10:35:58 [DEBUG] ozmod_analog.c:239 zap_analog_channel_run()
>> >> ANALOG CHANNEL thread starting.
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> CS_INIT
>> >> 2009-01-25 10:35:58 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for DIALING
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:444
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State INIT
>> >> 2009-01-25 10:35:58 [DEBUG] mod_openzap.c:364 channel_on_init()
>> >> (OpenZAP/2:1/3400534) State Change CS_INIT -> CS_ROUTING
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:444
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State INIT going to
>> sleep
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_ROUTING
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:447
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING
>> >> 2009-01-25 10:35:58 [DEBUG] mod_openzap.c:387 channel_on_routing()
>> >> OpenZAP/2:1/3400534 CHANNEL ROUTING
>> >> 2009-01-25 10:35:58 [DEBUG] switch_ivr_originate.c:58
>> >> originate_on_routing() (OpenZAP/2:1/3400534) State Change CS_ROUTING ->
>> >> CS_CONSUME_MEDIA
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:447
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING going to
>> sleep
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_CONSUME_MEDIA
>> >> 2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:466
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA
>> >> 2009-01-25 10:35:59 [DEBUG] ozmod_analog.c:615 zap_analog_channel_run()
>> >> Detected tone DIAL on 2:1
>> >> 2009-01-25 10:35:59 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO
>> sig
>> >> 2:1 [TONE_DETECTED]
>> >> 2009-01-25 10:35:59 [WARNING] mod_openzap.c:1196 on_fxo_signal()
>> Unhandled
>> >> type for channel 2:1
>> >> 2009-01-25 10:35:59 [DEBUG] zap_io.c:1179 zchan_activate_dtmf_buffer()
>> >> Created DTMF Buffer!
>> >> 2009-01-25 10:35:59 [DEBUG] zap_io.c:1715 handle_dtmf() 2:1 GENERATE
>> DTMF
>> >> [3400534]
>> >> 2009-01-25 10:36:03 [DEBUG] ozmod_analog.c:302 zap_analog_channel_run()
>> >> Changing state on 2:1 from DIALING to UP
>> >> 2009-01-25 10:36:03 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for UP
>> >> 2009-01-25 10:36:03 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO
>> sig
>> >> 2:1 [UP]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_channel.c:1710
>> >> switch_channel_perform_mark_answered() Send signal OpenZAP/1:1/93400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:03 [NOTICE] mod_openzap.c:1180 on_fxo_signal() Channel
>> >> [OpenZAP/2:1/3400534] has been answered
>> >> 2009-01-25 10:36:03 [DEBUG] switch_channel.c:177
>> >> switch_channel_audio_sync() OpenZAP/2:1/3400534 receive message
>> [AUDIO_SYNC]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_channel.c:1768
>> >> switch_channel_perform_answer() OpenZAP/1:1/93400534 receive message
>> >> [ANSWER]
>> >> 2009-01-25 10:36:03 [DEBUG] mod_openzap.c:813
>> >> channel_receive_message_fxs() Changing state on 1:1 from IDLE to UP
>> >> 2009-01-25 10:36:03 [NOTICE] mod_openzap.c:814
>> >> channel_receive_message_fxs() Channel [OpenZAP/1:1/93400534] has been
>> >> answered
>> >> 2009-01-25 10:36:03 [DEBUG] switch_channel.c:177
>> >> switch_channel_audio_sync() OpenZAP/1:1/93400534 receive message
>> >> [AUDIO_SYNC]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_session.c:511
>> >> switch_core_session_perform_receive_message() Send signal
>> >> OpenZAP/1:1/93400534 [BREAK]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_ivr_originate.c:1627
>> >> switch_ivr_originate() Originate Resulted in Success:
>> [OpenZAP/2:1/3400534]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_channel.c:177
>> >> switch_channel_audio_sync() OpenZAP/2:1/3400534 receive message
>> [AUDIO_SYNC]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_channel.c:177
>> >> switch_channel_audio_sync() OpenZAP/1:1/93400534 receive message
>> >> [AUDIO_SYNC]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_ivr_bridge.c:862
>> >> switch_ivr_multi_threaded_bridge() OpenZAP/2:1/3400534 receive message
>> >> [BRIDGE]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_session.c:511
>> >> switch_core_session_perform_receive_message() Send signal
>> >> OpenZAP/2:1/3400534 [BREAK]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_ivr_bridge.c:869
>> >> switch_ivr_multi_threaded_bridge() OpenZAP/1:1/93400534 receive message
>> >> [BRIDGE]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_session.c:511
>> >> switch_core_session_perform_receive_message() Send signal
>> >> OpenZAP/1:1/93400534 [BREAK]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_ivr_bridge.c:913
>> >> switch_ivr_multi_threaded_bridge() (OpenZAP/2:1/3400534) State Change
>> >> CS_CONSUME_MEDIA -> CS_EXCHANGE_MEDIA
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:03 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 1:1 for UP
>> >> 2009-01-25 10:36:03 [DEBUG] mod_openzap.c:1212 on_fxs_signal() got FXS
>> sig
>> >> [UP]
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_state_machine.c:466
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA
>> going to
>> >> sleep
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_EXCHANGE_MEDIA
>> >> 2009-01-25 10:36:03 [DEBUG] switch_core_state_machine.c:457
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State EXCHANGE_MEDIA
>> >> 2009-01-25 10:36:03 [DEBUG] mod_openzap.c:511
>> channel_on_exchange_media()
>> >> CHANNEL EXCHANGE_MEDIA
>> >> 2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:744 process_event() EVENT
>> >> [ONHOOK][1:1] STATE [UP]
>> >> 2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:780 process_event() Changing
>> >> state on 1:1 from UP to DOWN
>> >> 2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 1:1 for DOWN
>> >> 2009-01-25 10:36:16 [DEBUG] mod_openzap.c:1212 on_fxs_signal() got FXS
>> sig
>> >> [STOP]
>> >> 2009-01-25 10:36:16 [NOTICE] mod_openzap.c:1300 on_fxs_signal() Hangup
>> >> OpenZAP/1:1/93400534 [CS_EXECUTE] [NORMAL_CLEARING]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_channel.c:1494
>> >> switch_channel_perform_hangup() Send signal OpenZAP/1:1/93400534 [KILL]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/1:1/93400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:16 [DEBUG] zap_io.c:1125 zap_channel_done() channel
>> done
>> >> 1:1
>> >> 2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
>> >> ANALOG CHANNEL 1:1 thread ended.
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:360
>> audio_bridge_thread()
>> >> OpenZAP/1:1/93400534 ending bridge by request from read function
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:435
>> audio_bridge_thread()
>> >> BRIDGE THREAD DONE [OpenZAP/1:1/93400534]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:439
>> audio_bridge_thread()
>> >> Send signal OpenZAP/2:1/3400534 [BREAK]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:354
>> audio_bridge_thread()
>> >> OpenZAP/1:1/93400534 ending bridge by request from write function
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:409
>> audio_bridge_thread()
>> >> OpenZAP/2:1/3400534 receive message [UNBRIDGE]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_session.c:511
>> >> switch_core_session_perform_receive_message() Send signal
>> >> OpenZAP/2:1/3400534 [BREAK]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:435
>> audio_bridge_thread()
>> >> BRIDGE THREAD DONE [OpenZAP/2:1/3400534]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:439
>> audio_bridge_thread()
>> >> Send signal OpenZAP/1:1/93400534 [BREAK]
>> >> 2009-01-25 10:36:16 [NOTICE] switch_ivr_bridge.c:470
>> >> audio_bridge_on_exchange_media() Hangup OpenZAP/2:1/3400534
>> >> [CS_EXCHANGE_MEDIA] [NORMAL_CLEARING]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_channel.c:1494
>> >> switch_channel_perform_hangup() Send signal OpenZAP/2:1/3400534 [KILL]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:457
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State EXCHANGE_MEDIA
>> going
>> >> to sleep
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] mod_openzap.c:429 channel_on_hangup()
>> Changing
>> >> state on 2:1 from UP to HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] mod_openzap.c:472 channel_on_hangup()
>> >> OpenZAP/2:1/3400534 CHANNEL HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:46
>> >> switch_core_standard_on_hangup() OpenZAP/2:1/3400534 Standard HANGUP,
>> cause:
>> >> NORMAL_CLEARING
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP going to
>> sleep
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_session.c:939
>> >> switch_core_session_thread() Session 2 (OpenZAP/2:1/3400534) Locked,
>> Waiting
>> >> on external entities
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:454
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) State EXECUTE going to
>> >> sleep
>> >> 2009-01-25 10:36:16 [NOTICE] switch_core_session.c:957
>> >> switch_core_session_thread() Session 2 (OpenZAP/2:1/3400534) Ended
>> >> 2009-01-25 10:36:16 [NOTICE] switch_core_session.c:959
>> >> switch_core_session_thread() Close Channel OpenZAP/2:1/3400534
>> [CS_HANGUP]
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) Running State Change
>> >> CS_HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] mod_openzap.c:472 channel_on_hangup()
>> >> OpenZAP/1:1/93400534 CHANNEL HANGUP
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:46
>> >> switch_core_standard_on_hangup() OpenZAP/1:1/93400534 Standard HANGUP,
>> >> cause: NORMAL_CLEARING
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP going to
>> sleep
>> >> 2009-01-25 10:36:16 [DEBUG] switch_core_session.c:939
>> >> switch_core_session_thread() Session 1 (OpenZAP/1:1/93400534) Locked,
>> >> Waiting on external entities
>> >> 2009-01-25 10:36:16 [NOTICE] switch_core_session.c:957
>> >> switch_core_session_thread() Session 1 (OpenZAP/1:1/93400534) Ended
>> >> 2009-01-25 10:36:16 [NOTICE] switch_core_session.c:959
>> >> switch_core_session_thread() Close Channel OpenZAP/1:1/93400534
>> [CS_HANGUP]
>> >> 2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for HANGUP
>> >> 2009-01-25 10:36:17 [DEBUG] ozmod_analog.c:351 zap_analog_channel_run()
>> >> Changing state on 2:1 from HANGUP to DOWN
>> >> 2009-01-25 10:36:17 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for DOWN
>> >> 2009-01-25 10:36:17 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO
>> sig
>> >> 2:1 [STOP]
>> >> 2009-01-25 10:36:17 [DEBUG] zap_io.c:1125 zap_channel_done() channel
>> done
>> >> 2:1
>> >> 2009-01-25 10:36:17 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
>> >> ANALOG CHANNEL 2:1 thread ended.
>> >>
>> >> LOG OF FAILED CALLS
>> >> ==================
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:152
>> >> switch_core_standard_on_execute() OpenZAP/1:1/93400534 Execute
>> >> bridge(openzap/2/1/3400534)
>> >> 2009-01-25 10:36:55 [DEBUG] mod_openzap.c:340 tech_init() Set codec
>> PCMU
>> >> 20ms
>> >> 2009-01-25 10:36:55 [DEBUG] mod_openzap.c:1017
>> channel_outgoing_channel()
>> >> Connect outbound channel OpenZAP/2:1/3400534
>> >> 2009-01-25 10:36:55 [NOTICE] switch_channel.c:565
>> >> switch_channel_set_name() New Channel OpenZAP/2:1/3400534
>> >> [079f5420-ea89-11dd-9f5c-290fb4a527a4]
>> >> 2009-01-25 10:36:55 [DEBUG] mod_openzap.c:1026
>> channel_outgoing_channel()
>> >> (OpenZAP/2:1/3400534) State Change CS_NEW -> CS_INIT
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:55 [DEBUG] ozmod_analog.c:52
>> analog_fxo_outgoing_call()
>> >> Changing state on 2:1 from DOWN to DIALING
>> >> 2009-01-25 10:36:55 [DEBUG] ozmod_analog.c:239 zap_analog_channel_run()
>> >> ANALOG CHANNEL thread starting.
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> CS_INIT
>> >> 2009-01-25 10:36:55 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for DIALING
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:444
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State INIT
>> >> 2009-01-25 10:36:55 [DEBUG] mod_openzap.c:364 channel_on_init()
>> >> (OpenZAP/2:1/3400534) State Change CS_INIT -> CS_ROUTING
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:444
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State INIT going to
>> sleep
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_ROUTING
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:447
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING
>> >> 2009-01-25 10:36:55 [DEBUG] mod_openzap.c:387 channel_on_routing()
>> >> OpenZAP/2:1/3400534 CHANNEL ROUTING
>> >> 2009-01-25 10:36:55 [DEBUG] switch_ivr_originate.c:58
>> >> originate_on_routing() (OpenZAP/2:1/3400534) State Change CS_ROUTING ->
>> >> CS_CONSUME_MEDIA
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:447
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING going to
>> sleep
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_CONSUME_MEDIA
>> >> 2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:466
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA
>> >> 2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:744 process_event() EVENT
>> >> [ONHOOK][1:1] STATE [IDLE]
>> >> 2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:780 process_event() Changing
>> >> state on 1:1 from IDLE to DOWN
>> >> 2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 1:1 for DOWN
>> >> 2009-01-25 10:37:08 [DEBUG] mod_openzap.c:1212 on_fxs_signal() got FXS
>> sig
>> >> [STOP]
>> >> 2009-01-25 10:37:08 [NOTICE] mod_openzap.c:1300 on_fxs_signal() Hangup
>> >> OpenZAP/1:1/93400534 [CS_EXECUTE] [NORMAL_CLEARING]
>> >> 2009-01-25 10:37:08 [DEBUG] switch_channel.c:1494
>> >> switch_channel_perform_hangup() Send signal OpenZAP/1:1/93400534 [KILL]
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/1:1/93400534
>> >> [BREAK]
>> >> 2009-01-25 10:37:08 [DEBUG] zap_io.c:1125 zap_channel_done() channel
>> done
>> >> 1:1
>> >> 2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
>> >> ANALOG CHANNEL 1:1 thread ended.
>> >> 2009-01-25 10:37:08 [NOTICE] switch_ivr_originate.c:1566
>> >> switch_ivr_originate() Hangup OpenZAP/2:1/3400534 [CS_CONSUME_MEDIA]
>> >> [ORIGINATOR_CANCEL]
>> >> 2009-01-25 10:37:08 [DEBUG] switch_channel.c:1494
>> >> switch_channel_perform_hangup() Send signal OpenZAP/2:1/3400534 [KILL]
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_session.c:807
>> >> switch_core_session_signal_state_change() Send signal
>> OpenZAP/2:1/3400534
>> >> [BREAK]
>> >> 2009-01-25 10:37:08 [DEBUG] switch_ivr_originate.c:1691
>> >> switch_ivr_originate() Originate Cancelled by originator termination
>> Cause:
>> >> 487 [ORIGINATOR_CANCEL]
>> >> 2009-01-25 10:37:08 [INFO] mod_dptools.c:1909 audio_bridge_function()
>> >> Originate Failed.  Cause: ORIGINATOR_CANCEL
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:454
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) State EXECUTE going to
>> >> sleep
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) Running State Change
>> >> CS_HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] mod_openzap.c:472 channel_on_hangup()
>> >> OpenZAP/1:1/93400534 CHANNEL HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:46
>> >> switch_core_standard_on_hangup() OpenZAP/1:1/93400534 Standard HANGUP,
>> >> cause: NORMAL_CLEARING
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP going to
>> sleep
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_session.c:939
>> >> switch_core_session_thread() Session 3 (OpenZAP/1:1/93400534) Locked,
>> >> Waiting on external entities
>> >> 2009-01-25 10:37:08 [NOTICE] switch_core_session.c:957
>> >> switch_core_session_thread() Session 3 (OpenZAP/1:1/93400534) Ended
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:466
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA
>> going to
>> >> sleep
>> >> 2009-01-25 10:37:08 [NOTICE] switch_core_session.c:959
>> >> switch_core_session_thread() Close Channel OpenZAP/1:1/93400534
>> [CS_HANGUP]
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:379
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
>> >> CS_HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] mod_openzap.c:429 channel_on_hangup()
>> Changing
>> >> state on 2:1 from DIALING to HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] mod_openzap.c:472 channel_on_hangup()
>> >> OpenZAP/2:1/3400534 CHANNEL HANGUP
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:46
>> >> switch_core_standard_on_hangup() OpenZAP/2:1/3400534 Standard HANGUP,
>> cause:
>> >> ORIGINATOR_CANCEL
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
>> >> switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP going to
>> sleep
>> >> 2009-01-25 10:37:08 [DEBUG] switch_core_session.c:939
>> >> switch_core_session_thread() Session 4 (OpenZAP/2:1/3400534) Locked,
>> Waiting
>> >> on external entities
>> >> 2009-01-25 10:37:08 [NOTICE] switch_core_session.c:957
>> >> switch_core_session_thread() Session 4 (OpenZAP/2:1/3400534) Ended
>> >> 2009-01-25 10:37:08 [NOTICE] switch_core_session.c:959
>> >> switch_core_session_thread() Close Channel OpenZAP/2:1/3400534
>> [CS_HANGUP]
>> >> 2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for HANGUP
>> >> 2009-01-25 10:37:09 [DEBUG] ozmod_analog.c:351 zap_analog_channel_run()
>> >> Changing state on 2:1 from HANGUP to DOWN
>> >> 2009-01-25 10:37:09 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
>> >> Executing state handler on 2:1 for DOWN
>> >> 2009-01-25 10:37:09 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO
>> sig
>> >> 2:1 [STOP]
>> >> 2009-01-25 10:37:09 [DEBUG] zap_io.c:1125 zap_channel_done() channel
>> done
>> >> 2:1
>> >> 2009-01-25 10:37:09 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
>> >> ANALOG CHANNEL 2:1 thread ended.
>> >>
>> >>
>> >>
>> >>
>> >>
>> >>
>> >> _______________________________________________
>> >> Freeswitch-users mailing list
>> >> Freeswitch-users at lists.freeswitch.org
>> >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> >> UNSUBSCRIBE:
>> http://lists.freeswitch.org/mailman/options/freeswitch-users
>> >> http://www.freeswitch.org
>> >>
>> >>
>> >> _______________________________________________
>> >> Freeswitch-users mailing list
>> >> Freeswitch-users at lists.freeswitch.org
>> >> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> >> UNSUBSCRIBE:
>> http://lists.freeswitch.org/mailman/options/freeswitch-users
>> >> http://www.freeswitch.org
>> >>
>> >
>> >
>> > _______________________________________________
>> > Freeswitch-users mailing list
>> > Freeswitch-users at lists.freeswitch.org
>> > http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> > UNSUBSCRIBE:
>> http://lists.freeswitch.org/mailman/options/freeswitch-users
>> > http://www.freeswitch.org
>> >
>> >
>>
>> _______________________________________________
>> Freeswitch-users mailing list
>> Freeswitch-users at lists.freeswitch.org
>> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
>> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
>> http://www.freeswitch.org
>>
>
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org
>
>


-- 
Anthony Minessale II

FreeSWITCH http://www.freeswitch.org/
ClueCon http://www.cluecon.com/

AIM: anthm
MSN:anthony_minessale at hotmail.com <MSN%3Aanthony_minessale at hotmail.com>
GTALK/JABBER/PAYPAL:anthony.minessale at gmail.com<PAYPAL%3Aanthony.minessale at gmail.com>
IRC: irc.freenode.net #freeswitch

FreeSWITCH Developer Conference
sip:888 at conference.freeswitch.org <sip%3A888 at conference.freeswitch.org>
iax:guest at conference.freeswitch.org/888
googletalk:conf+888 at conference.freeswitch.org<googletalk%3Aconf%2B888 at conference.freeswitch.org>
pstn:213-799-1400
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20090126/5376149d/attachment-0002.html

More information about the FreeSWITCH-users mailing list